Numerical simulation of the wind tunnel environment by a panel method

1980 ◽  
Author(s):  
K. LEE
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Panel Method

Numerical Simulation of Flowfield around High Speed Trains Passing by each other at the same Speed

2011 ◽  
Vol 97-98 ◽  
pp. 698-701
Author(s):  
Ming Lu Zhang ◽  
Yi Ren Yang ◽  
Li Lu ◽  
Chen Guang Fan
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Flow Field ◽  
Point Source ◽  
High Speed ◽  
Stokes Equations ◽  
Field Structure ◽  
Vehicle Speed ◽  
Mesh Method ◽  
High Speed Trains

Large eddy simulation (LES) was made to solve the flow around two simplified CRH2 high speed trains passing by each other at the same speed base on the finite volume method and dynamic layering mesh method and three dimensional incompressible Navier-Stokes equations. Wind tunnel experimental method of resting train with relative flowing air and dynamic mesh method of moving train were compared. The results of numerical simulation show that the flow field structure around train is completely different between wind tunnel experiment and factual running. Two opposite moving couple of point source and point sink constitute the whole flow field structure during the high speed trains passing by each other. All of streamlines originate from point source (nose) and finish with the closer point sink (tail). The flow field structure around train is similar with different vehicle speed.

The Influence of the Convective Terms Discretization Scheme on the Simulation Results of Architectural Numerical Wind Tunnel

2012 ◽  
Vol 204-208 ◽  
pp. 4884-4887
Author(s):  
Jian Feng Wu ◽  
Cai Hua Wang ◽  
Chang Li Song
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Building Structures ◽  
Discretization Scheme ◽  
Shape Coefficient ◽  
Fluent Software ◽  
Actual Operation ◽  
Simulation Results ◽  
Load Shape ◽  
Numerical Wind Tunnel Method

The numerical simulation of construction is to obtain the desired accuracy. It depends on the theoretical basis of the calculator and selection of the various important factors in the actual operation. For this problem, this paper adopting the current code for the design of building structures as the comparison standard, using the FLUENT software, taking the numerical simulation results of a high building’s wind load shape coefficient of for example, discussing the influence of four kinds of the convective terms discretization scheme, respectively the first-order upwind, the second order upwind , power law and Quadratic upwind interpolation for convective kinematics, on the simulation results of architectural numerical wind tunnel, provides the reference for the rational use of numerical wind tunnel method.

Numerical Simulation of an Adaptive Wall in a Virtual Transonic Wind Tunnel

AIAA Journal ◽  
2017 ◽  
Vol 55 (9) ◽  
pp. 3214-3218 ◽  
Author(s):  
P. Weiand ◽  
S. Michelis ◽  
A. D. Gardner
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Transonic Wind Tunnel

scholarly journals The Problem of Airflow Around Building Clusters in Different Configurations

2017 ◽  
Vol 64 (3) ◽  
pp. 401-418 ◽  
Author(s):  
Mateusz Jędrzejewski ◽  
Marta Poćwierz ◽  
Katarzyna Zielonko-Jung
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Pressure Measurement ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Complex Model ◽  
Stress Model ◽  
Qualitative Information ◽  
Pressure Coefficients ◽  
Rsm Model

Abstract In the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have shown that, in this specific case, a more complex model of turbulence is not necessary. The results obtained with this model are not more accurate than the ones obtained using the RKE model. The model, scale 1:400, was tested in a wind tunnel. The pressure measurement near buildings, oil visualization and scour technique were undertaken and described accordingly. Measurements gave the quantitative and qualitative information describing the nature of the flow. Finally, the data were compared with the results of the experiments performed. The pressure coefficients resulting from the experiment were compared with the coefficients obtained from the numerical simulation. At the same time velocity maps and streamlines obtained from the calculations were combined with the results of the oil visualisation and scour technique.

scholarly journals Numerical Simulation and Wind Tunnel Investigation on Static Characteristics of VAWT Rotor Starter with Lift-Drag Combined Structure

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6167
Author(s):  
Fang Feng ◽  
Guoqiang Tong ◽  
Yunfei Ma ◽  
Yan Li
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Speed Ratio ◽  
Static Characteristics ◽  
Torque Coefficient ◽  
Starting Characteristics ◽  
Static Torque

In order to get rid of the impact of the global financial crisis and actively respond to global climate change, it has become a common choice for global economic development to develop clean energy such as wind energy, improve energy efficiency and reduce greenhouse gas emissions. With the advantages of simple structure, unnecessary facing the wind direction, and unique appearance, the vertical axis wind turbine (VAWT) attracts extensive attention in the field of small and medium wind turbines. The lift-type VAWT exhibits outstanding aerodynamic characteristics at a high tip speed ratio, while the starting characteristics are generally undesirable at a low wind speed; thus, how to improve the starting characteristics of the lift-type VAWT has always been an important issue. In this paper, a lift-drag combined starter (LDCS) suitable for lift-type VAWT was proposed to optimize the starting characteristics of lift-type VAWT. With semi-elliptical drag blades and lift blades equipped on the middle and rear part outside the starter, the structure is characterized by lift-drag combination, weakening the adverse effect of the starter with semi-elliptical drag blades alone on the output performance of the original lift-type VAWT and improving the characteristics of the lift-drag combined VAWT. The static characteristic is one of the important starting characteristics of the wind turbine. The rapid development of computational fluid dynamics has laid a solid material foundation for VAWT. Thus the static characteristics of the LDCS with different numbers of blades were investigated by conducting numerical simulation and wind tunnel tests. The results demonstrated that the static torque coefficient of LDCS increased significantly with the increased incoming wind speed. The average value of the static torque coefficient also increased significantly. This study can provide guidelines for the research of lift-drag combined wind turbines.

Characterisation of a highly staggered spanwise cambered biplane

2015 ◽  
Vol 119 (1212) ◽  
pp. 203-228
Author(s):  
L.W. Traub ◽  
R. Waghela ◽  
K.A. Bordignon
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Dihedral Angles ◽  
Wind Tunnel Testing ◽  
High Lift ◽  
Front Wing ◽  
Geometric Variation ◽  
Tunnel Testing

AbstractAn investigation is presented to elucidate the performance of a staggered, spanwise cambered biplane. The spanwise camber yielded wings forming a ‘∧’ or ‘∨’ when viewed streamwise. The configuration is examined in terms of its aerodynamic and stability characteristics. The feasibility of negating the requirement for a conventional empennage is explored. Geometric variation encompassed front and back wing anhedral/dihedral angles yielding 49 combinations. Evaluation of the geometry was accomplished using both wind tunnel testing and numerical simulation. The results indicated that front wing dihedral in conjunction with aft wing anhedral was most beneficial, such that the benefit of wake spacing was maximised. Aerodynamic benefit was indicated compared to a conventional empennage geometry. The greatest disparity in behaviour of the fore and aft wing anhedral/dihedral distribution was in the high lift regime, where the nature of the stall varied. Simulations to establish the viability of the geometry in terms of controllability were also conducted and indicated that the configuration is viable.

Sign in / Sign up

Export Citation Format

Share Document