Heat Transfer Enhancement Characteristics for Falling-Film Evaporation on Horizontal Enhanced Tubes with Aqueous LiBr Solution

1999 ◽  
Vol 6 (1) ◽  
pp. 61-69 ◽  
Author(s):  
DongKwan Kim ◽  
Moo Hwan Kim
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Falling Film ◽  
Transfer Enhancement ◽  
Film Evaporation ◽  
Libr Solution ◽  
Enhanced Tubes ◽  
Falling Film Evaporation

Falling Film Evaporation of Water on Horizontal Configured Tube Bundles

2010 ◽  
Author(s):  
Wei Li ◽  
Xiaoyu Wu ◽  
Zhong Luo
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Inlet Temperature ◽  
Falling Film ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Film Evaporation ◽  
Tube Bundles ◽  
Falling Film Evaporation

This paper reports an experimental study on falling film evaporation of water on 6-row horizontal configured tube bundles in a vacuum. Three types of configured tubes, Turbo-CAB-19fpi and −26fpi, Korodense, including smooth tubes for reference, were tested in a range of film Reynolds number from about 10 to 110. Results show that as the falling film Reynolds number increases, falling film evaporation goes from tubes partial dryout regime to fully wet regime; the mean heat transfer coefficients reach peak values in the transition point. Turbo-CAB tubes have the best heat transfer enhancement of falling film evaporation in both regimes, but Korodense tubes’ overall performances are better when tubes are fully wet. The inlet temperature of heating water has hardly any effects on the heat transfer, but the evaporation pressure has controversial effects. A correlation with errors within 10% was also developed to predict the heat transfer enhancement capacity.

scholarly journals Heat Transfer Enhancement of Falling Film Evaporation on a Horizontal Tube by Thermal Spray Coating

2020 ◽  
Vol 10 (5) ◽  
pp. 1632 ◽  
Author(s):  
Tsutomu Ubara ◽  
Hitoshi Asano ◽  
Katsumi Sugimoto
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Enhancement ◽  
Spray Coating ◽  
Horizontal Tube ◽  
Thermal Spray Coating ◽  
Falling Film ◽  
Transfer Enhancement ◽  
Film Evaporation ◽  
Falling Film Evaporation

Falling film evaporators are gaining popularity as substitutes to typical flooded evaporators because of their low refrigerant charge. It is important to form and keep a thin liquid film on the heat transfer surface to ensure their high heat transfer performance. In this study, as a heat transfer enhancement surface, a fine porous surface processed using thermal spray coating was applied to a smooth copper tube with an outer diameter of 19.05 mm. Heat transfer coefficients of falling film evaporation on a single horizontal tube were experimentally evaluated using the HFC-134a refrigerant. The experiments were performed at a saturation temperature of 20 °C with the heat flux ranging from 10 to 85 kW·m−2 and for film Reynolds numbers up to 673. The study aimed to clarify the effect of the coating on the heat transfer characteristics of falling film evaporation. The results revealed that the coating could suppress partial dry out and enhance nucleate boiling in the falling film. The maximum heat transfer enhancement factor was 5.2 in the experimental range. It was further noted that the effect of the coating was especially strong under a low heat flux condition.

Numerical Simulation of the Liquid Flowing and Heat-Transfer outside the Tube of the Horizontal-Tube Falling Film Evaporator

2012 ◽  
Vol 614-615 ◽  
pp. 296-300 ◽  
Author(s):  
Wei Kang Hu ◽  
Li Yang ◽  
Lei Hong Guo
Keyword(s):  
Heat Transfer ◽  
Horizontal Tube ◽  
Water Desalination ◽  
Falling Film ◽  
Transfer Enhancement ◽  
Film Evaporation ◽  
Film Evaporator ◽  
Spray Density ◽  
Performance Of Heat Transfer ◽  
Falling Film Evaporation

This paper mainly studies the falling film evaporator in the field of water desalination. Using the method of fluent simulates the process of the liquid flowing and heat-transfer on the horizontal-tube falling film evaporation. The author analyses the distribution of the liquid film, and obtain the rule that spray density, evaporation temperature, temperature difference and pipe diameter affect the performance of heat-transfer in a certain range. So the paper plays a guiding role in heat transfer enhancement in the falling film evaporator.

Heat Transfer and Fouling Performance During Falling Film Evaporation in Vertical Porous Tubes

2020 ◽  
Author(s):  
Lei Wang ◽  
Weiyu Tang ◽  
Limin Zhao ◽  
Wei Li
Keyword(s):  
Heat Transfer ◽  
Stainless Steel ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Smooth Tube ◽  
Outer Diameter ◽  
Falling Film ◽  
Film Evaporation ◽  
Falling Film Evaporation ◽  
The Heat Transfer Coefficient

Abstract An experimental investigation was conducted on falling film evaporation along two porous tubes, which were sintered by stainless-steel powder with a diameter of 0.45 and 1 um, respectively. The test section is a 2 m long sintered tube with an outer diameter of 25 mm and a wall thickness of 2 mm. During the experiment, the pressure inside the tube was maintained at 1 atm, the inlet temperature was 373 K, and mass flux ranged from 0.51 to 1.36 kg/ (m s). Conditions of the steam outside the pipe, which was the heat source, were fixed, while the fouling tests were carried out at a constant mass flow of 0.74 kg/ (m s) using high-concentration brine as work fluid. The overall heat transfer coefficient under different working conditions was tested and compared with the stainless steel smooth tube of the same dimensions. The heat transfer coefficient of the two porous stainless tubes are about 35% and 20% lower than that of the smooth one, showing an inferior effect because the steam in the pores of the pipe wall during the infiltration process will reduce the heat conductivity. The heat transfer coefficient of the smooth tube deteriorated severely due to the deposition of calcium carbonate, which had little effect on the sintered tubes. Besides, the fouling weight of porous tubes is 2.01 g and 0 g compared with 5.52 g of the smooth tube.

Sign in / Sign up

Export Citation Format

Share Document