scholarly journals The Optimization of Reactive Power for Distribution Network With PV Generation Based on NSGA-III

2021 ◽  
Vol 6 (3) ◽  
pp. 193-200
Author(s):  
Yongle Ai ◽  
Keyword(s):  
Reactive Power ◽  
Distribution Network ◽  
Pv Generation

scholarly journals Distribution system power quality compensation using a HSeAPF based on SRF and SMC features

2021 ◽  
Author(s):  
Akram Qashou ◽  
Sufian Yousef ◽  
Abdallah A. Smadi ◽  
Amani A. AlOmari
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Sliding Mode ◽  
Distribution Network ◽  
Harmonic Distortion ◽  
Phase Locked Loop ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Non Linear

AbstractThe purpose of this paper is to describe the design of a Hybrid Series Active Power Filter (HSeAPF) system to improve the quality of power on three-phase power distribution grids. The system controls are comprise of Pulse Width Modulation (PWM) based on the Synchronous Reference Frame (SRF) theory, and supported by Phase Locked Loop (PLL) for generating the switching pulses to control a Voltage Source Converter (VSC). The DC link voltage is controlled by Non-Linear Sliding Mode Control (SMC) for faster response and to ensure that it is maintained at a constant value. When this voltage is compared with Proportional Integral (PI), then the improvements made can be shown. The function of HSeAPF control is to eliminate voltage fluctuations, voltage swell/sag, and prevent voltage/current harmonics are produced by both non-linear loads and small inverters connected to the distribution network. A digital Phase Locked Loop that generates frequencies and an oscillating phase-locked output signal controls the voltage. The results from the simulation indicate that the HSeAPF can effectively suppress the dynamic and harmonic reactive power compensation system. Also, the distribution network has a low Total Harmonic Distortion (< 5%), demonstrating that the designed system is efficient, which is an essential requirement when it comes to the IEEE-519 and IEC 61,000–3-6 standards.

scholarly journals Reactive power optimization system of distribution network based on edge calculation

2021 ◽  
Vol 1914 (1) ◽  
pp. 012033
Author(s):  
Jinbo Huang ◽  
Jiangxiao Fang ◽  
Liexiang Hu ◽  
Bolong Shi ◽  
Suirong Li ◽  
...  
Keyword(s):  
Reactive Power ◽  
Power Optimization ◽  
Distribution Network ◽  
Reactive Power Optimization ◽  
Optimization System

scholarly journals Solar photovoltaic-based microgrid hosting capacity evaluation in electrical energy distribution network with voltage quality analysis

2021 ◽  
Vol 3 (5) ◽  
Author(s):  
Arvind Sharma ◽  
Mohan Kolhe ◽  
Alkistis Kontou ◽  
Dimitrios Lagos ◽  
Panos Kotsampopoulos
Keyword(s):  
Reactive Power ◽  
Distribution Network ◽  
Electrical Energy ◽  
Droop Control ◽  
Solar Photovoltaic ◽  
Voltage Profile ◽  
Power Conditioning ◽  
Network Operation ◽  
Hardware In Loop ◽  
Pv Penetration

Abstract In this paper, solar photovoltaic hosting capacity within the electrical distribution network is estimated for different buses, and the impacts of high PV penetration are evaluated using power hardware-in-loop testing methods. It is observed that the considered operational constraints (i.e. voltage and loadings) and their operational limits have a significant impact on the hosting capacity results. However, with increasing photovoltaic penetration, some of the network buses reach maximum hosting capacity, which affects the network operation (e.g. bus voltages, line loading). The results show that even distributing the maximum hosting capacity among different buses can increase the bus voltage rise to 9%. To maintain the network bus voltages within acceptable limits, reactive power voltage-based droop control is implemented in the photovoltaic conditioning devices to test the dynamics of the network operation. The results show that implementation of the droop control technique can reduce the maximum voltage rise from 9% to 4% in the considered case. This paper also presents the impact of forming a mesh type network (i.e. from radial network) on the voltage profile during PV penetration, and a comparative analysis of the operational performance of a mesh type and radial type electrical network is performed. It is observed that the cumulative effect of forming a mesh type network along with a droop control strategy can further improve the voltage profile and contribute to increase photovoltaic penetration. The results are verified using an experimental setup of digital real-time simulator and power hardware-in-loop test methods. The results from this work will be useful for estimating the appropriate photovoltaic hosting capacity within a distribution network and implementation of a droop control strategy in power conditioning devices to maintain the network operational parameters within the specified limits. Highlights Voltage and line loading constraints’ combination can reduce PV hosting capacity by 50% as compared to only voltage as a constraint. Implementation of reactive power versus voltage droop control in PV power conditioning device can reduce voltage variation from 9% to 4%. In a PV integrated electrical energy network, line loading can be reduced by 20% if the network is configured from radial to mesh type.

scholarly journals Mitigation of Voltage Dip and Voltage Flickering by Multilevel D-STATCOM

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
M. S. Ballal ◽  
H. M. Suryawanshi ◽  
T. Venkateswara Reddy
Keyword(s):  
Power Quality ◽  
Distribution System ◽  
Reactive Power ◽  
Distribution Network ◽  
Voltage Sag ◽  
Service Interruptions ◽  
Flexible Ac Transmission ◽  
Voltage Dip ◽  
Basic Power ◽  
Ac Transmission

The basic power quality problems in the distribution network are voltage sag (dip), voltage flickering, and the service interruptions. STATCOM is a Flexible AC Transmission Systems (FACTS) technology device which can independently control the flow of reactive power. This paper presents the simulation and analysis of a STATCOM for voltage dip and voltage flickering mitigation. Simulations are carried out in MATLAB/Simulink to validate the performance of the STATCOM. A comparison between the six-pulse inverter and the five-level diode-clamped inverter is carried out for the performance of 66/11 KV distribution system.

Sign in / Sign up

Export Citation Format

Share Document