Characteristics of Cutting Marks that Appear on Electric Wires According to the Operating Structure and Principle of Cutting Tools

2021 ◽  
Vol 15 (4) ◽  
pp. 255-263
Author(s):  
Soo-Kyung Kim ◽  
Young-Wook Yoon
Keyword(s):  
Cutting Tools

The application of tungsten carbide cutting tools

1949 ◽  
Vol 28 (7) ◽  
pp. 394
Author(s):  
C. Eatough ◽  
H. Eckersley
Keyword(s):  
Tungsten Carbide ◽  
Cutting Tools

Laser stripping of CrTiAlN coating to facilitate re-use of cutting tools

2008 ◽  
Author(s):  
M. Sundar ◽  
D. Whitehead ◽  
P. Mativenga ◽  
L. Li ◽  
Y. Shicai ◽  
...  
Keyword(s):  
Cutting Tools

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

Optimization of cryogenic treatment effects on the surface roughness of cutting tools

2019 ◽  
Vol 61 (11) ◽  
pp. 1101-1104 ◽  
Author(s):  
Fuat Kara ◽  
Aysun Takmaz
Keyword(s):  
Surface Roughness ◽  
Treatment Effects ◽  
Cryogenic Treatment ◽  
Cutting Tools

Performance of coated and uncoated carbide/cermet cutting tools during turning

2018 ◽  
Vol 60 (9) ◽  
pp. 893-901 ◽  
Author(s):  
Hasan Basri Ulas ◽  
Musa Bilgin ◽  
Huseyin Kursad Sezer ◽  
Murat Tolga Ozkan
Keyword(s):  
Cutting Tools

TANTUNG G

Alloy Digest ◽  
1961 ◽  
Vol 10 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Cutting Tools ◽  
Heat Treating ◽  
Nonferrous Alloy ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

Abstract TANTUNG G is a cast nonferrous alloy containing tantalum or columbium carbide and having wear and corrosion resistance. It is used primarily for cutting tools. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: Co-28. Producer or source: Vascoloy, Ramet Division.

RED STAR TUNGSTEN

Alloy Digest ◽  
1965 ◽  
Vol 14 (12) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Cutting Tools ◽  
High Hardness ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
Vanadium Alloys ◽  
Alloy Tool ◽  
Thread Rolling

Abstract Red Star Tungsten is a high-carbon low-alloy tool steel having high hardness, good toughness, and keen cutting edge. It is recommended for cutting tools, thread rolling dies, paper knives, etc. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as deformation. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-173. Producer or source: Vanadium Alloys Steel Company.

UNS T11310

Alloy Digest ◽  
1988 ◽  
Vol 37 (5) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Tool Steel ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Heat Treating ◽  
General Purpose ◽  
Steel Mills

Abstract UNS No. T11310 is the high vanadium type of molybdenum high-speed steel. It is a deep-hardening steel and offers high cutting ability and excellent finishing properties. It is a general-purpose steel for cutting tools and is used in such applications as taps, lathe tools and reamers. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on heat treating and machining. Filing Code: TS-490. Producer or source: Tool steel mills.

Sign in / Sign up

Export Citation Format

Share Document