Test Method for Determination of Decay Rates for Use in Sound Insulation Test Methods

2020 ◽  
Author(s):  
Keyword(s):  
Test Methods ◽  
Decay Rates ◽  
Test Method ◽  
Sound Insulation

Study on the Bearing Capacity Test for the Saline Soil Soft Ground

2014 ◽  
Vol 587-589 ◽  
pp. 947-951
Author(s):  
Jun Yong Liu ◽  
Liu Jun Zhang
Keyword(s):  
Bearing Capacity ◽  
Saline Soil ◽  
Test Methods ◽  
Test Method ◽  
Soft Ground ◽  
Characteristic Value ◽  
Soft Foundation

The test methods provided by current related "specifications" do not apply to saline soil soft foundation bearing capacity test. Through discussing the limitations of the related specifications and based on the experience on saline soil soft ground capacity test, the paper made some improvements of test on such aspects: conditions of loading and stopping load, determination of the characteristic value of the ground bearing capacity and evaluation, the paper also put forward the saline soil soft ground capacity test method.

scholarly journals Analysis of Vitamin A in Multivitamin Products

2021 ◽  
Vol 11 (3) ◽  
pp. 174-184
Author(s):  
A. S. Alekseeva ◽  
T. B. Shemeryankina ◽  
M. N. Lyakina ◽  
M. S. Smirnova ◽  
E. P. Fedorova ◽  
...  
Keyword(s):  
Vitamin A ◽  
High Performance ◽  
Beta Carotene ◽  
Test Methods ◽  
Retinyl Palmitate ◽  
Test Method ◽  
Medicinal Products ◽  
Retinyl Acetate ◽  
Preliminary Purification

Vitamin A is present in multivitamin products mainly in the form of retinol esters: retinyl acetate, retinyl palmitate, and beta carotene—retinol precursor (dimer) found in plants, which is capable of converting into retinol in liver cells. Retinol is determined in medicinal products primarily by high performance liquid chromatography (HPLC), with preliminary purification and vitamin isolation by liquid-liquid extraction. However, scientific literature also describes other methods of sample preparation and analysis of such compounds. An important issue is differentiation of vitamin A from other fat-soluble vitamins often included as components in multivitamin products. The aim of the study was to analyse and summarise data on current methods used for determination of vitamin A and its derivatives in medicinal products. The authors analysed the range of vitamin A products authorised in the Russian Federation, and the test methods described in their product specification files. The study demonstrated that the test method most often used for determination of retinol esters was HPLC with isocratic elution mode using octadecylsilyl packing in the reverse-phase mode, and, less frequently, aminopropylsilyl packing in the normal phase mode. Determination of beta carotene in medicinal products is most often performed using spectrophotometry. 

The modern methods of pin-type bearing test of metallic materials

2019 ◽  
Vol 85 (7) ◽  
pp. 41-49
Author(s):  
Yaroslava V. Sulimina ◽  
Nikolay O. Yakovlev ◽  
Vladimir S. Erasov ◽  
Aleksey Yu. Ampilogov ◽  
Andrey N. Polyakov ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Test Procedure ◽  
Test Methods ◽  
Test Method ◽  
Strength Characteristics ◽  
Metallic Materials ◽  
Bearing Strength ◽  
Bearing Stress ◽  
The Impact

The special features of various bearing deformation measurements for pin-type bearing tests of metallic materials are considered along with their impact on the magnitude of the «bearing elastic modulus» and bearing stress. These bearing test methods are present in ASTM and various institutional standards, though no state standard (GOST, GOST R) is currently available for bearing test method of metallic materials. Analysis of additional deformations which arise in determining the degree of hole bearing deformation is carried out. A set of sources of additional deformations is shown to be characteristic for each test procedure and is attributed to the design features of the device, the site and a way of mounting the extensometer. Additional deformations can be both tensile and compressive. It is shown that the impact of additional deformations on the «bearing elastic modulus» is limited to 14% for different procedures. No difference between the methods is revealed with regard to determination of the strength characteristics. At the same time the dispersion decreases with increase in plastic deformation and for bearing deformation about 4% the variation coefficient for all methods is no more than 1%. Advantages and shortcomings of the bearing test methods which affect the reproducibility of the results are considered. The effect of the specimen geometry on the bearing characteristics is considered. It is shown that increase both in the distance from the edge of the bearing specimen to the center of the hole for 1163T, VT6ch, 30KhGSA alloys and residual bearing deformation up to 6%, increase bearing strength characteristics.

Fan Performance Testing Using Inlet Measuring Methods

1973 ◽  
Vol 187 (1) ◽  
pp. 405-412
Author(s):  
J. Whitaker
Keyword(s):  
Flow Measurement ◽  
Performance Testing ◽  
Test Methods ◽  
Test Method ◽  
Fan Performance ◽  
Optimum Configuration ◽  
Free Discharge ◽  
Pressure Selection ◽  
Selection Of

To contend with installation variants the fan must be tested in a system that resembles its site installation. Four simplified system arrangements are covered with two inlet test methods—ducted inlet and free inlet—by adding ducts to the free discharge. With free inlet tests a plenum chamber is attached to the fan inlet in order to obtain the required measurements; investigations to provide information concerning the optimum configuration of this test method are described. Determination of static pressure, selection of inlet devices for flow measurement; simulation of inlet and outlet ducts and the method of loading are also discussed.

Hot Pin Pull Method – New Test Procedure for the Adhesion Measurement for 3D-MID

2014 ◽  
Vol 1038 ◽  
pp. 115-120 ◽  
Author(s):  
Christian Goth ◽  
Thomas Kuhn ◽  
Gerald Gion ◽  
Jörg Franke
Keyword(s):  
Test Procedure ◽  
Test Methods ◽  
Test Method ◽  
Testing System ◽  
Adhesion Test ◽  
Metallic Structures ◽  
Adhesion Measurement ◽  
Molded Interconnect Devices ◽  
Unsolved Issue

The adhesion test of metallic structures on MID (Molded Interconnect Devices) parts is an unsolved issue. So far no method really works reliably. The test methods which are conventionally used are the pull-off test and the shear-test. Both show large standard deviation and the reproducibility is not assured. Nordson DAGE has introduced the new micro-material testing system 4000Plus. This device enables a new test method for the determination of the adhesion strength of MID structures using the hot pin pull (hot bump pull) method. Copper pins (tinned or untinned) are heated up with a user defined temperature profile, soldered to a metallized structure on the MID and then removed vertically upward, while the force is recorded. In this contribution investigations with this new test method are presented.

Sign in / Sign up

Export Citation Format

Share Document