scholarly journals Global Stability Analysis of Asymmetric Flow around a Two-Dimensional Cylinder, a Sphere, and a Three-Dimensional Low Aspect Ratio Cylinder

2003 ◽  
Vol 51 (597) ◽  
pp. 529-536 ◽  
Author(s):  
Asei Tezuka ◽  
Kojiro Suzuki
2014 ◽  
Vol 58 (01) ◽  
pp. 1-19
Author(s):  
Michael J. Hughes ◽  
Young T. Shen

The behavior of the force on a rudder changes significantly after the inception of stall, requiring different mathematical formulae to compute rudder forces prior-and poststall. Determining the inception angle at which stall occurs is important for predicting the rudder force on a maneuvering ship. A method to compute the inception angle of stall on a rudder is presented in this article. The theoretical formulation is based on a flow similarity approach, which relates three-dimensional rudder stall inception with two-dimensional airfoil data. Rudders are low-aspect ratio wings, and the three-dimensional lift is based on the low-aspect ratio wing theory. The two-dimensional airfoil stall data are obtained from National Advisory Committee for Aeronautics (NACA) reports. The derived theory is first validated with wind tunnel data from foils with a NACA 0015 profile of aspect ratios 1, 2, and 3. The theory is also validated with data from foils with a NACA 0012 profile and an aspect ratio of 2, 3, and 6.


2017 ◽  
Vol 819 ◽  
pp. 147-164 ◽  
Author(s):  
L. Siconolfi ◽  
V. Citro ◽  
F. Giannetti ◽  
S. Camarri ◽  
P. Luchini

A methodology is proposed here to estimate the stability characteristics of bluff-body wakes using local analysis under the assumption of weakly non-parallel flows. In this connection, a generalisation of the classic spatio-temporal stability analysis for fully three-dimensional flows is first described. Secondly, an additional higher-order correction term with respect to the common saddle-point global frequency estimation is included in the analysis. The proposed method is first validated for the case of the flow past a circular cylinder and then applied to two fully three-dimensional flows: the boundary layer flow over a wall-mounted hemispherical body and the wake flow past a fixed sphere. In all the cases considered, both the estimated unstable eigenvalue and the spatial shape of the associated eigenmode are determined by local stability analysis, and they are compared with the reference counterparts obtained at a definitely higher computational cost by a fully three-dimensional global stability analysis. It is shown that the results of local stability analysis, when the higher-order correction term is included, are in excellent agreement with those obtained by global stability analysis. It is also shown that the retained correction term is of crucial importance in this perspective, leading to a remarkable improvement in accuracy with respect to the classical saddle-point estimation.


2019 ◽  
Vol 863 ◽  
pp. 817-849 ◽  
Author(s):  
Kuchimanchi K. Bharadwaj ◽  
Debopam Das

The present study investigates the puffing behaviour of planar buoyant plumes by employing linear BiGlobal stability analysis and experiments. The BiGlobal instability characteristics of two-dimensional plumes have been explored using stability analysis and compared with the puffing behaviour of both rectangular plumes and square plumes obtained from experiments. In the parameter space investigated, which spans a Richardson number range $0.03<Ri<960$, instability analysis reveals that planar plumes exhibit BiGlobal instability only for varicose perturbations, while they remain stable for sinuous perturbations. The BiGlobal frequency and growth rates of the unstable varicose mode are used to obtain Strouhal number correlation and stability curves. An investigation into the effect of the spanwise wavenumber on BiGlobal instability indicates that planar plumes are more unstable to two-dimensional perturbations than to three-dimensional perturbations. An increase in the spanwise wavenumber tends to stabilize planar plumes without affecting their oscillation frequencies. Experiments suggest that the puffing frequencies in rectangular plumes closely follow the power law obtained from two-dimensional instability analysis while exhibiting a weaker dependence on inlet aspect ratio. To further explore the effect of aspect ratio on puffing behaviour, experiments have been carried out in plumes of aspect ratio 1, i.e. square plumes. Square plumes are found to be more stable and to exhibit higher puffing frequencies than rectangular plumes. The reasons for these differences in puffing dynamics between rectangular and square plumes have been explored from the phase-locked streamwise and spanwise flow visualizations. In addition to puffing, spanwise visualizations in both rectangular and square plumes show the presence of secondary flows at their corners, similar to their constant-density jet counterparts. Finally, from experiments, we deduced a new universal puffing frequency correlation with the hydraulic diameter as the length scale which eliminates the aspect ratio dependence, and is valid for both square and low-aspect-ratio rectangular plumes.


2017 ◽  
Vol 828 ◽  
pp. 57-69
Author(s):  
Xuefei Guo ◽  
Yongkang Le ◽  
Bochao Cao

The aspect ratio dependence of the electroconvection phenomenon in a suspended nematic liquid crystal film with a rectangular boundary is investigated. Two-dimensional global stability analysis is carried out on the coupled electrohydrodynamic system to calculate the instability boundary of the phenomenon for different aspect ratios. The calculated critical $R$ number (Rayleigh-like number) shows a rapidly decreasing trend in the low-aspect-ratio region (roughly $\unicode[STIX]{x1D6FE}<1.5$, where $\unicode[STIX]{x1D6FE}$ is defined as the aspect ratio of the film), and then the variation becomes slow until $\unicode[STIX]{x1D6FE}\approx 2.5$, where the critical $R$ number starts to increase slightly. Convective patterns of liquid films with different aspect ratios are also obtained from stability analysis and validated by particle image velocimetry measurement.


2007 ◽  
Vol 16 (01) ◽  
pp. 59-73 ◽  
Author(s):  
KWANG-SUP LEE ◽  
RAN HEE KIM ◽  
PREM PRABHAKARAN ◽  
DONG-YOL YANG ◽  
TAE WOO LIM ◽  
...  

Two-photon stereolithography based on photopolymerization provides the ability to fabricate real three-dimensional (3D) microstructures beyond the resolution of focal size. In this paper, our recent research focusing on improvement of spatial resolution in two-photon stereolithography is reviewed. The influence of system and fabrication conditions in relation to the spatial resolution is discussed. For small and low aspect ratio voxels, a minimum power and minimum exposure time (MPMT) scheme is introduced. During the two-photon process, an ascending technique, wherein the truncation amount of volumetric pixels is controlled, can be applied to improve the resolution of two-dimensional patterns. 3D Microfabrication with less than 100 nm resolution can be realized by using the radical quenching effect. After the two-photon process, the resolution of fabricated patterns can be refined to 60 nm by post-processing of plasma ashing.


Sign in / Sign up

Export Citation Format

Share Document