scholarly journals On the Shearing Residual Stress of Straightened Wires

1962 ◽  
Vol 11 (108) ◽  
pp. 543-547
Author(s):  
Shigeru YONETANI ◽  
Yukio SATO ◽  
Yoji FUJITA
Keyword(s):  
Residual Stress

TEM investigations of surface residual stress relaxation in A12O3 and Al2O3-SiC nanocomposite

1994 ◽  
Vol 52 ◽  
pp. 628-629
Author(s):  
J. Fang ◽  
H. M. Chan ◽  
M. P. Harmer
Keyword(s):  
Residual Stress ◽  
Single Phase ◽  
Stress Relief ◽  
Stress Recovery ◽  
Surface Residual Stress ◽  
Microscopic Mechanism ◽  
Sic Particles ◽  
Annealing Procedure ◽  
The Difference ◽  
Nano Size

It was Niihara et al. who first discovered that the fracture strength of Al2O3 can be increased by incorporating as little as 5 vol.% of nano-size SiC particles (>1000 MPa), and that the strength would be improved further by a simple annealing procedure (>1500 MPa). This discovery has stimulated intense interest on Al2O3/SiC nanocomposites. Recent indentation studies by Fang et al. have shown that residual stress relief was more difficult in the nanocomposite than in pure Al2O3. In the present work, TEM was employed to investigate the microscopic mechanism(s) for the difference in the residual stress recovery in these two materials.Bulk samples of hot-pressed single phase Al2O3, and Al2O3 containing 5 vol.% 0.15 μm SiC particles were simultaneously polished with 15 μm diamond compound. Each sample was cut into two pieces, one of which was subsequently annealed at 1300° for 2 hours in flowing argon. Disks of 3 mm in diameter were cut from bulk samples.

Residual stress measurements and modeling of built-up Box-T sections

2021 ◽  
Vol 160 ◽  
pp. 107336
Author(s):  
Ziqian Zhang ◽  
Gang Shi ◽  
Xuesen Chen ◽  
Lijun Wang ◽  
Le Zhou
Keyword(s):  
Residual Stress ◽  
Stress Measurements

Comparative study of the effective parameters on residual stress relaxation in welded aluminum plates under cyclic loading

2020 ◽  
Vol 21 (5) ◽  
pp. 505
Author(s):  
Yousef Ghaderi Dehkordi ◽  
Ali Pourkamali Anaraki ◽  
Amir Reza Shahani
Keyword(s):  
Residual Stress ◽  
Cyclic Loading ◽  
Stress Relaxation ◽  
Stress Amplitude ◽  
Cyclic Plasticity ◽  
Mean Stress ◽  
Effective Parameters ◽  
Perfect Plasticity ◽  
Residual Stress Relaxation ◽  
Aluminum Plates

The prediction of residual stress relaxation is essential to assess the safety of welded components. This paper aims to study the influence of various effective parameters on residual stress relaxation under cyclic loading. In this regard, a 3D finite element modeling is performed to determine the residual stress in welded aluminum plates. The accuracy of this analysis is verified through experiment. To study the plasticity effect on stress relaxation, two plasticity models are implemented: perfect plasticity and combined isotropic-kinematic hardening. Hence, cyclic plasticity characterization of the material is specified by low cycle fatigue tests. It is found that the perfect plasticity leads to greater stress relaxation. In order to propose an accurate model to compute the residual stress relaxation, the Taguchi L18 array with four 3-level factors and one 6-level is employed. Using statistical analysis, the order of factors based on their effect on stress relaxation is determined as mean stress, stress amplitude, initial residual stress, and number of cycles. In addition, the stress relaxation increases with an increase in mean stress and stress amplitude.

Residual stress and elastic anisotropy in the Ti-Al-(Si-)N and Cr-Al-(Si-)N nanocomposites deposited by cathodic arc evaporation

2008 ◽  
Vol 2008 (27) ◽  
pp. 245-252 ◽  
Author(s):  
M. Dopita ◽  
Ch. Wüstefeld ◽  
V. Klemm ◽  
G. Schreiber ◽  
D. Heger ◽  
...  
Keyword(s):  
Residual Stress ◽  
Elastic Anisotropy ◽  
Cathodic Arc Evaporation ◽  
Arc Evaporation ◽  
Cathodic Arc

Residual stress distribution in laser alloying zone with FeCSiB powder

2008 ◽  
Author(s):  
Zhengyang Li ◽  
Haiyan Zhao ◽  
Minlin Zhong ◽  
Bin Zhang ◽  
Yu Gu ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Laser Alloying

The Residual Stress Behavior in Fatigue Process of 80kg/mm2 High Tensile Strength Steels

1967 ◽  
Vol 16 (171) ◽  
pp. 926-930
Author(s):  
Fumiaki KANZAKI ◽  
Nozomu NAWATA ◽  
Hajime KITAGAWA
Keyword(s):  
Residual Stress ◽  
Tensile Strength ◽  
High Tensile Strength ◽  
Fatigue Process ◽  
Stress Behavior
Sign in / Sign up

Export Citation Format

Share Document