Literature Survey on Loss Reduction Methods for Three Phase Unbalanced Radial Distribution Network

2016 ◽  
Author(s):  
Rohit Nandi, Smarajit Ghosh ◽  
Keyword(s):  
Radial Distribution ◽  
Distribution Network ◽  
Literature Survey ◽  
Loss Reduction ◽  
Three Phase ◽  
Reduction Methods

Power Flow Solution of Three-Phase Unbalanced Radial Distribution Network

2004 ◽  
Vol 32 (4) ◽  
pp. 421-433 ◽  
Author(s):  
R. RANJAN ◽  
B. VENKATESH ◽  
A. CHATURVEDI ◽  
D. DAS
Keyword(s):  
Radial Distribution ◽  
Power Flow ◽  
Distribution Network ◽  
Flow Solution ◽  
Three Phase

scholarly journals Network Reconfiguration for Loss Reduction and Voltage Profile Improvement of 110-Bus Radial Distribution System Using Exhaustive Search Techniques

2015 ◽  
Vol 5 (4) ◽  
pp. 788
Author(s):  
Su Mon Myint ◽  
Soe Win Naing
Keyword(s):  
Radial Distribution ◽  
Power Dissipation ◽  
Distribution System ◽  
Distribution Systems ◽  
Distribution Network ◽  
Network Reconfiguration ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Power Losses ◽  
Voltage Profile Improvement

Nowadays, the electricity demand is increasing day by day and hence it is very important not only to extract electrical energy from all possible new power resources but also to reduce power losses to an acceptable minimum level in the existing distribution networks where a large amount of power dissipation occurred. In Myanmar, a lot of power is remarkably dissipated in distribution system.  Among methods in reducing power losses, network reconfiguration method is employed for loss minimization and exhaustive technique is also applied to achieve the minimal loss switching scheme. Network reconfiguration in distribution systems is performed by opening sectionalizing switches and closing tie switches of the network for loss reduction and voltage profile improvement. The distribution network for existing and reconfiguration conditions are modelled and simulated by Electrical Transient Analyzer Program (ETAP) 7.5 version software. The inputs are given based on the real time data collected from 33/11kV substations under Yangon Electricity Supply Board (YESB). The proposed method is tested on 110-Bus, overhead AC radial distribution network of Dagon Seikkan Township since it is long-length, overloaded lines and high level of power dissipation is occurred in this system. According to simulation results of load flow analysis, voltage profile enhancement and power loss reduction for proposed system are revealed in this paper.

scholarly journals Loss Minimization of Power Distribution Network using Different Types of Distributed Generation Unit

2015 ◽  
Vol 5 (5) ◽  
pp. 918
Author(s):  
Su Hlaing Win ◽  
Pyone Lai Swe
Keyword(s):  
Power System ◽  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Distribution Network ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Optimum Location ◽  
Power Losses

A Radial Distribution network is important in power system area because of its simple design and reduced cost. Reduction of system losses and improvement of voltage profile is one of the key aspects in power system operation. Distributed generators are beneficial in reducing losses effectively in distribution systems as compared to other methods of loss reduction. Sizing and location of DG sources places an important role in reducing losses in distribution network. Four types of DG are considered in this paper with one DG installed for minimize the total real and reactive power losses. The objective of this methodology is to calculate size and to identify the corresponding optimum location for DG placement for minimizing the total real and reactive power losses and to improve voltage profile   in primary distribution system. It can obtain maximum loss reduction for each of four types of optimally placed DGs. Optimal sizing of Distributed Generation can be calculated using exact loss formula and an efficient approach is used to determine the optimum location for Distributed Generation Placement.  To demonstrate the performance of the proposed approach 36-bus radial distribution system in Belin Substation in Myanmar was tested and validated with different sizes and the result was discussed.

Power Flow Solution of Three-Phase Unbalanced Radial Distribution Network

2004 ◽  
Vol 32 (4) ◽  
pp. 1-1
Author(s):  
R. Ranjan ◽  
B. Venkatesh ◽  
A. Chaturvedi ◽  
D. Das
Keyword(s):  
Radial Distribution ◽  
Power Flow ◽  
Distribution Network ◽  
Flow Solution ◽  
Three Phase

scholarly journals Power-Flow Development Based on the Modified Backward-Forward for Voltage Profile Improvement of Distribution System

2016 ◽  
Vol 6 (5) ◽  
pp. 2005
Author(s):  
Suyanto Suyanto ◽  
Citra Rahmadhani ◽  
Ontoseno Penangsang ◽  
Adi Soeprijanto
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Power Flow ◽  
Distribution Network ◽  
Flow Simulation ◽  
Voltage Profile ◽  
Radial Distribution System ◽  
Flow Development ◽  
Three Phase

<p>Unbalanced three-phase radial distribution system has a complex problem in power system. It has many branches and it is sometimes voltage profile’s not stable at every end branches. For improvement of voltage profile, it can be performed by penetrating of a distributed generation models. Information of voltage profile can be gained by study of power flow.  The Modified Backward-Forward is one of the most widely used methods of development of power flow and has been extensively used for voltage profile analysis. In this paper, a study of power flow based on the Modified Backward-Forward method was used to capture the complexities of unbalanced three phase radial distribution system in the 20 kV distribution network in North Surabaya city, East Java, Indonesia within considering distributed generation models. In summary, for the informants in this study, the Modified Backward-Forward method has had quickly convergence and it’s just needed 3 to 5 iteration of power flow simulation which’s compared to other power flow development methods. Distributed Generation models in the modified the modified 34 BUS IEEE system and 20 kV distribution network has gained voltage profile value on limited range. One of the more significant findings to emerge from this development is that the Modified Backward-Forward method has average of error voltage about 0.0017 % to 0.1749%.</p>

Sign in / Sign up

Export Citation Format

Share Document