scholarly journals Effects of test temperature, strain rate, and thermal exposure on the tensile properties of Alloy 600

1976 ◽  
Author(s):  
J M Steichen ◽  
A L Ward
Keyword(s):  
Strain Rate ◽  
Tensile Properties ◽  
Test Temperature ◽  
Thermal Exposure ◽  
Alloy 600 ◽  
Temperature Strain

Tensile Properties of Thermally Exposed Type 304 Stainless Steel

1976 ◽  
Vol 98 (4) ◽  
pp. 357-360 ◽  
Author(s):  
J. M. Steichen
Keyword(s):  
Stainless Steel ◽  
Strain Rate ◽  
Tensile Properties ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Thermal Exposure ◽  
304 Stainless Steel ◽  
Elevated Temperature Strength ◽  
Type 304 ◽  
Type 304 Stainless Steel

The influence of thermal exposure at 800, 1000, and 1200°F (427, 538 and 649°C) on the tensile properties of type 304 stainless steel has been experimentally determined. Specimens were exposed in static sodium for durations of 1000, 3500 and 10,000 hr. Tests were performed at room temperature and the respective exposure temperatures at nominal strain rates from 3 × 10−5 to 10 s−1. Exposure at temperatures to 1000°F (538°C) did not greatly alter the elevated temperature strength, ductility, or strain rate sensitivity of the subject material. At 1200°F (649°C) strength properties were unchanged by exposure at this temperature while ductility was increased at the lowest strain rate and slightly reduced at the higher rates. The room temperature strength was unchanged and ductility slightly reduced after exposure for 10,000 hr at each temperature.

Intergranular Stress Corrosion Cracking Damage Model: An Approach and Its Development for Alloy 600 in High-Purity Water

CORROSION ◽  
1986 ◽  
Vol 42 (2) ◽  
pp. 99-105 ◽  
Author(s):  
Y. S. Garud ◽  
A. R. McIlree
Keyword(s):  
Strain Rate ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Purity ◽  
Corrosion Cracking ◽  
Model Parameters ◽  
Alloy 600 ◽  
Intergranular Stress Corrosion ◽  
Film Rupture ◽  
Intergranular Stress Corrosion Cracking

Abstract A logical approach to quantitative modeling of intergranular stress corrosion cracking (IGSCC) is presented. The approach is based on the supposition (supported partly by experimental and field observations, and by a related plausible underlying mechanism) that strain rate is a key variable. The approach is illustrated for the specific case of NiCrFe Alloy 600 in high-purity water. Model parameters are determined based on the constant stress IGSCC data (between 290 and 365 C) assuming a power law relation between the damage and the nominal strain rate. The model may be interpreted in terms of a film rupture mechanism of the corrosion process. The related mechanistic considerations are examined for the specific case. Resulting calculations and stress as well as temperature dependence are shown to be in good agreement with the data. More data are needed for further verification under specific conditions of interest.

High Temperature Deformation Mechanism Maps of NiAl

2004 ◽  
Vol 449-452 ◽  
pp. 57-60
Author(s):  
I.G. Lee ◽  
A.K. Ghosh
Keyword(s):  
High Temperature ◽  
Strain Rate ◽  
Deformation Mechanism ◽  
Calculation Method ◽  
Deformation Behavior ◽  
Tensile Tests ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Grain Sizes ◽  
Temperature Strain

In order to analyze high temperature deformation behavior of NiAl alloys, deformation maps were constructed for stoichiometric NiAl materials with grain sizes of 4 and 200 µm. Relevant constitute equations and calculation method will be described in this paper. These maps are particularly useful in identifying the location of testing domains, such as creep and tensile tests, in relation to the stress-temperature-strain rate domains experienced by NiAl.

Sign in / Sign up

Export Citation Format

Share Document