scholarly journals Effects on the Thermal Shock Resistance of Ceramic Coating of Nickel-flash and Mill Addition of Cobalt Oxide Fired in Nitrogen Stream

1957 ◽  
Vol 65 (735) ◽  
pp. 41-50
Author(s):  
Chihiro KAWASHIMA ◽  
Yorihiro MURATA
Keyword(s):  
Thermal Shock ◽  
Cobalt Oxide ◽  
Thermal Shock Resistance ◽  
Ceramic Coating ◽  
Nitrogen Stream ◽  
Shock Resistance ◽  
Mill Addition

Fabrication of Self-Healing Ceramic Coating Against Oxidation for Carbon/Carbon Composite Using Polysilazane and Fillers

2009 ◽  
Vol 79-82 ◽  
pp. 775-778 ◽  
Author(s):  
Hong Li Liu ◽  
Chun Ying Tian
Keyword(s):  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Loss Rate ◽  
Ceramic Coating ◽  
Carbon Composite ◽  
Self Healing ◽  
Weight Loss Rate ◽  
Shock Resistance ◽  
Polymer Pyrolysis ◽  
Sealing Layer

The self-healing ceramic coating against oxidation for carbon/carbon composite was fabricated via preceramic polymer pyrolysis process using polysilazane as preceramic and MoSi2, B4C powders as fillers. By means of SEM and XRD, the phase compose and microstructure of coating were characterized, and preliminarily study on its anti-oxidation ability and thermal shock resistance were conducted. The results showed that, the coating is composed of the resisting oxidation layer and the sealing layer. The thickness of the coating is about 50μm, and the coating is uniform and densified. Good contact at the interfaces is visible on the SEM photograph. At 1300°C temperature, the thermal shock resistance test was conducted 50 times, the weight loss rate was 2.12%. In range of 1200°C~1500°C, the anti oxidation ability of the coating is good.

A protective ceramic coating to improve oxidation and thermal shock resistance on CrMn alloy at elevated temperatures

2015 ◽  
Vol 41 (3) ◽  
pp. 4706-4713 ◽  
Author(s):  
X. Shan ◽  
L.Q. Wei ◽  
X.M. Zhang ◽  
W.H. Li ◽  
W.X. Tang ◽  
...  
Keyword(s):  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Ceramic Coating ◽  
Elevated Temperatures ◽  
Shock Resistance

A new high thermal shock resistant onelayer glass–ceramic coating for industrial and engineering applications

2017 ◽  
Vol 2 (82) ◽  
pp. 70-76
Author(s):  
J.H. Mohmmed
Keyword(s):  
Thermal Conductivity ◽  
Thermal Expansion ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Ceramic Coating ◽  
Lithium Oxide ◽  
Coating System ◽  
Glass Ceramic Coating ◽  
Resultant Coating ◽  
Shock Resistance

Purpose: A new high thermal stability single layer glass–ceramic coating system designing for applied on various grade of steel alloy has been developed in this work. Design/methodology/approach: The thermal shock resistance, thermal conductivity and thermal expansion of the coating system were evaluated by using suitable standard tests. Some crystalline agents (Lithium oxide Li2O, Titanium oxide TiO2, Zircon ZrSiO4 and Feldspar CaO∙Al2O3∙2SiO2) were add at constant ratio 6% to coating system to evaluate their effects on the resultant coatings. Findings: The results indicate the suitability of these coatings for protection of metal substrate. Also the results show that the properties of resultant coating were hardly affected by composition and concentration of crystalline agent. Research limitations/implications: Coating with lithium oxide has the lowest thermal expansion, which means the highest thermal shock resistance. While, values of thermal conductivity were too close for all types of coating. Originality/value: Generally, the resultant coating properties have been enhanced in all cases; this is associated with the introduce the crystalline agent which lead to the formation of a complex network of crystalline phases.

Effect of Heat Treatment Temperature on Properties of SiO2-ZrO2-Al2O3-Cr2O3 Coatings on Stainless Steel Substrate

2012 ◽  
Vol 538-541 ◽  
pp. 359-362
Author(s):  
Qing Mei Jia ◽  
Yong Hong Tang ◽  
Ke Nan Meng
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Thermal Shock ◽  
Abrasion Resistance ◽  
Thermal Shock Resistance ◽  
Ceramic Coating ◽  
Erosion Resistance ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Shock Resistance

The SiO2-ZrO2-Al2O3-Cr2O3 film is coated on the surface of stainless steel using analytical reagent TEOS, ZrOCl2·8H2O, Al(NO3)3·9H2O and Cr(NO3)3·9H2O as precursor and basing on mole ratio to calculate through Sol-gel method. The phase transformation behavior，erosion resistance，thermal shock resistance and abrasion resistance of ceramic coating by different heat treatment are studied. The results show that: 1)The SiO2-ZrO2-Al2O3-Cr2O3 gel coatings has non-crystalline structure after the treatment at 700°C and 800°C. New substance is not created below 700°C 2) The stainless steel substrate with ceramic coating has a higher erosion resistance at high temperature (700°Cand 800°C)than that without coating.3) Thermal shock resistance of the samples treated in 700°C is the best which has reached within 17-21cycles (900°C, air cooling). 4) The stainless steel substrate with ceramic coating has a higher abrasion resistance than that without coating. The samples treated at 700°Cand 800°C have the best abrasion resistance.

The Effect of Mill Addition of Quartz Glass on Thermal Shock Resistance of Sheet Steel Enamels

2017 ◽  
Vol 898 ◽  
pp. 1583-1588
Author(s):  
Li Yun Chen ◽  
Yan Yan Wu ◽  
Wei Zhong Jiang ◽  
Jia Yi Ye ◽  
Hui Le Jin ◽  
...  
Keyword(s):  
Thermal Shock ◽  
Quartz Glass ◽  
Thermal Shock Resistance ◽  
Sheet Steel ◽  
Acid Resistance ◽  
Manufacturing Technology ◽  
Shock Resistance ◽  
Mill Addition ◽  
Rational Range

Sheet steel enamels with mill addition of quartz glass were manufactured successfully in accordance with the ordinary enamel manufacturing technology. The effect of mill addition of quartz glass on thermal shock resistance and acid resistance of enamels was analyzed through XRD and SEM etc. The results show that the thermal shock of the enamel can be increased greatly by mill addition of quartz glass, and there is the rational range of mill addition of quartz glass in order for the enamel to achieve both the superior acid resistance and the excellent thermal shock.

Effect of Heat Treatment Temperature on Properties of SiO2-ZrO2-Al2O3-Cr2O3 Coatings on Stainless Steel Substrate

2010 ◽  
Vol 177 ◽  
pp. 321-324
Author(s):  
Shu Xian Liu ◽  
Qian Ping Wang ◽  
Yi Miao Nie
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Thermal Shock ◽  
Abrasion Resistance ◽  
Thermal Shock Resistance ◽  
Ceramic Coating ◽  
Erosion Resistance ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Shock Resistance

The SiO2-ZrO2-Al2O3-Cr2O3 film is coated on the surface of stainless steel using analytical reagent TEOS, ZrOCl2•8H2O, Al(NO3)3•9H2O and Cr(NO3)3•9H2O as precursor and basing on mole ratio to calculate through Sol-gel method. The phase transformation behavior, erosion resistance, thermal shock resistance and abrasion resistance of ceramic coating by different heat treatment are studied. The results show that: 1) The SiO2-ZrO2-Al2O3-Cr2O3 gel coatings has non-crystalline structure after the treatment at 700°C and 800°C. New substance is not created below 700°C. 2) The stainless steel substrate with ceramic coating has a higher erosion resistance at high temperature (700°C and 800°C)than that without coating.3) Thermal shock resistance of the samples treated in 700°C is the best which has reached within 17-21cycles (900°C, air cooling). 4) The stainless steel substrate with ceramic coating has a higher abrasion resistance than that without coating. The samples treated at 700°C and 800°C have the best abrasion resistance.

Sign in / Sign up

Export Citation Format

Share Document