scholarly journals Optical scanner for steam generator tube inspection. Final report. [PWR]

1980 ◽  
Author(s):  
R. Ginaven ◽  
R. Smith, II ◽  
V. Orphan ◽  
G. Hall ◽  
E. Meckstroth
Keyword(s):  
Steam Generator ◽  
Final Report ◽  
Steam Generator Tube ◽  
Optical Scanner

scholarly journals Evaluation of steam generator tube 85-127 from Oconee 1B. Final report

1981 ◽  
Author(s):  
M. Rigdon ◽  
L. Sarver
Keyword(s):  
Steam Generator ◽  
Final Report ◽  
Steam Generator Tube

scholarly journals Steam generator tube integrity program: Phase II, Final report

1988 ◽  
Author(s):  
R.J. Kurtz ◽  
R.L. Bickford ◽  
R.A. Clark ◽  
C.J. Morris ◽  
F.A. Simonen ◽  
...  
Keyword(s):  
Steam Generator ◽  
Phase Ii ◽  
Final Report ◽  
Steam Generator Tube

scholarly journals Analysis of the Accelerator-Driven System Fuel Assembly during the Steam Generator Tube Rupture Accident

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1818
Author(s):  
Di-Si Wang ◽  
Bo Liu ◽  
Sheng Yang ◽  
Bin Xi ◽  
Long Gu ◽  
...  
Keyword(s):  
Fuel Assembly ◽  
Steam Generator ◽  
Metal Flow ◽  
Maximum Temperature ◽  
Steam Generator Tube ◽  
Driven System ◽  
Fuel Assemblies ◽  
Accelerator Driven System ◽  
The Impact ◽  
Steam Bubble

China is developing an ADS (Accelerator-Driven System) research device named the China initiative accelerator-driven system (CiADS). When performing a safety analysis of this new proposed design, the core behavior during the steam generator tube rupture (SGTR) accident has to be investigated. The purpose of our research in this paper is to investigate the impact from different heating conditions and inlet steam contents on steam bubble and coolant temperature distributions in ADS fuel assemblies during a postulated SGTR accident by performing necessary computational fluid dynamics (CFD) simulations. In this research, the open source CFD calculation software OpenFOAM, together with the two-phase VOF (Volume of Fluid) model were used to simulate the steam bubble behavior in heavy liquid metal flow. The model was validated with experimental results published in the open literature. Based on our simulation results, it can be noticed that steam bubbles will accumulate at the periphery region of fuel assemblies, and the maximum temperature in fuel assembly will not overwhelm its working limit during the postulated SGTR accident when the steam content at assembly inlet is less than 15%.

Time Domain Simulation of the Vibration of a Steam Generator Tube Subjected to Fluidelastic Forces Induced by Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Téguewindé Sawadogo ◽  
Njuki Mureithi
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Work Rate ◽  
Fretting Wear ◽  
Phase Flow ◽  
Reference Case ◽  
Two Phase ◽  
Steam Generator Tube ◽  
Wide Range ◽  
Instability Regime

Having previously verified the quasi-steady model under two-phase flow laboratory conditions, the present work investigates the feasibility of practical application of the model to a prototypical steam generator (SG) tube subjected to a nonuniform two-phase flow. The SG tube vibration response and normal work-rate induced by tube-support interaction are computed for a range of flow conditions. Similar computations are performed using the Connors model as a reference case. In the quasi-steady model, the fluid forces are expressed in terms of the quasi-static drag and lift force coefficients and their derivatives. These forces have been measured in two-phase flow over a wide range of void fractions making it possible to model the effect of void fraction variation along the tube span. A full steam generator tube subjected to a nonuniform two-phase flow was considered in the simulations. The nonuniform flow distribution corresponds to that along a prototypical steam-generator tube based on thermal-hydraulic computations. Computation results show significant and important differences between the Connors model and the two-phase flow based quasi-steady model. While both models predict the occurrence of fluidelastic instability, the predicted pre-instability and post instability behavior is very different in the two models. The Connors model underestimates the flow-induced negative damping in the pre-instability regime and vastly overestimates it in the post instability velocity range. As a result the Connors model is found to underestimate the work-rate used in the fretting wear assessment at normal operating velocities, rendering the model potentially nonconservative under these practically important conditions. Above the critical velocity, this model largely overestimates the work-rate. The quasi-steady model on the other hand predicts a more moderately increasing work-rate with the flow velocity. The work-rates predicted by the model are found to be within the range of experimental results, giving further confidence to the predictive ability of the model. Finally, the two-phase flow based quasi-steady model shows that fluidelastic forces may reduce the effective tube damping in the pre-instability regime, leading to higher than expected work-rates at prototypical operating velocities.

Analysis of phase composition of corrosion-products deposits on the surfaces of a PG-440 steam-generator tube bundle by Mossbauer spectroscopy method

2009 ◽  
Vol 56 (2) ◽  
pp. 162-163
Author(s):  
A. A. Efimov ◽  
V. G. Semenov ◽  
B. A. Gusev ◽  
M. M. Kostin ◽  
I. V. Miroshnichenko ◽  
...  
Keyword(s):  
Mössbauer Spectroscopy ◽  
Phase Composition ◽  
Steam Generator ◽  
Mossbauer Spectroscopy ◽  
Tube Bundle ◽  
Corrosion Products ◽  
Spectroscopy Method ◽  
Steam Generator Tube ◽  
Mößbauer Spectroscopy
Sign in / Sign up

Export Citation Format

Share Document