scholarly journals Bond strength of a composite resin to glass ionomer cements using different adhesive systems

2017 ◽  
Vol 46 (4) ◽  
pp. 214-219
Author(s):  
Ana Carolina de Oliveira BECCI ◽  
Mônica de Souza BENETTI ◽  
Natália Bertolo DOMINGUES ◽  
Elisa Maria Aparecida GIRO
Keyword(s):  
Bond Strength ◽  
Composite Resin ◽  
Glass Ionomer Cement ◽  
Adhesive System ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Single Bond ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Significant Difference

Abstract Introduction Glass ionomer cements are often used as a base or cavity lining prior to restorative material. Objective To evaluate the bond strength of a composite resin to different glass ionomer cements, when using a two-step conventional and self-etching adhesive systems. Material and method Three glass ionomer cements (Ketac Molar Easymix, Vitremer and Vitrebond), the composite resin Filtek Z350 XT and the adhesive systems Adper Single Bond 2, Clearfil SE Bond and Adper Easy One were used. As negative control, resin was bonded to cement without using an adhesive system. Holes (4 mm diameter, 2 mm deep) prepared in acrilic bloks were filled with the glass ionomer cements (n=12/group). On the surface, an area of 1mm in diameter was delimited, the adhesive system was applied, and a specimen of composite resin with 1 mm height was made. After 24 hours storage (37 °C and 100% humidity), the microshear test was performed. Data were analyzed using two-way ANOVA and Tukey test for comparison between groups (α=0.05). Result The adhesive systems significantly improved the bond strenght of composite resin to glass ionomer cements (p≤0.001). There was no significant difference in bond strength when self-etching adhesive systems were compared with the simplified etch-and-rinse adhesive, except for Vitrebond where Clearfil SE Bond determined higher bond strength when compared to Adper Single Bond 2 (p=0.003). Conclusion Self-etching adhesive systems are a good option for establishing the bond between the composite resin and the glass ionomer cement.

scholarly journals Effect Of Chitosan Treatment On Shear Bond Strength Of Composite To Deep Dentin Using Self-Etch And Total-Etch Adhesive Systems

2021 ◽  
Vol 24 (2) ◽  
Author(s):  
Fateme Vasei ◽  
Farahnaz Sharafeddin
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Adhesive System ◽  
Single Bond ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Self Etch

Objective: To assess the shear bond strength (SBS) of resin composite to deep dentin, using 1 and 2.5% chitosan pretreatment as well as different adhesive systems. Material and Methods: 80 human maxillary molars were randomly divided to eight groups according to the type of adhesive system and dentin pretreatment (n = 10): I) two-step self-etch system (Clearfil SE bond); II) two-step etch-andrinse system (Adper single bond 2); III) 2.5% chitosan + Clearfil SE bond; IV) 2.5% chitosan +etch + Adper single bond 2; V) etch + 2.5% chitosan + Adper single bond 2; VI) 1% chitosan + Clearfil SE bond; VII) 1% chitosan + etch + Adper single bond 2; VIII) etch + 1% chitosan + Adper single bond 2 (chitosan solution (w/v): 2.5 g and 1 g of chitosan (Sigma Aldrich, USA) was dissolved in 100 ml of 1% acetic acid). Plastic molds were positioned on dentin and filled with composite (Z350, 3M ESPE, USA). SBS (MPa) was tested using a universal testing machine. ANOVA tests, Tukey’s test, and independent t test were used to analyze data (p < 0.05). Results: The highest SBS value among self-etch groups was observed with 1% chitosan (p = 0.001). In the etch-and-rinse group, the SBS of 1% chitosan was significantly lower than the other groups. Chitosan treatment following acid etching led to higher SBS in comparison to when chitosan was applied before etching, with the significant difference in 1% concentration (p = 0.030). A predominance of mix fractures was observed in dentin. Conclusion: Improved dentin bond strength can be achieved through immediate dentin pretreatment with 1% chitosan in self-etch adhesive systems. Chitosan Pretreatment may not be advantageous for etch-and-rinse adhesive systems. Keywords Adhesive system; Chitosan; Deep dentin; Shear strength.

scholarly journals Shear Bond Strength of Two Adhesive Materials to Eroded Enamel

2013 ◽  
Vol 14 (4) ◽  
pp. 700-703 ◽  
Author(s):  
Daniela Hesse ◽  
Tathiane Lenzi ◽  
Camila Guglielmi ◽  
Ketlin Anacleto ◽  
Daniela Prócida Raggio
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Glass Ionomer Cement ◽  
Adhesive System ◽  
Glass Ionomer ◽  
Single Bond ◽  
Etch And Rinse ◽  
Resin Modified Glass Ionomer ◽  
Ionomer Cement ◽  
Adhesive Materials

ABSTRACT Aim To evaluate the bond strength of one etch-and-rinse adhesive system and one resin-modified glass ionomer cement to sound and eroded enamel. Materials and methods Forty-eight bovine incisors were embedded in acrylic resin and ground to obtain flat buccal enamel surfaces. Half of the specimens were submitted to erosion challenge with pH-cycling model (3x/cola drink for 7 days) to induce eroded enamel. After that, all specimens were randomly assigned according to adhesive material: etch-andrinse adhesive system (Adper Single Bond 2 – 3M ESPE, USA) or resin-modified glass ionomer cement (Vitro Fil LC – DFL, Brazil). The shear bond testing was performed after 24 hours water storage (0.5 mm/min). Shear bond strength means were analyzed by two-way ANOVA and Tukey post hoc tests (p < 0.05). Results Adper Single Bond 2 showed the highest bond strength value to eroded enamel (p < 0.05), whereas no difference was observed in sound enamel compared with Vitro Fil LC (p > 0.05). Conclusion Bond strength of etch-and-rinse adhesive system increases in eroded enamel, while no difference is verified to resin-modified glass ionomer cement. Clinical significance Adhesive materials may be used in eroded enamel without jeopardizing the bonding quality; however it is preferable to use etch-and-rinse adhesive system. How to cite this article Lenzi T, Hesse D, Guglielmi C, Anacleto K, Raggio DP. Shear Bond Strength of Two Adhesive Materials to Eroded Enamel. J Contemp Dent Pract 2013;14(4):700-703.

scholarly journals Co-Blend Application Mode of Bulk Fill Composite Resin

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2504
Author(s):  
Mohammad Al-Nabulsi ◽  
Alaa Daud ◽  
Cynthia Yiu ◽  
Hanan Omar ◽  
Salvatore Sauro ◽  
...  
Keyword(s):  
Bond Strength ◽  
Composite Resin ◽  
Degree Of Conversion ◽  
Adhesive Systems ◽  
Bonding Agents ◽  
Force Microscopy ◽  
Flowable Composite ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Nanoindentation Hardness

Objective: To evaluate the effect of a new application method of bulk-fill flowable composite resin material on bond-strength, nanoleakage, and mechanical properties of dentine bonding agents. Materials and methods: Sound extracted human molars were randomly divided into: manufacturer’s instructions (MI), manual blend 2 mm (MB2), and manual blend 4 mm (MB4). Occlusal enamel was removed and flattened, dentin surfaces were bonded by Prime & Bond universal (Dentsply and Optibond FL, Kerr). For the MI group, adhesives were applied following the manufacturer’s instructions then light-cured. For MB groups, SDR flow+ bulk-fill flowable composite resin was applied in 2- or 4-mm increment then manually rubbed by a micro brush for 15 s with uncured dentine bonding agents and the mixture was light-cured. Composite buildup was fabricated incrementally using Ceram.X One, Dentsply nanohybrid composite resin restorative material. After 24-h water storage, the teeth were sectioned to obtain beams of about 0.8 mm2 for 24-h and thermocycled micro-tensile bond strength at 0.5 mm/min crosshead speed. Degree of conversion was evaluated with micro-Raman spectroscopy. Contraction gaps at 24 h after polymerization were evaluated and atomic force microscopy (AFM) nano-indentation processes were undertaken for measuring the hardness across the interface. Depth of resin penetration was studied using a scanning electron microscope (SEM). Bond strength data was expressed using two-way ANOVA followed by Tukey’s test. Nanoindentation hardness was separately analyzed using one-way ANOVA. Results: Factors “storage F = 6.3” and “application F = 30.11” significantly affected the bond strength to dentine. For Optibond FL, no significant difference in nanoleakage was found in MI/MB4 groups between baseline and aged specimens; significant difference in nanoleakage score was observed in MB2 groups. Confocal microscopy analysis showed MB2 Optibond FL and Prime & Bond universal specimens diffusing within the dentine. Contraction gap was significantly reduced in MB2 specimens in both adhesive systems. Degree of conversion (DC) of the MB2 specimens were numerically more compared to MS1 in both adhesive systems. Conclusion: Present study suggests that the new co-blend technique might have a positive effect on bond strengths of etch-and-rinse adhesives to dentine.

scholarly journals Effect of one-bottle adhesive systems on the fluoride release of a resin-modified glass ionomer

2004 ◽  
Vol 12 (1) ◽  
pp. 12-17 ◽  
Author(s):  
Linda Wang ◽  
Marília Afonso Rabelo Buzalaf ◽  
Maria Teresa Atta
Keyword(s):  
Statistical Difference ◽  
Glass Ionomer Cement ◽  
Adhesive System ◽  
Fluoride Release ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Adhesive Systems ◽  
Resin Modified Glass Ionomer ◽  
The One ◽  
In The Beginning

A dhesive systems associated to resin-modified glass ionomer cements are employed for the achievement of a higher bond strength to dentin. Despite this benefit, other properties should not be damaged. This study aimed at evaluating the short-time fluoride release of a resin-modified glass ionomer cement coated with two one-bottle adhesive systems in a pH cycling system. Four combinations were investigated: G1: Vitremer (V); G2: Vitremer + Primer (VP); G3: Vitremer + Single Bond (VSB) and G4: Vitremer + Prime & Bond 2.1 (VPB). SB is a fluoride-free and PB is a fluoride-containing system. After preparation of the Vitremer specimens, two coats of the selected adhesive system were carefully applied and light-cured. Specimens were immersed in demineralizing solution for 6 hours followed by immersion in remineralizing solution for 18 hours, totalizing the 15-day cycle. All groups released fluoride in a similar pattern, with a greater release in the beginning and decreasing with time. VP showed the greatest fluoride release, followed by V, with no statistical difference. VSB and VPB released less fluoride compared to V and VP, with statistical difference. Regardless the one-bottle adhesive system, application of coating decreased the fluoride release from the resin-modified glass ionomer cements. This suggests that this combination would reduce the beneficial effect of the restorative material to the walls around the restoration.

scholarly journals Microshear Bond Strength of Different Adhesive Systems to Dentin

2019 ◽  
Author(s):  
Sara Valizadeh ◽  
Aida Moradi ◽  
Mansooreh Mirazei ◽  
Hooman Amiri ◽  
Mohammad Javad Kharazifard
Keyword(s):  
Bond Strength ◽  
Testing Machine ◽  
Single Bond ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Microshear Bond Strength ◽  
Self Etch ◽  
Composite Cylinders

Objectives: The aim of this study was to compare the microshear bond strength (µSBS) of various adhesive systems to dentin. Materials and Methods: In this in vitro experimental study, 60 sound human third molars were divided into four groups. Dentin discs were prepared of middle-third dentin measuring 4 mm in diameter and 2 mm in thickness. Dentin surfaces were bonded with one of the four types of adhesives: (A) Single Bond (3M ESPE), Scotchbond Universal (3M ESPE) in etch and rinse (B) and self-etch (C) modes and (D) Clearfil SE Bond (Kuraray Noritake Dental). After the application of adhesive systems according to the manufacturers’ instructions, composite cylinders (Vit-l-escence) were bonded to dentin surfaces. The μSBS test was performed using a universal testing machine at a crosshead speed of 1 mm/min. Data were analyzed with one-way ANOVA and Tukey’s test (α=0.05). Results: The µSBS was the highest in self-etch Scotchbond Universal (15.8±6.08 MPa) followed by Clearfil SE Bond (15.24±4.6 MPa), etch and rinse Scotchbond Universal (11.68±4.07MPa) and Single Bond (11.24±3.74 MPa). A significant difference was only found between Single Bond and etch and rinse Scotchbond Universal groups (P=0.04). Conclusion: Based on the results of this study, application of Scotchbond Universal in self-etch mode provides a reliable bond to dentin.

scholarly journals Microshear Bond Strength of Different Adhesive Systems to Dentin

2019 ◽  
Author(s):  
Sara Valizadeh ◽  
Aida Moradi ◽  
Mansooreh Mirazei ◽  
Hooman Amiri ◽  
Mohammad Javad Kharazifard
Keyword(s):  
Bond Strength ◽  
Testing Machine ◽  
Single Bond ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Microshear Bond Strength ◽  
Self Etch ◽  
Composite Cylinders

Objectives: The aim of this study was to compare the microshear bond strength (µSBS) of various adhesive systems to dentin. Materials and Methods: In this in vitro experimental study, 60 sound human third molars were divided into four groups. Dentin discs were prepared of middle-third dentin measuring 4 mm in diameter and 2 mm in thickness. Dentin surfaces were bonded with one of the four types of adhesives: (A) Single Bond (3M ESPE), Scotchbond Universal (3M ESPE) in etch and rinse (B) and self-etch (C) modes and (D) Clearfil SE Bond (Kuraray Noritake Dental). After the application of adhesive systems according to the manufacturers’ instructions, composite cylinders (Vit-l-escence) were bonded to dentin surfaces. The μSBS test was performed using a universal testing machine at a crosshead speed of 1 mm/min. Data were analyzed with one-way ANOVA and Tukey’s test (α=0.05). Results: The µSBS was the highest in self-etch Scotchbond Universal (15.8±6.08 MPa) followed by Clearfil SE Bond (15.24±4.6 MPa), etch and rinse Scotchbond Universal (11.68±4.07MPa) and Single Bond (11.24±3.74 MPa). A significant difference was only found between Single Bond and etch and rinse Scotchbond Universal groups (P=0.04). Conclusion: Based on the results of this study, application of Scotchbond Universal in self-etch mode provides a reliable bond to dentin.

scholarly journals Effect of Different Adhesion Protocols on the Shear Bond Strength of Universal Adhesive Systems to Sound and Artificial Caries-Affected Dentin

2021 ◽  
Author(s):  
Omnia M. Sami ◽  
Essam A. Naguib ◽  
Rasha H. Afifi ◽  
Shaymaa M. Nagi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Resin Composite ◽  
Single Bond ◽  
Adhesive Systems ◽  
Universal Adhesive ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Self Etch

Abstract Objective Bonding to different dentin substrates influences resin composite restoration outcomes. This study investigated the influence of different adhesion protocols on the shear bond strength of universal adhesive systems to sound and artificial caries-affected dentin (CAD). Materials and Methods Occlusal enamel of 80 premolars were wet grinded to obtain flat midcoronal dentin. Specimens were equally divided according to the substrate condition: sound and CAD by subjecting to pH-cycling for 14 days. Each dentin substrate was bonded with the adhesive systems used in this study: Single Bond universal adhesive or Prime&Bond universal (applied either in etch-and-rinse or self-etch adhesion protocol). Adhesive systems were utilized according to manufacturers’ instructions, then resin composite was built up. Specimens were tested for shear bond strength. The data were analyzed by three-way analysis of variance, and failure modes were determined using stereomicroscope. Results There was no statistically significant difference between the two tested adhesive systems on artificially created CAD with different adhesion protocols. On sound dentin, Single Bond universal, either in the etch-and-rinse or self-etch adhesion protocols, revealed higher statistically significant shear bond strength mean values compared with CAD. Conclusion Single Bond universal adhesive in an etch-and-rinse adhesion protocol improved only bonding to sound dentin, while no added positive effect for the etching step with Prime&Bond universal adhesive was found when bonded to both sound and CAD substrates. The influence of CAD on the performance of the universal adhesives was material-dependent.

scholarly journals Morphological characterization of the tooth/adhesive interface

2006 ◽  
Vol 17 (3) ◽  
pp. 179-185 ◽  
Author(s):  
Sandra Kiss Moura ◽  
José Fortunato Ferreira Santos ◽  
Rafael Yagüe Ballester
Keyword(s):  
Composite Resin ◽  
Morphological Characteristics ◽  
Adhesive System ◽  
Morphological Characterization ◽  
Single Bond ◽  
Third Molars ◽  
Adhesive Systems ◽  
Adhesive Interface ◽  
Etch And Rinse

The purpose of this study was to assess the morphological characteristics of the tooth/adhesive interface using different adhesive systems in MOD restorations under scanning electron microscopy (SEM). The tested hypothesis was that the morphology of the bonding interface would vary in different areas of MOD restorations for the three adhesive systems. MOD cavities were prepared in 12 sound extracted human third molars and restored with Filtek Z250 composite resin and one of the following adhesive systems: Experimental ABF (n=4), Clearfil SE Bond (n=4) self-etching primers and Single Bond etch-and-rinse adhesive system (n=4). After 24-h storage in distilled water at 37ºC, teeth were sectioned and prepared for SEM. The interfacial morphology varied depending on the adhesive system and also on the evaluated area. The null hypothesis was accepted because the morphology of the tooth/adhesive interface reflected the characteristics of both the dental substrate and the adhesive systems.

scholarly journals Bond strength between silorane-based composite resin and dentin substrate

2013 ◽  
Vol 1 (4) ◽  
pp. 328
Author(s):  
Jefferson Ricardo Pereira ◽  
Lindomar Côrrea Junior ◽  
Mauro De Souza Almeida ◽  
Accácio Lins do Valle ◽  
Saulo Pamato ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Adhesive System ◽  
Strength Test ◽  
Single Bond ◽  
Tukey Test ◽  
Group 4 ◽  
Significant Difference ◽  
Group 1

The aim of this study was to evaluate the bond strength between composite resin and dentin using different bond systems. Sixteen human molars extracted were selected. Each tooth was vertically cut in 3 dentin fragments of 2 mm of thickness (n=42) and randomly divided among the groups. Groups 1 was used Adper Single Bond 2, for groups 2 Silorano primer, groups 3 Adper SE Plus, and 4 Scotchbond Multiuse. Two composite resin cylinders were built up on each dentin surface (n=10) and subjected to a micro shear bond strength test until failure. To evaluated the results were used the Kruskal-Wallis OneWay Analysis of Variance and Tukey Test (p=0.05). Kruskal-Wallis test evidenced at least one statistical significant difference (p=0.001). The Tukey test showed statistical significant differences among the group (P<0.05). Group 1 showed statically significant higher results when compared with group 4. The results of this study evidenced that the adhesive system can effect the bond strength between silorano-based composite resin and dentin.

Sign in / Sign up

Export Citation Format

Share Document