scholarly journals Effects of air abrasion with alumina or glass beads on surface characteristics of CAD/CAM composite materials and the bond strength of resin cements

2015 ◽  
Vol 23 (6) ◽  
pp. 629-636 ◽  
Author(s):  
ARAO Nobuaki ◽  
YOSHIDA Keiichi ◽  
SAWASE Takashi
Keyword(s):  
Composite Materials ◽  
Bond Strength ◽  
Surface Characteristics ◽  
Glass Beads ◽  
Air Abrasion ◽  
Resin Cements ◽  
Cad Cam

scholarly journals Effects of Immediate and Delayed Cementations for CAD/CAM Resin Block after Alumina Air Abrasion on Adhesion to Newly Developed Resin Cement

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7058
Author(s):  
Akane Chin ◽  
Masaomi Ikeda ◽  
Tomohiro Takagaki ◽  
Toru Nikaido ◽  
Alireza Sadr ◽  
...  
Keyword(s):  
Bond Strength ◽  
Water Sorption ◽  
Resin Composite ◽  
Resin Cement ◽  
Air Abrasion ◽  
Resin Cements ◽  
Significant Difference ◽  
Computer Aided ◽  
Cad Cam ◽  
Curing Methods

The purpose of this study was to evaluate the effect of one week of Computer-aided design/Computer-aided manufacturing (CAD/CAM) crown storage on the μTBS between resin cement and CAD/CAM resin composite blocks. The micro-tensile bond strength (μTBS) test groups were divided into 4 conditions. There are two types of CAD/CAM resin composite blocks, namely A block and P block (KATANA Avencia Block and KATANA Avencia P Block, Kuraray Noritake Dental, Tokyo, Japan) and two types of resin cements. Additionally, there are two curing methods (light cure and chemical cure) prior to the μTBS test—Immediate: cementation was performed immediately; Delay: cementation was conducted after one week of storage in air under laboratory conditions. The effect of Immediate and Delayed cementations were evaluated by a μTBS test, surface roughness measurements, light intensity measurements, water sorption measurements and Scanning electron microscope/Energy dispersive X-ray spectrometry (SEM/EDS) analysis. From the results of the μTBS test, we found that Delayed cementation showed significantly lower bond strength than that of Immediate cementation for both resin cements and both curing methods using A block. There was no significant difference between the two types of resin cements or two curing methods. Furthermore, water sorption of A block was significantly higher than that of P block. Within the limitations of this study, alumina air abrasion of CAD/CAM resin composite restorations should be performed immediately before bonding at the chairside to minimize the effect of humidity on bonding.

Evaluation of bond strength of dual resin cements to CAD/CAM-created lithium disilicate ceramic

2020 ◽  
Vol 69 (3) ◽  
Author(s):  
Felipe Sczepanski ◽  
Cláudia R. Brunnquell ◽  
Sandrine B. Berger ◽  
Eloisa A. Paloco ◽  
Murilo B. Lopes ◽  
...  
Keyword(s):  
Bond Strength ◽  
Lithium Disilicate ◽  
Resin Cements ◽  
Cad Cam

scholarly journals Effect of elapsed time after air abrasion on bond strength of luting agent to CAD/CAM resin blocks

2019 ◽  
Vol 61 (3) ◽  
pp. 459-467
Author(s):  
Rana Asano ◽  
Shiho Otake ◽  
Kosuke Nozaki ◽  
Keiichi Yoshida ◽  
Hiroyuki Miura
Keyword(s):  
Bond Strength ◽  
Air Abrasion ◽  
Elapsed Time ◽  
Luting Agent ◽  
Cad Cam

scholarly journals Bond strength of modern self-adhesive resin cements to human dentin and different CAD/CAM ceramics

2020 ◽  
Vol 22 (2) ◽  
Author(s):  
Andrzej Małysa ◽  
Joanna Weżgowiec ◽  
Dariusz Danel ◽  
Klauss Boening ◽  
Katarzyna Walczak ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Shear Strength Test ◽  
Software Failure ◽  
Human Dentin ◽  
Cad Cam ◽  
Bond Strengths

Purpose: The aim of the study was to evaluate the shear bond strength of CAD/CAM ceramics to dentin after cementation with conventional or self-adhesive resin cements. Methods: Three self-adhesive, self-etching cements (Panavia SA, RelyX U200, Maxcem Elite), and one conventional cement (Panavia V5), were selected to lute three CAD/CAM ceramics (IPS Empress CAD, IPS e.max CAD, IPS e.max ZirCAD) onto the dentin. The bond strength was evaluated using a shear strength test according to the PN-EN ISO 29022:2013-10. Evaluation of the differences was performed using the Statistica software. Failure modes were analyzed using a light microscope. Results: All the studied cements differed (regardless of the ceramic type) in the bond strength. The highest bond strength was observed in Panavia V5, lower – in RelyX U200 and Panavia SA, and the lowest – in Maxcem. For IPS e.max ZirCAD, it was observed that compared to Panavia V5, the other cements were characterized by a significantly higher bond strength. For the IPS Empress CAD and the IPS e.max CAD, Panavia V5 displayed the highest bond strength. For all the studied self-adhesive cements, the failure of adhesion between the cement and dentin was predominant mode. Conclusions: Significant differences were found in the shear bond strengths of the CAD/CAM ceramics luted to dentin using tested self-adhesive and conventional cements. The bond strength depended on the combination of ceramic and cement. The IPS e.max ZirCAD had the highest bond strength to dentin after cementation with RelyX U200, while the IPS Empress CAD and IPS e.max CAD – with Panavia V5.

Effect of Different Adhesive Strategies and Time on Microtensile Bond Strength of a CAD/CAM Composite to Dentin

2019 ◽  
Vol 44 (3) ◽  
pp. 262-272
Author(s):  
EM Meda ◽  
RN Rached ◽  
SA Ignácio ◽  
IA Fornazari ◽  
EM Souza
Keyword(s):  
Bond Strength ◽  
Computer Aided Design ◽  
Optical Microscope ◽  
Single Bond ◽  
Microtensile Bond Strength ◽  
Resin Cements ◽  
Bonding Agents ◽  
Etch And Rinse ◽  
Computer Aided ◽  
Cad Cam

SUMMARY Purpose: The aim of this study was to evaluate the effect of adhesive strategy and time on the microtensile bond strength of a computer-aided design/computer-aided manufacturing (CAD/CAM) composite to dentin. Methods and Materials: Sixty CAD/CAM composite blocks were bonded to human dentin with simplified bonding agents using etch-and-rinse and self-etching approaches and amine-based and amine-free resin cements, with and without the application of a dual-cure activator (DCA; n=10): SBP-ARC (Adper Single Bond Plus + RelyX ARC), SBP-RXU (Adper Single Bond Plus + RelyX Ultimate), SBP-DCA-RXU (Adper Single Bond Plus + DCA + RelyX Ultimate), SBU-ARC (Scotchbond Universal + RelyX ARC), SBU-RXU (Scotchbond Universal + RelyX Ultimate), and SBU-DCA-ARC (Scotchbond Universal + DCA + RelyX ARC). Each specimen was light cured for 40 seconds under load and stored in distilled water at 37°C for seven days. Stick-shaped specimens (1.0 mm2) were obtained. Half of the specimens underwent microtensile bond strength testing, and the other half were subjected to the same tests after six months of storage. Failure mode was determined using an optical microscope (40×). The data were analyzed by a two-way analysis of variance followed by the Games-Howell test and Student t-test (preset alpha of 0.05). Results: After seven days, SBU-RXU presented the highest mean bond strength, statistically different from only SBU-ARC (p<0.05). Most of the groups exhibited a statistically significant reduction in bond strength after 6 months (p<0.05), except SBP-RXU and SBU-ARC (p>0.05). Conclusion: The adhesive strategy, with different associations between adhesive systems and resin cements, as well as the use of a DCA, affected the bond strength of both amine-free and amine-based resin cements to a CAD/CAM composite.

scholarly journals Microtensile bond strength of CAD/CAM-fabricated polymer-ceramics to different adhesive resin cements

2018 ◽  
Vol 43 (4) ◽  
Author(s):  
Leyla Sadighpour ◽  
Farideh Geramipanah ◽  
Zahra Ghasri ◽  
Mehrnoosh Neshatian
Keyword(s):  
Bond Strength ◽  
Microtensile Bond Strength ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Cad Cam
Sign in / Sign up

Export Citation Format

Share Document