Physical processes in a low-power inductive plasma source in the presence of a weak magnetic field

Research into the influence of a weak external magnetic field (<150 G) on the efficiency of power coupling to plasma and on the structure of axial RF fields in plasma is presented. Power coupling to the discharge plasma as well as the structure of the axial component of RF magnetic fields are shown to depend on the external magnetic field’s magnitude in a nonmonotous manner.

Some effects of flow expansion on the aerodynamics of horizontal-axis wind turbines

The flow upwind of an energy-extracting horizontal-axis wind turbine expands as it approaches the rotor, and the expansion continues in the vorticity-bearing wake behind the rotor. The upwind expansion has long been known to influence the axial momentum equation through the axial component of the pressure, although the extent of the influence has not been quantified. Starting with the impulse analysis of Limacher and Wood (2020), but making no further use of impulse techniques, we derive its exact expression when the rotor is a circumferentially uniform disc. This expression, which depends on the radial velocity and the axial induction factor, is added to the thrust equation containing the pressure on the back of the disc. Removing the pressure to obtain a practically useful equation shows the axial induction in the far wake is twice the value at the rotor only at high tip speed ratio and only if the relationship between vortex pitch and axial induction in non-expanding flow carries over to the expanding case. At high tip speed ratio, we assume that the expanding wake approaches the Joukowsky model of a hub vortex on the axis of rotation and tip vortices originating from each blade. The additional assumption that the helical tip vortices have constant pitch allows a semi-analytic treatment of their effect on the rotor flow. Expansion modifies the relation between the pitch and induced axial velocity so that the far-wake area and induction are significantly less than twice the values at the rotor. There is a moderate decrease – about 6 % – in the power production, and a similar size error occurs in the familiar axial momentum equation involving the axial velocity.

A Nitric Oxide–Modulated Variable-Order Fractional Maxwell Viscoelastic Model of Cerebral Vascular Walls

It is well known that the mechanical behavior of arterial walls plays an important role in the pathogenesis of vascular diseases. Most studies existing in the literature focus on the mechanical interactions between the blood flow and wall’s deformations. However, in the brain, the smaller vessels experience not only oscillatory forces due to the pulsatile blood flow but also structural and morphological changes controlled by the surrounding brain cells. In this study, the mechanical deformation of the cerebral arterial wall caused by the pulsatile blood flow and the dynamics of the neuronal nitric oxide (NO) is investigated. NO is a small diffusive gaseous molecule produced by the endothelial cells and neurons, which is involved in the regulation of cerebral blood flow and pressure. The cerebral vessel is assumed to be a hollow axial symmetric cylinder whose wall thickness is much smaller than the cylinder’s radius and longitudinal length is much less than the propagating wavelength. The wall is an isotropic, homogeneous linear viscoelastic material described by an NO-modulated variable-order fractional Maxwell model. A fractional telegraph equation is obtained for the axial component of the displacement. Patterns of wall’s deformation are investigated through numerical simulations. The results suggest that a significantly decreased inactivation of the neuronal NO may cause a reduction in the shear stress at the blood-vessel interface, which could lead to a decrease in the production of shear-induced endothelial NO and neurovascular disease.

Study of the structure of gas flow іn a cyclone wіth іntermedіate dust removal

The works in which designs of the dust collectors, which are often used in the industry, are analyzed. It is shown that the efficiency of dust collectors largely depends on the structure of the gas flow in the apparatus. Based on the analysis of the current cyclone devices, a picture of the separation process is obtained, and the factors that negatively affect the operation of dust collectors are identified. It is established that forecasting the work of dust collecting devices in certain conditions is most effective to perform methods of numerical modeling and simulation of the separation process, which are widely used for the research of devices of this type. Using the methods of numerical simulation, the study of the cyclone with intermediate dust removal was carried out. In this cyclone, the change in the radius of the apparatus of the tangential, radial, and axial velocity components is investigated. In the course of the research, it is established that in the separation space the tangential component of velocity increases from 18–20 m/s in the upper part of the device to 22–25 m/s in the area of the lower end of the exhaust pipe, the radial component of velocity takes values from 0 to 2 m/s, and the axial component of the speed has a maximum value of 10–15 m/s. In the conical part of the apparatus the tangential component of velocity decreases from 27 m/s in the upper planes of the conical part of the apparatus to 10 m / s near the dust unloading pipe, the radial component of speed has centripetal character, the axial component of speed decreases as the gas flow to the dust unloading pipe decreases. It has been established that in the cylindrical part of the apparatus about 60 % of the gas flow volume is transferred from the downstream to the upstream by a secondary vortex, and in the conical part, about 40 % of the gas volume is transferred from the downstream to the upstream. It is shown that large values of the tangential component of velocity in the separation zone contribute to the ingress of dust particles into the annular space behind the dust unloading holes, and small values of the tangential component of velocity, axial and radial in the annular space behind the dust unloading holes has a positive effect on the operation of the dust collector.

Deep Penetration of UV Radiation into PMMA and Electron Acceleration in Long Plasma Channels Produced by 100 ns KrF Laser Pulses

Long (~1 mm), narrow (30−40 μm in diameter) corrugated capillary-like channels were produced in the axially symmetric 2D interaction regime of 100 ns KrF laser pulses with polymethylmethacrylate (PMMA) at intensities of up to 5 × 1012 W/cm2. The channels extended from the top of a deep (~1 mm) conical ablative crater and terminated in a 0.5 mm size crown-like pattern. The modeling experiments with preliminary drilled capillaries in PMMA targets and Monte Carlo simulations evidenced that the crown origin might be caused by high-energy (0.1–0.25 MeV) electrons, which are much higher than the electron temperature of the plasma corona ~100 eV. This indicates the presence of an unusual direct electron acceleration regime. Firstly, fast electrons are generated due to laser plasma instabilities favored by a long-length interaction of a narrow-band radiation with plasma in the crater. Then, the electrons are accelerated by an axial component of the electrical field in a plasma-filled corrugated capillary waveguide enhanced by radiation self-focusing and specular reflection at the radial plasma gradient, while channel ripples serve the slowing down of the electromagnetic wave in the phase with electrons.

Circumferential wall shear stress predicts co-localized progressive dilation in bicuspid aortic valve patients

Background Bicuspid aortic valve (BAV), a congenital heart defect, is associated with ascending aorta (AAo) dilation. Whether the high prevalence of dilation in BAV patients is related to alteration of aortic blood flow and thus in wall shear stress (WSS) [1,2], which have been associated with aortic wall degeneration [3], or intrinsic abnormalities of the aortic wall, such as altered aortic stiffness [4], has not been established. Recently, a technique for the semi-automatic quantification of progressive aortic dilation maps via image registration has been introduced [5]. Purpose To test whether ascending aorta WSS predicts co-localized progressive dilation in BAV patients. Methods Forty BAV patients free from moderate and severe aortic valve regurgitation (regurgitant fraction &lt;16%) and stenosis (maximum velocity at the aortic valve &lt;3m/s), with no previous aortic or aortic valve surgery or replacement and included in a double-blind clinical trial (BICATOR, NCT02679261) were enrolled. All patients underwent a baseline 4D flow CMR study to assess aortic hemodynamics, followed by two contrast-enhanced computed tomography angiographies to quantify progressive dilation. WSS was computed at 64 pre-specified standardized ascending aortic regions, automatically obtained dividing the ascending aorta into 8 equidistant longitudinal sections which were further divided along the circumference into 8 equal regions (I = inner, L = left, O = outer and R = right) [2]. WSS was also projected into axial and circumferential directions, as previously described [1,2]. Progressive dilation was assessed in terms of growth rate (GR), i.e. increase in diameter divided by follow-up duration [mm/year], following a previously described methodology [5], at the same 64 pre-specified ascending aortic locations. A two-tailed p-value &lt;0.05 was considered statistically significant. Results Demographic and clinical characteristics of the patients are shown in Table 1. WSS and growth rate maps are shown in Figure 1. Follow-up duration was 44.8±2.6 months. Growth rate (Figure 1A) was heterogeneously distributed, being highest (up to 0.26 mm/year) in the outer region of the mid AAo and in the inner region of the proximal-mid AAo. Circumferential WSS showed highest values in the outer region of the mid AAo (Figure 1C) while WSS (magnitude) and its axial component (Figure 1B and D) presented maximum values in the right region of the mid AAo. Maps of statistically significant association between GR and WSS values showed circumferential WSS to be correlated with GR in regions where progressive dilation was fastest, while WSS magnitude and its axial component resulted in limited associations with GR maps. Conclusions Circumferential wall shear stress predicts location-matched progressive dilation in bicuspid aortic valve patients. FUNDunding Acknowledgement Type of funding sources: Public grant(s) – National budget only. Main funding source(s): This study has received funding from the Instituto de Salud Carlos III (PI17/00381). Guala A. has received funding from Spanish Ministry of Science, Innovation and Universities (IJC2018-037349-I). Table 1. Demographics Figure 1. GR and WSS maps and correlations

Electric Field Distribution in HVDC Cable Joint in Non-Stationary Conditions

Accessories such as joints and terminations represent weak points in HVDC cable systems. The DC field distribution is intimately dependent on the thermal conditions of the accessory and on material properties. Moreover, there is no available method to probe charge distribution in these conditions. In this work, the field distribution in non-stationary conditions, both thermally and electrically, is computed considering crosslinked polyethylene (XLPE) as cable insulation and different insulating materials (silicone, rubber, XLPE) for a 200 kV joint assembled in a same geometry. In the conditions used, i.e., temperatures up to 70 °C, and with the material properties considered, the dielectric time constant appears of the same order or longer than the thermal one and is of several hours. This indicates that both physical phenomena need to be considered for modelling the electric field distribution. Both the radial and the tangential field distributions are analysed, and focus is given on the field distribution under the stress cone on the ground side and near the central deflector on the high voltage side of the joint. We show that the position of the maximum field varies in time in a way that is not easy to anticipate. Under the cone, the smallest tangential field is obtained with the joint insulating material having the highest electrical conductivity. This results from a shift of the field towards the cable insulation in which the geometrical features produce a weaker axial component of the field. At the level of the central deflector, it is clear that the tangential field is higher when the mismatch between the conductivity of the two insulations is larger. In addition, the field grows as a function of time under stress. This work shows the need of precise data on materials conductivity and the need of probing field distribution in 3D.

Influence of Tool Blunting on the Value of the Axial Component of the Cutting Force and the Drilling Process

One of the main technological criteria affecting the quality of drilling the holes is the correct geometry of a cutting tool and the amount of its wear. The determination of the “critical” amount of a drill wear is possible only through the indirect way, in particular by the presence of the copper foil burrs at the tool output from the printed circuit board, since with the up-to-date degree of integration of micro-assemblies, the main part of the processed holes has the diameter of about 0.6-0.8 mm, and it is quite challenging to determine the tool wear without special equipment, and in conditions of mass production it is almost impossible. A number of industrial experiments with the hard-alloy drills of standard sharpening geometry of various amount of wear was carried out in order to assess the influence of the cutting tool geometry and the amount of wear on the drilling process. To assess the quality of the processed holes, the chip size (Lch), the micro-roughness of the holes (Ra) and the size of the copper foil burrs at the output of the workpieces (Hb) were additionally measured with a specialized precision tool. In total, 1500 holes were drilled at each previously determined operating mode. The “critical” value of the tool blunting, the maximum allowable values of Lch,Ra and Hbwere practically defined in the course of work. On the basis of the conducted experiments, the threshold values of the axial feed speeds for the work of the “worn out” and “blunted” tool were defined. In addition, the general recommendations were formulated for the operator when drilling the foiled fiberglass and eliminating mass defects at printed circuit board manufacture.

Pch2 orchestrates the meiotic recombination checkpoint from the cytoplasm

During meiosis, defects in critical events trigger checkpoint activation and restrict cell cycle progression. The budding yeast Pch2 AAA+ ATPase orchestrates the checkpoint response launched by synapsis deficiency; deletion of PCH2 or mutation of the ATPase catalytic sites suppress the meiotic block of the zip1Δ mutant lacking the central region of the synaptonemal complex. Pch2 action enables adequate levels of phosphorylation of the Hop1 axial component at threonine 318, which in turn promotes activation of the Mek1 effector kinase and the ensuing checkpoint response. In zip1Δ chromosomes, Pch2 is exclusively associated to the rDNA region, but this nucleolar fraction is not required for checkpoint activation, implying that another yet uncharacterized Pch2 population must be responsible for this function. Here, we have artificially redirected Pch2 to different subcellular compartments by adding ectopic Nuclear Export (NES) or Nuclear Localization (NLS) sequences, or by trapping Pch2 in an immobile extranuclear domain, and we have evaluated the effect on Hop1 chromosomal distribution and checkpoint activity. We have also deciphered the spatial and functional impact of Pch2 regulators including Orc1, Dot1 and Nup2. We conclude that the cytoplasmic pool of Pch2 is sufficient to support the meiotic recombination checkpoint involving the subsequent Hop1-Mek1 activation on chromosomes, whereas the nuclear accumulation of Pch2 has pathological consequences. We propose that cytoplasmic Pch2 provokes a conformational change in Hop1 that poises it for its chromosomal incorporation and phosphorylation. Our discoveries shed light into the intricate regulatory network controlling the accurate balance of Pch2 distribution among different cellular compartments, which is essential for proper meiotic outcomes.

Investigating the Influence of Impeller Axial Thrust Balance Holes On the Flow and Overall Performance of a Cryogenic Liquid Turbine Expander

An excessive rotor axial thrust in any turbomachine can cause critical operational problems, and rotor axial thrust balancing has always attracted much attention. The present numerical study is focused on axial thrust balancing for a cryogenic liquid turbine expander, whose axial thrust balancing is typically challenging because of its small impeller size and large axial thrust. A computational fluid dynamics (CFD) simulation is conducted in a real turbine expander environment constituted by main and gap flow domains with allowing for the thermodynamic effect of liquefied air. The balance hole influential mechanism on the main and gap flows is explored, and its influence on the expander axial thrust and overall performance is quantified. The results show that the use of balance holes creates a highly swirling gap flow, and the static pressure over the impeller disk back-side surface decreases to produce a small axial component force and axial thrust, but the turbine expander overall efficiency drops by 1.1 and 2.8 points at 100% and 50% design flow, respectively, due to an increased internal leakage loss and distorted impeller flow. In addition, a parametric study is conducted to analyze the effect of balance hole diameter, circumferential position and radial position on expander axial thrust and overall performance. The results indicate that the axial thrust is sensitive to both the balance hole diameter and circumferential position but less sensitive to its radial position, while the overall efficiency is influenced by all three parameters.