scholarly journals Two-Phase Flow Development of R134a in a Horizontal Pipe: Computational Investigation

2021 ◽  
Vol 39 (5) ◽  
pp. 1532-1540
Author(s):  
Raid A. Mahmood ◽  
Khalid Saleh ◽  
Veyan A. Musa ◽  
Enass Massoud ◽  
Ahmad Sharifian-Barforoush ◽  
...  
Keyword(s):  
Two Phase Flow ◽  
Three Dimensional ◽  
Phase Flow ◽  
Vapor Quality ◽  
Computational Investigation ◽  
Two Phase ◽  
Horizontal Pipe ◽  
Flow Development ◽  
Flash Tank ◽  
Region Length

To improve the performance of vapor compression refrigeration systems that use vertical gravitational flash tank separators, the liquid separation efficiency of the vertical gravitational flash tank separator requires to be approved. To approach this improvement, the two-phase flow development and its behavior after the expansion device need to be investigated and predicted. For thus, this paper presents a three-dimensional computational investigation of the two-phase flow development of R134a after the expansion device in a horizontal pipe. Computational Fluid Dynamic (CFD) was used to predict the two-phase development and its behavior in the horizontal pipe. ANSYS 16.2 program was used to generates the geometry of the three-dimensional horizontal pipe of 2 meters long and 25 mm inner diameter. The hexahedral mesh was generated and it is assessed to obtain the optimum mesh size and number. Eulerian-Eulerian two-phase model was used with k-ɛ turbulence model. R134a was used as a working fluid in the horizontal pipe utilizing four different inlet diameters: 12, 12.5, 25, and 50.0 mm. Mass flux and vapor quality have been changed from 288 to 447 kg/m2.s and from 10 to 20% respectively. Results were validated against experimental results from the literature and revealed that the separation region length is affected by the initial phase velocities, inlet vapor quality, and inlet tube diameter. An empirical correlation to predict the expansion region length is proposed as a function of Froude, Webber, and Lockhart-Martinelli numbers.

Experimental investigation on the initiation and flow development of gas-liquid slug two-phase flow in a horizontal pipe

2017 ◽  
Vol 81 ◽  
pp. 93-108 ◽  
Author(s):  
Okto Dinaryanto ◽  
Yosephus Ardean Kurnianto Prayitno ◽  
Akmal Irfan Majid ◽  
Akhmad Zidni Hudaya ◽  
Yusnanda Agus Nusirwan ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Liquid Slug ◽  
Two Phase ◽  
Horizontal Pipe ◽  
Flow Development

Pressure Drop for Oil-Gas Two-Phase Flow Through Straight Horizontal Pipe

2007 ◽  
Author(s):  
Wenhong Liu ◽  
Liejin Guo ◽  
Ximin Zhang ◽  
Kai Lin ◽  
Long Yang ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Horizontal Pipe ◽  
Flow Through ◽  
Oil Gas

scholarly journals Experimental Investigation and Prediction on Pressure Drop during Flow Boiling in Horizontal Microchannels

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 510
Author(s):  
Yan Huang ◽  
Bifen Shu ◽  
Shengnan Zhou ◽  
Qi Shi
Keyword(s):  
Pressure Drop ◽  
Flow Model ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Separated Flow ◽  
Heat Fluxes ◽  
Phase Flow ◽  
Vapor Quality ◽  
Two Phase ◽  
Gas Flux

In this paper, two-phase pressure drop data were obtained for boiling in horizontal rectangular microchannels with a hydraulic diameter of 0.55 mm for R-134a over mass velocities from 790 to 1122, heat fluxes from 0 to 31.08 kW/m2 and vapor qualities from 0 to 0.25. The experimental results show that the Chisholm parameter in the separated flow model relies heavily on the vapor quality, especially in the low vapor quality region (from 0 to 0.1), where the two-phase flow pattern is mainly bubbly and slug flow. Then, the measured pressure drop data are compared with those from six separated flow models. Based on the comparison result, the superficial gas flux is introduced in this paper to consider the comprehensive influence of mass velocity and vapor quality on two-phase flow pressure drop, and a new equation for the Chisholm parameter in the separated flow model is proposed as a function of the superficial gas flux . The mean absolute error (MAE ) of the new flow correlation is 16.82%, which is significantly lower than the other correlations. Moreover, the applicability of the new expression has been verified by the experimental data in other literatures.

A Combined Eulerian and Lagrangian Method for Prediction of Evaporating Sprays

2002 ◽  
Vol 124 (3) ◽  
pp. 481-488 ◽  
Author(s):  
M. Burger ◽  
G. Klose ◽  
G. Rottenkolber ◽  
R. Schmehl ◽  
D. Giebert ◽  
...  
Keyword(s):  
Two Phase Flow ◽  
Initial Conditions ◽  
Three Dimensional ◽  
Lagrangian Method ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Lagrangian Methods ◽  
Eulerian Method ◽  
Lagrangian Modeling

Polydisperse sprays in complex three-dimensional flow systems are important in many technical applications. Numerical descriptions of sprays are used to achieve a fast and accurate prediction of complex two-phase flows. The Eulerian and Lagrangian methods are two essentially different approaches for the modeling of disperse two-phase flows. Both methods have been implemented into the same computational fluid dynamics package which is based on a three-dimensional body-fitted finite volume method. Considering sprays represented by a small number of droplet starting conditions, the Eulerian method is clearly superior in terms of computational efficiency. However, with respect to complex polydisperse sprays, the Lagrangian technique gives a higher accuracy. In addition, Lagrangian modeling of secondary effects such as spray-wall interaction enhances the physical description of the two-phase flow. Therefore, in the present approach the Eulerian and the Lagrangian methods have been combined in a hybrid method. The Eulerian method is used to determine a preliminary solution of the two-phase flow field. Subsequently, the Lagrangian method is employed to improve the accuracy of the first solution using detailed sets of initial conditions. Consequently, this combined approach improves the overall convergence behavior of the simulation. In the final section, the advantages of each method are discussed when predicting an evaporating spray in an intake manifold of an internal combustion engine.

scholarly journals Numerical Simulation and Analysis on Spray Drift Movement of Multirotor Plant Protection Unmanned Aerial Vehicle

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2399 ◽  
Author(s):  
Fengbo Yang ◽  
Xinyu Xue ◽  
Chen Cai ◽  
Zhu Sun ◽  
Qingqing Zhou
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Droplet Size ◽  
Wind Field ◽  
Flow Model ◽  
Two Phase Flow ◽  
Plant Protection ◽  
Three Dimensional ◽  
Phase Flow ◽  
Two Phase

In recent years, multirotor unmanned aerial vehicles (UAVs) have become more and more important in the field of plant protection in China. Multirotor unmanned plant protection UAVs have been widely used in vast plains, hills, mountains, and other regions, and become an integral part of China’s agricultural mechanization and modernization. The easy takeoff and landing performances of UAVs are urgently required for timely and effective spraying, especially in dispersed plots and hilly mountains. However, the unclearness of wind field distribution leads to more serious droplet drift problems. The drift and distribution of droplets, which depend on airflow distribution characteristics of UAVs and the droplet size of the nozzle, are directly related to the control effect of pesticide and crop growth in different growth periods. This paper proposes an approach to research the influence of the downwash and windward airflow on the motion distribution of droplet group for the SLK-5 six-rotor plant protection UAV. At first, based on the Navier-Stokes (N-S) equation and SST k–ε turbulence model, the three-dimensional wind field numerical model is established for a six-rotor plant protection UAV under 3 kg load condition. Droplet discrete phase is added to N-S equation, the momentum and energy equations are also corrected for continuous phase to establish a two-phase flow model, and a three-dimensional two-phase flow model is finally established for the six-rotor plant protection UAV. By comparing with the experiment, this paper verifies the feasibility and accuracy of a computational fluid dynamics (CFD) method in the calculation of wind field and spraying two-phase flow field. Analyses are carried out through the combination of computational fluid dynamics and radial basis neural network, and this paper, finally, discusses the influence of windward airflow and droplet size on the movement of droplet groups.

Two-Phase Flow Field Numerical Simulation in Scrubber for Exhaust Gas Desulfurization

2014 ◽  
Vol 541-542 ◽  
pp. 1288-1291
Author(s):  
Zhi Feng Dong ◽  
Quan Jin Kuang ◽  
Yong Zheng Gu ◽  
Rong Yao ◽  
Hong Wei Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Flue Gas ◽  
Two Phase Flow ◽  
Three Dimensional ◽  
Flue Gas Desulfurization ◽  
Parameter Design ◽  
Phase Flow ◽  
Two Phase ◽  
Entrance Angle

Calculation fluid dynamics software Fluent was used to conduct three-dimensional numerical simulation on gas-liquid two-phase flow field in a wet flue gas desulfurization scrubber. The k-ε model and SIMPLE computing were adopted in the analysis. The numerical simulation results show that the different gas entrance angles lead to internal changes of gas-liquid two-phase flow field, which provides references for reasonable parameter design of entrance angle in the scrubber.

Sign in / Sign up

Export Citation Format

Share Document