scholarly journals Time Study on The Activity of Oil Palm Harvesting at Sari Lembah Subur Plantations, Riau

2012 ◽  
Vol 26 (2) ◽  
pp. 99-106
Author(s):  
Kurnia Ayu Putranti ◽  
◽  
Sam Herodian ◽  
M. Faiz Syuaib
Keyword(s):  
Oil Palm ◽  
2015 ◽  
Vol 74 (3) ◽  
Author(s):  
Nizaroyani Saibani ◽  
Ariff Azly Muhamed ◽  
Mohd Faizal Maliami ◽  
Rasyidah Ahmad

In optimizing the yield of oil palm fruit bunches collection, the mechanization of the collection process is very important. However, before the analysis of the cost benefits of any mechanization development can be utilized, this study has to be carried out. Time and Motion Studies (TMS) is used to identify and measure the efficiency of the oil palm fruit bunches’ manual harvesting technique. The Direct Time Study Technique has been selected to determine and record the time taken by the harvester to harvest the oil palm fruit bunches, where the tool used in this technique is a stopwatch, alongside the Time Study Observation Sheet. Meanwhile, to examine the motions used by the harvester in the harvesting process, the Therblig’s Motion Principle is applied to identify effective and non- effective motions. A field work study has been conducted by monitoring two harvesters and all the real time data is recorded in the time study observation sheet and analyzed to get a value of Normal Time (NT) and also Standard Time (ST) for each work element involved in the manual harvesting process of palm oil. There are seven work elements that have been identified to have been used by the harvester to complete the process, the first element  is searching for the mature palm oil tree (NT= 40.73 seconds), the second element  is adjusting the Aluminium Pole and Knife (APK) cutter (NT= 23.36 seconds), the third element is cutting the oil palm’s frond (NT= 51.30 seconds), the fourth element is cutting  the mature oil palm’s bunches (NT= 60.26 seconds), the fifth element is collecting the oil palm’s frond that  has been cut (NT= 21.69 seconds), the sixth element is putting the oil palm’s bunches that have been cut  into the wheel barrow (NT= 34.25 seconds) and the seventh element  is collecting the loose oil palm fruits or called fruitlets (NT= 77.49 seconds). The study also categorized a few non-effective work elements carried out during the manual harvesting process. The elements are: searching for the oil palm trees that have mature oil palm bunches, adjusting the APK cutter and also collecting the loose oil palm fruitlets off the ground.


1932 ◽  
Vol 11 (9) ◽  
pp. 412
Author(s):  
R.W. Bedford ◽  
Roland ◽  
Bedford ◽  
Horridge ◽  
Wright ◽  
...  
Keyword(s):  

2007 ◽  
Vol 34 (S 2) ◽  
Author(s):  
TD Hälbig ◽  
S Assuras ◽  
J Barry ◽  
JC Borod ◽  
JM Gracies ◽  
...  

2015 ◽  
Vol 2 (2) ◽  
pp. 148-158
Author(s):  
Surianto

Spodosol soil of Typic Placorthod sub-group of East Barito District is one of the problem soils with the presence of hardpan layer, low fertility, low water holding capacity, acid reaction and it is not suitable for oil palm cultivation without any properly specific management of land preparation and implemented best agronomic practices. A study was carried out to evaluate the soil characteristic of a big hole (A profile) and no big hole (B profile) system and comparative oil palm productivity among two planting systems. This study was conducted in Spodosol soil at oil palm plantation (coordinate X = 0281843 and Y = 9764116), East Barito District, Central Kalimantan Province on February 2014, by surveying of placic and ortstein depth and observing soil texture and chemical properties of 2 (two) oil palm's soil profiles that have been planted in five years. Big hole system of commercial oil palm field planting on the Spodosol soil area was designed for the specific purpose of minimizing the potential of a negative effect of shallow effective planting depth for oil palms growing due to the hardpan layer (placic and ortstein) presence as deep as 0.25 - 0.50 m. The big hole system is a planting hole type which was vertical-sided with 2.00 m x 1.50 m on top and bottom side and 3.00 m depth meanwhile the 2:1 drain was vertical-sided also with 1.50 m depth and 300 m length. Oil palm production was recorded from the year 2012 up to 2014. Results indicated that the fractions both big hole profile (A profile) and no big hole profile (B profile) were dominated by sands ranged from 60% to 92% and the highest sands content of non-big hole soil profile were found in A and E horizons (92%). Better distribution of sand and clay fractions content in between layers of big hole soil profiles of A profile sample is more uniform compared to the B profile sample. The mechanical holing and material mixing of soil materials of A soil profile among the upper and lower horizons i.e. A, E, B and C horizons before planting that resulted a better distribution of both soil texture (sands and clay) and chemical properties such as acidity value (pH), C-organic, N, C/N ratio, CEC, P-available and Exchangeable Bases. Investigation showed that exchangeable cations (Ca, Mg, K), were very low in soil layers (A profile) and horizons (B profile) investigated. The low exchangeable cations due to highly leached of bases to the lower layers and horizons. Besides, the palm which was planted on the big hole system showed good adaptation and response positively by growing well of tertiary and quaternary roots that the roots were penetrable into deeper rooting zone as much as >1.00 m depth. The roots can grow well and penetrate much deeper in A profile compared to the undisturbed hardpan layer (B profile). The FFB (fresh fruit bunches) production of the non-big hole block was higher than the big hole block for the first three years of production. This might be due to the high variation of monthly rainfall in-between years of observation from 2009 to 2014. Therefore, the hardness of placic and ortstein as unpenetrable agents by roots and water to prevent water loss and retain the water in the rhizosphere especially in the drier weather. In the high rainfall condition, the 2:1 drain to prevent water saturation in the oil palm rhizosphere by moving some water into the drain. Meanwhile, the disturbed soil horizon (big hole area) was drier than un disturbance immediately due to water removal to deeper layers. We concluded that both big hole and 2:1 drain are a suitable technology for Spodosol soil land especially in preparing palms planting to minimize the negative effect of the hardpan layer for oil palm growth.


2013 ◽  
Author(s):  
Artchapong Hassametto ◽  
Preerawadee Chaiboontun ◽  
Chattraporn Prajuabwan ◽  
Laphatrada Khammuang ◽  
Aussadavut Dumrongsiri

SIMBIOSA ◽  
2014 ◽  
Vol 3 (1) ◽  
Author(s):  
Fauziah Syamsi

Kelapa sawit merupakan salah satu tanaman meningkat paling pesat di dunia, dan mencakup lebih dari 13 juta ha di Asia Tenggara. Sumatera memiliki sejarah yang relatif panjang budidaya kelapa sawit komersial, dan banyak perkebunan telah menggantikan hutan hujan. Biasanya ini perkebunan monokultur mendukung spesies lebih sedikit daripada hutan, namun ada sangat sedikit informasi yang tersedia untuk kelelawar. Kami mencicipi kelelawar pemakan serangga di Sumatera Barat dalam perkebunan kelapa sawit matang di mana beberapa tutupan hutan dipertahankan di fragmen hutan di bukit-bukit dan di sepanjang sungai. Menggunakan total 180 kecapi perangkap malam kami dibandingkan dengan komunitas kelelawar dalam tiga jenis habitat: patch hutan, zona riparian dan perkebunan. Total kami ditangkap 1108 kelelawar yang mewakili 21 spesies dan 5 keluarga, dan mayoritas ini (dalam hal spesies dan kelimpahan) ditemukan di fragmen hutan. perkebunan kelapa sawit ditemukan menjadi habitat miskin untuk kelelawar - hanya empat orang dari dua spesies ditangkap. daerah pinggiran sungai didukung keanekaragaman menengah, dan mungkin penting sebagai koridor satwa liar antara fragmen hutan. Kata kunci : Biodiversitas, keleawar Microchiropteran


Sign in / Sign up

Export Citation Format

Share Document