scholarly journals Composite Materials. Mixed Mode(I+II) Fracture Toughness and Rate Dependent Fracture Behavior of Interlayer-Toughened Composite Laminate.

2001 ◽  
Vol 50 (5) ◽  
pp. 482-487
Author(s):  
Noriyo HORIKAWA ◽  
Takayuki KUSAKA ◽  
Masayoshi MASUDA
Keyword(s):  
Fracture Toughness ◽  
Composite Materials ◽  
Mixed Mode ◽  
Composite Laminate ◽  
Fracture Behavior ◽  
Mode I ◽  
Rate Dependent

scholarly journals Mixed-Mode Interlaminar Fracture Toughness of Glass and Carbon Fibre Powder Epoxy Composites—For Design of Wind and Tidal Turbine Blades

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2103
Author(s):  
Christophe Floreani ◽  
Colin Robert ◽  
Parvez Alam ◽  
Peter Davies ◽  
Conchúr M. Ó. Brádaigh
Keyword(s):  
Fracture Toughness ◽  
Carbon Fibre ◽  
Composite Structures ◽  
Mixed Mode ◽  
Epoxy Composites ◽  
Mode I ◽  
Mode Ii ◽  
Pure Mode ◽  
Interlaminar Fracture Toughness ◽  
Interlaminar Fracture

Powder epoxy composites have several advantages for the processing of large composite structures, including low exotherm, viscosity and material cost, as well as the ability to carry out separate melting and curing operations. This work studies the mode I and mixed-mode toughness, as well as the in-plane mechanical properties of unidirectional stitched glass and carbon fibre reinforced powder epoxy composites. The interlaminar fracture toughness is studied in pure mode I by performing Double Cantilever Beam tests and at 25% mode II, 50% mode II and 75% mode II by performing Mixed Mode Bending testing according to the ASTM D5528-13 test standard. The tensile and compressive properties are comparable to that of standard epoxy composites but both the mode I and mixed-mode toughness are shown to be significantly higher than that of other epoxy composites, even when comparing to toughened epoxies. The mixed-mode critical strain energy release rate as a function of the delamination mode ratio is also provided. This paper highlights the potential for powder epoxy composites in the manufacturing of structures where there is a risk of delamination.

Fracture assessment of polycarbonate parts produced by fused deposition modeling in the out-of-plane printing direction – effect of raster angle

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Iman Sedighi ◽  
Majid R. Ayatollahi ◽  
Bahador Bahrami ◽  
Marco A. Pérez-Martínez ◽  
Andrés A. Garcia-Granada
Keyword(s):  
Fracture Toughness ◽  
Finite Element ◽  
Fracture Behavior ◽  
Fused Deposition Modeling ◽  
Mode I ◽  
Content Type ◽  
Fused Deposition ◽  
Out Of Plane ◽  
Deposition Modeling ◽  
Fracture Tests

Purpose The purpose of this paper is to study the Mode I fracture behavior of polycarbonate (PC) parts produced using fused deposition modeling (FDM). The focus of this study is on samples printed along the out-of-plane direction with different raster angles. Design/methodology/approach Tensile and Mode I fracture tests were conducted. Semi-circular bend specimens were used for the fracture tests, which were printed in four different raster patterns of (0/90), (15/−75) (30/−60) and (45/−45). Moreover, the finite element method (FEM) was used to determine the applicability of linear elastic fracture mechanics (LEFM) for the printed PC parts. The fracture toughness results, as well as the fracture path and the fracture surfaces, were studied to describe the fracture behavior of the samples. Findings Finite element results confirm that the use of LEFM is allowed for the tested PC samples. The fracture toughness results show that changing the direction of the printed rasters can have an effect of up to 50% on the fracture toughness of the printed parts, with the (+45/−45) and (0/90) orientations having the highest and lowest resistance to crack propagation, respectively. Moreover, except for the (0/90) orientation, the other samples have higher crack resistance compared to the bulk material. The fracture toughness of the tested PC depends more on the toughness of the printed sample, rather than its tensile strength. Originality/value The toughness and the energy absorption capability of the printed samples (with different raster patterns) were identified as the main properties affecting the fracture toughness of the AM PC parts. Because the fracture resistance of almost all the samples was higher than that of the base material, it is evident that by choosing the right raster patterns for 3D-printed parts, very high resistance to crack growth may be obtained. Also, using FEM and comparing the size of the plastic zones, it was concluded that, although the tensile curves show nonlinearity, LEFM is still applicable for the printed parts.

Mixed-mode I/II fracture criterion for crack initiation assessment of composite materials

2018 ◽  
Vol 230 (1) ◽  
pp. 281-301 ◽  
Author(s):  
Mahdi Fakoor ◽  
Hannaneh Manafi Farid
Keyword(s):  
Composite Materials ◽  
Crack Initiation ◽  
Mixed Mode ◽  
Fracture Criterion ◽  
Mode I
Sign in / Sign up

Export Citation Format

Share Document