scholarly journals Strain Hardening of Low-Carbon Steel in the Area of Jerky Flow

Author(s):  
І. О Vakulenko ◽  
D. M Bolotova ◽  
S. V Proidak ◽  
B Kurt ◽  
A. E Erdogdu ◽  
...  

Purpose. The aim of this work is to assess the effect of ferrite grain size of low-carbon steel on the development of strain hardening processes in the area of nucleation and propagation of deformation bands. Methodology. Low-carbon steels with a carbon content of 0.06–0.1% C in various structural states were used as the material for study. The sample for the study was a wire with a diameter of 1mm. The structural studies of the metal were carried out using an Epiquant light microscope. Ferrite grain size was determined using quantitative metallographic techniques. Different ferrite grain size was obtained as a result of combination of thermal and termo mechanical treatment. Vary by heating temperature and the cooling rate, using cold plastic deformation and subsequent annealing, made it possible to change the ferrite grain size at the level of two orders of magnitude. Deformation curves were obtained during stretching the samples on the Instron testing machine. Findings. Based on the analysis of stretching curves of low-carbon steels with different ferrite grain sizes, it has been established that the initiation and propagation of plastic deformation in the jerky flow area is accompanied by the development of strain hardening processes. The study of the nature of increase at dislocation density depending on ferrite grain size of low-carbon steel, starting from the moment of initiation of plastic deformation, confirmed the existence of relationship between the development of strain hardening at the area of jerky flow and the area of parabolic hardening curve. Originality. One of the reasons for decrease in Luders deformation with an increase of ferrite grain size of low-carbon steel is an increase in strain hardening indicator, which accelerates decomposition of uniform dislocations distribution in the front of deformation band. The flow stress during initiation of plastic deformation is determined by the additive contribution from the frictional stress of the crystal lattices, the state of ferrite grain boundaries, and the density of mobile dislocations. It was found that the size of dislocation cell increases in proportion to the diameter of ferrite grain, which facilitates the development of dislocation annihilation during plastic deformation. Practical value. Explanation of qualitative dependence of the influence of ferrite grain size of a low-carbon steel on the strain hardening degree and the magnitude of Luders deformation will make it possible to determine the optimal structural state of steels subjected to cold plastic deformation.

2005 ◽  
Vol 475-479 ◽  
pp. 165-168 ◽  
Author(s):  
Ping Yang ◽  
Wang Yue Yang ◽  
Zu Qing Sun

Texture evolutions are determined by XRD and EBSD techniques during ferrite refinement through deformation-enhanced ferrite transformation (DEFT) and dynamic recrystallization (DREX). Evidences of transformation texture, deformation texture and recrystallization texture during DEFT are provided and compared with the texture during DREX. The influence of pass-interval during DEFT on texture is illustrated. Results are discussed in terms of the influences of ferrite grain size and deforming temperature.


2016 ◽  
Vol 879 ◽  
pp. 2528-2531
Author(s):  
Akira Yanagida ◽  
Ryo Aoki ◽  
Masataka Kobayashi

A Nb alloyed low carbon steel was processed by hot equal channel angular extrusion (ECAE) and following transformation. The workpieces were heated up to the 960°C in the furnace for 10 min within the container block. Before extrusion, the die was preheated to 400oC. The workpiece was cooled in the die after ECAE process. 1 pass and 2 pass via route C were conducted at a speed of 32mm/s, the inter-pass time is about 2 sec. The sample of average ferrite grain size of about 2μm, a tensile strength of 800MPa, a total elongation about 20% is produced after 2 pass ECAE processed and subsequent cooling.


1996 ◽  
Vol 36 (10) ◽  
pp. 1279-1285 ◽  
Author(s):  
A. Schmickl ◽  
D. Yu ◽  
C. Killmore ◽  
D. Langley ◽  
T. Chandra

2005 ◽  
Vol 475-479 ◽  
pp. 133-136 ◽  
Author(s):  
Xin Min Fan ◽  
Bosen Zhou ◽  
Lin Zhu ◽  
Heng Zhi Wang ◽  
Jie Wen Huang

In this paper, the circulation rolling plastic deformation(CRPD) surface nanocrystallization technology is proposed based on the idea that the severe plastic deformation can induce grain refinement. The equipment of CRPD is designed and manufactured. A nanocrystallization surface layer was successfully obtained in a column sample of low carbon steel. The average grain size in the top surface layer is about 18 nm, and gradually increases with the distance from the surface. The hardness increases gradually from about 200HV0.1 in the matrix to about 600HV0.1 in the surface layer.


2015 ◽  
Vol 56 (9) ◽  
pp. 57
Author(s):  
D. O. Panov ◽  
A. N. Balakhnin ◽  
A. S. Perzev ◽  
A. I. Smirnov ◽  
M. Y. Simonov

Sign in / Sign up

Export Citation Format

Share Document