scholarly journals Preparation of Ruthenium Aluminide Powder by Mechanical Alloying and the Properties of the RuAl Compact Consolidated by Plasma Activated Sintering Process.

1995 ◽  
Vol 42 (11) ◽  
pp. 1283-1288
Author(s):  
Akihiro Matsumoto ◽  
Kunisuke Andoh ◽  
Kiyotaka Katoh
Keyword(s):  
Mechanical Alloying ◽  
Sintering Process ◽  
Activated Sintering ◽  
Ruthenium Aluminide ◽  
Plasma Activated Sintering

Dry sliding wear behavior of Fe3Al alloys prepared by mechanical alloying and plasma activated sintering

Wear ◽  
2010 ◽  
Vol 268 (3-4) ◽  
pp. 473-480 ◽  
Author(s):  
Jian Wang ◽  
Jiandong Xing ◽  
Li Cao ◽  
Wei Su ◽  
Yimin Gao
Keyword(s):  
Mechanical Alloying ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Activated Sintering ◽  
Plasma Activated Sintering

Rapid consolidation of BiPbSrCaCuO powders by a plasma activated sintering process

1994 ◽  
Vol 26 (1) ◽  
pp. 55-60 ◽  
Author(s):  
Chien-Hua Shan ◽  
Subhash H. Risbud ◽  
Kazuo Yamazaki ◽  
Kazuo Shoda
Keyword(s):  
Sintering Process ◽  
Activated Sintering ◽  
Plasma Activated Sintering

Thermoelectric properties of p-type Te-doped (Bi,Sb)2Te3 alloys by mechanical alloying and plasma activated sintering

2008 ◽  
Vol 448 (1-2) ◽  
pp. 308-312 ◽  
Author(s):  
Xi’an Fan ◽  
Junyou Yang ◽  
Wen Zhu ◽  
Siqian Bao ◽  
Xingkai Duan ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Thermoelectric Properties ◽  
Activated Sintering ◽  
P Type ◽  
Plasma Activated Sintering

Preparation Technology and Mechanical Properties of Fe-C Composites Fabricated by Plasma Activated Sintering

2013 ◽  
Vol 345 ◽  
pp. 223-227
Author(s):  
Gui Wu Liu ◽  
Chong Jian Zhou ◽  
San Tuan Zhao ◽  
Kuo Zhang ◽  
Zhi Guo Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Applied Pressure ◽  
High Energy ◽  
Sintering Process ◽  
Preparation Technology ◽  
Activated Sintering ◽  
Powder Composition ◽  
Original Powder ◽  
Plasma Activated Sintering

The Fe-C composites were fabricated by a combination of high-energy ball milling of Fe-C powder mixtures and plasma activated sintering process. An orthogonal experiment in four factors (including original powder composition, sintering temperature, applied pressure and holding time) and three levels was employed to investigate the effects of preparation technology on mechanical properties (bending strength and hardness) of the Fe-C composite. The experimental results show that the crystalline Fe3C phase can be produced by the rapid sintering process, though it is cannot form theoretically due to the high Gibbs free energy, and more or less holes and composition segregation phenomenon coexist in the composite. The original powder composition plays the leading role in both the mechanical properties of the Fe-C composites. However, the effects of the other parameters on the bending strength and hardness of the composite are somewhat different. The optimal technology combinations for the bending strength and hardness are obtained as follows: 50Fe+50Fe3C/1373 K/400 s/20 MPa and 50Fe+50Fe3C/50 MPa/1273 K/400 s, respectively.

Sign in / Sign up

Export Citation Format

Share Document