scholarly journals Three-dimensional contact stresses of a slick solid rubber tyre on a rigid surface

2021 ◽  
Vol 63 (3) ◽  
pp. 1-12
Author(s):  
M De Beer ◽  
Y Van Rensburg ◽  
J W Maina
Keyword(s):  
Asphalt Concrete ◽  
Three Dimensional ◽  
Contact Stresses ◽  
Full Scale ◽  
Portland Cement Concrete ◽  
Contact Patch ◽  
Linear Elastic ◽  
Concrete Base ◽  
Mass Load ◽  
Contact Shape

The main aim of this paper is to quantify the three-dimensional contact stresses imposed by a single slow-moving (or rolling) slick solid rubber tyre on a relatively rough contact surface, such as stiff asphalt concrete or airport concrete surfacing layers. The results indicated the tyre-contact patch of a slick solid rubber tyre to be of rectangular shape for a vertical tyre loading range between 20 kN and 100 kN. The rectangular tyre contact shape was confirmed with static paper prints, as well as an electronically measured contact patch with the stress-in-motion pad device. The study included load calibration using a mass load scale, and a stress-in-motion device. These were used with an existing full-scale accelerated pavement test device, referred to as the heavy vehicle simulator. In addition, simplistic multi-layer linear elastic modelling was used to quantify differences between stress and strain responses of two types of two relatively 'stiff' based pavements, such as an asphalt concrete base and Portland cement concrete base, on similar subbase and subgrade layers. Notable differences were obtained, which could potentially influence further detailed studies on the performance of full-scale slick solid rubber tyres on typical multi-layered pavements.

scholarly journals Homogeneity Assessment of Asphalt Concrete Base in Terms of a Three-Dimensional Air-Launched Ground Penetrating Radar

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1398
Author(s):  
Xiaomeng Zhang ◽  
Wenyang Han ◽  
Luchuan Chen ◽  
Zhengchao Zhang ◽  
Zhichao Xue ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Ground Penetrating Radar ◽  
Asphalt Concrete ◽  
Prediction Models ◽  
Three Dimensional ◽  
Dielectric Constants ◽  
Point Method ◽  
Concrete Base ◽  
Homogeneity Assessment ◽  
Ground Penetrating

Obtaining the required homogeneity, including uniform thickness and density, is very crucial for controlling the quality of flexible asphalt layers. Although non-destructive testing (NDT) methods are time-saving and less labor-intensive, they only provide indirect measurement data under testing area conditions and strongly depend on the explanations by prediction models. In this study, in terms of the three-dimensional air-launched Ground Penetrating Radar (GPR) technique, the dielectric constant of asphalt concrete base with dry conditions in pavements was detected and calculated by different methods (the Coring Method, Reflection Amplitudes Method and Common Mid-Point Method). According to the calculated dielectric constant, the thickness and density of asphalt concrete base were further calculated and assessed. Comparing with the Coring Method, the Common Mid-Point Method was recommended to calculate dielectric constants in order to obtain reliable thickness of asphalt pavement base. Among the Birefringence, Boettcher, Linearity indicator, and Rayleigh models, the Rayleigh model was suggested to predict the density, and the predicted density exhibited a good correlation coefficient with the measured one. Furthermore, by choosing these proper calculation methods, an assessment was successfully conducted to evaluate homogeneity of a constructed field pavement in practice.

Contact Stresses Between Elastic Cylinders: A Comprehensive Theoretical and Experimental Approach

1981 ◽  
Vol 103 (1) ◽  
pp. 40-45 ◽  
Author(s):  
M. J. Hartnett ◽  
J. W. Kannel
Keyword(s):  
Experimental Approach ◽  
Three Dimensional ◽  
Contact Stresses ◽  
Linear Elastic ◽  
Theoretical Predictions ◽  
Elastic Cylinders ◽  
Force Displacement ◽  
Contact Pressures ◽  
Two Bodies ◽  
Theory And Experiments

The purpose of the paper has been to present a comparison of theoretical predictions and experimental data for contact stresses between two bodies lubricated in contact. The theoretical analysis is based on a three-dimensional linear elastic solution to the problem and combines Boussinesq force-displacement relationships for a half-space with a modified flexibility method. The experimental approach involves the direct measurement of contact pressures between profiled rollers using a thin-film pressure transducer. Pressure measurements and predictions were made for three roller designs under various conditions of loads and misalignments. The agreement between theory and experiments is very good.

Thermomechanical Coupling of a Hyper-viscoelastic Truck Tire and a Pavement Layer and its Impact on Three-dimensional Contact Stresses

2021 ◽  
pp. 036119812110171
Author(s):  
Angeli Jayme ◽  
Imad L. Al-Qadi
Keyword(s):  
Contact Stress ◽  
Contact Area ◽  
Three Dimensional ◽  
Interaction Model ◽  
Rolling Resistance ◽  
Contact Stresses ◽  
Thermomechanical Coupling ◽  
Temperature Profiles ◽  
Near Surface ◽  
Truck Tire

A thermomechanical coupling between a hyper-viscoelastic tire and a representative pavement layer was conducted to assess the effect of various temperature profiles on the mechanical behavior of a rolling truck tire. The two deformable bodies, namely the tire and pavement layer, were subjected to steady-state-uniform and non-uniform temperature profiles to identify the significance of considering temperature as a variable in contact-stress prediction. A myriad of ambient, internal air, and pavement-surface conditions were simulated, along with combinations of applied tire load, tire-inflation pressure, and traveling speed. Analogous to winter, the low temperature profiles induced a smaller tire-pavement contact area that resulted in stress localization. On the other hand, under high temperature conditions during the summer, higher tire deformation resulted in lower contact-stress magnitudes owing to an increase in the tire-pavement contact area. In both conditions, vertical and longitudinal contact stresses are impacted, while transverse contact stresses are relatively less affected. This behavior, however, may change under a non-free-rolling condition, such as braking, accelerating, and cornering. By incorporating temperature into the tire-pavement interaction model, changes in the magnitude and distribution of the three-dimensional contact stresses were manifested. This would have a direct implication on the rolling resistance and near-surface behavior of flexible pavements.

Finite Element Simulation of a Strong-Post W-Beam Guardrail System

SIMULATION ◽  
2002 ◽  
Vol 78 (10) ◽  
pp. 587-599 ◽  
Author(s):  
Ali O. Atahan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Full Scale ◽  
Nonlinear Finite Element ◽  
Crash Test ◽  
Original Design ◽  
Dynamic Interactions ◽  
Crash Testing ◽  
Element Simulation ◽  
Test Requirements

Computer simulation of vehicle collisions has improved significantly over the past decade. With advances in computer technology, nonlinear finite element codes, and material models, full-scale simulation of such complex dynamic interactions is becoming ever more possible. In this study, an explicit three-dimensional nonlinear finite element code, LS-DYNA, is used to demonstrate the capabilities of computer simulations to supplement full-scale crash testing. After a failed crash test on a strong-post guardrail system, LS-DYNA is used to simulate the system, determine the potential problems with the design, and develop an improved system that has the potential to satisfy current crash test requirements. After accurately simulating the response behavior of the full-scale crash test, a second simulation study is performed on the system with improved details. Simulation results indicate that the system performs much better compared to the original design.

Performance Based Evaluation of Bridge Substructure in North Mississippi Using Nonlinear FEM and Field Vibration Measurement

2000 ◽  
Author(s):  
Chris L. Mullen ◽  
Prabin R. Tuladhar
Keyword(s):  
Finite Element ◽  
Transfer Functions ◽  
Response Spectrum ◽  
Three Dimensional ◽  
Vibration Measurement ◽  
Elastic Behavior ◽  
Evaluation Procedure ◽  
Vibration Measurements ◽  
Linear Elastic ◽  
Performance Based Evaluation

Abstract Discussion of a Performance - Based Engineering evaluation procedure for an existing interstate highway bridge in north Mississippi. The bridge is in a highly trafficked location near the Memphis Metropolitan area and is reflective of modern design practices in Mississippi. Results are presented of nonlinear damage response and displacement ductility performance of the reinforced concrete bents and their foundations predicted using static finite element (FE) computations. The model considers the composite action of the concrete and the reinforcing steel materials under axial force, shear, torsion and flexure. The performance-based evaluation includes three-dimensional computational simulations of the nonlinear bridge system, including substructures and superstructure. The response spectrum dynamic analysis method will also be carried out on the linear elastic three-dimensional model to predict the linear elastic behavior. Field vibration measurements, including ambient and hammer-impact, were performed to calibrate the models. The computed transfer functions are currently being evaluated to correlate vibration measurements and the Finite element models.

Sign in / Sign up

Export Citation Format

Share Document