Effects of Mach number and Reynolds number on leading-edge vortices at high angle-of-attack

1988 ◽  
Author(s):  
KARL SCHRADER ◽  
GREGORY REYNOLDS ◽  
CHARLES NOVAK
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Angle Of Attack ◽  
Leading Edge ◽  
High Angle ◽  
High Angle Of Attack ◽  
Leading Edge Vortices

Plasma Flow Control Simulation of an Airfoil of Wind Turbine at an Intermediate Reynolds Number

2013 ◽  
Author(s):  
Hikaru Aono ◽  
Taku Nonomura ◽  
Aiko Yakeno ◽  
Kozo Fujii ◽  
Koichi Okada
Keyword(s):  
Reynolds Number ◽  
Flow Control ◽  
Wind Turbine ◽  
Shear Layer ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Plasma Actuator ◽  
Dominant Factor ◽  
High Angle ◽  
High Angle Of Attack

The flow over a National Renewable Energy Laboratory S825 airfoil was simulated for a chord Reynolds number of 7.5×105 and an angle of attack of 22.1 deg. These conditions approximately matched a blade element condition of 75% radius of 42-m-diameter wind turbine operating 2.5 rpm under a free-stream of 10 m/s. Computed flow of the uncontrolled case characterized massive separation from near the leading edge due to high angle of attack. With the active flow control by a dielectric barrier discharge plasma actuator, separation was reduced and the lift-to-drag ratio increased from 2.25 to 6.52. Impacts of the plasma actuator on the shear layer near the leading edge were discussed. Direct momentum addition provided by the case setup of plasma actuator considered in current study seemed to be a dominant factor to prevent the separation of shear layer near the leading edge rather than influence of small disturbances induced by the plasma actuator operated in a burst modulation. However, due to the high angle of attack and the thick airfoil, the control authority of the plasma actuator with the setup (i.e. the operating condition and number of plasma actuators installed on the wing surface) considered was insufficient to completely suppress the separation over the NREL S825 airfoil.

scholarly journals Leading Edge Blowing to Mimic and Enhance the Serration Effects for Aerofoil

2021 ◽  
Vol 11 (6) ◽  
pp. 2593
Author(s):  
Yasir Al-Okbi ◽  
Tze Pei Chong ◽  
Oksana Stalnov
Keyword(s):  
Boundary Layer ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Shear Instability ◽  
Vortical Flow ◽  
High Angle ◽  
High Angle Of Attack ◽  
Layer Separation ◽  
Aerodynamic Performances

Leading edge serration is now a well-established and effective passive control device for the reduction of turbulence–leading edge interaction noise, and for the suppression of boundary layer separation at high angle of attack. It is envisaged that leading edge blowing could produce the same mechanisms as those produced by a serrated leading edge to enhance the aeroacoustics and aerodynamic performances of aerofoil. Aeroacoustically, injection of mass airflow from the leading edge (against the incoming turbulent flow) can be an effective mechanism to decrease the turbulence intensity, and/or alter the stagnation point. According to classical theory on the aerofoil leading edge noise, there is a potential for the leading edge blowing to reduce the level of turbulence–leading edge interaction noise radiation. Aerodynamically, after the mixing between the injected air and the incoming flow, a shear instability is likely to be triggered owing to the different flow directions. The resulting vortical flow will then propagate along the main flow direction across the aerofoil surface. These vortical flows generated indirectly owing to the leading edge blowing could also be effective to mitigate boundary layer separation at high angle of attack. The objectives of this paper are to validate these hypotheses, and combine the serration and blowing together on the leading edge to harvest further improvement on the aeroacoustics and aerodynamic performances. Results presented in this paper strongly indicate that leading edge blowing, which is an active flow control method, can indeed mimic and even enhance the bio-inspired leading edge serration effectively.

Instantaneous topology of the unsteady leading-edge vortex at high angle of attack

AIAA Journal ◽  
1993 ◽  
Vol 31 (8) ◽  
pp. 1384-1391 ◽  
Author(s):  
C. Magness ◽  
O. Robinson ◽  
D. Rockwell
Keyword(s):  
Angle Of Attack ◽  
Leading Edge ◽  
High Angle ◽  
High Angle Of Attack ◽  
Leading Edge Vortex ◽  
Edge Vortex

Sweep Effects on Fan-Intake Aerodynamics at High Angle of Attack

2021 ◽  
Author(s):  
Ben Mohankumar ◽  
Cesare A. Hall ◽  
Mark J. Wilson
Keyword(s):  
Mach Number ◽  
Pressure Ratio ◽  
Angle Of Attack ◽  
Pressure Rise ◽  
Low Pressure ◽  
Rotating Stall ◽  
High Angle ◽  
High Angle Of Attack ◽  
Mach Numbers ◽  
High Mach

Abstract Sweep in a transonic fan is conventionally used to reduce design point losses by inclining the passage shock relative to the incoming flow. However, future low pressure ratio fans operate to lower Mach numbers meaning the role of sweep at cruise is diminished. Instead, sweep might be repurposed to improve the performance of critical high Mach number off-design conditions such as high angle of attack (AOA). In this paper, we use unsteady computational fluid dynamics to compare two transonic low pressure ratio fans, one radially stacked and one highly swept, coupled to a short intake design, at the high AOA flight condition. The AOA considered is 35°, which is sufficient to separate the intake bottom lip. The midspan of the swept fan was shifted upstream to add positive sweep to the outer span. Based on previous design experience, it was hypothesised the swept fan would reduce transonic losses when operating at high AOA. However, it was found the swept fan increased the rotor loss by 24% relative to the radial fan. Loss was increased through two key mechanisms. i) Rotor choking: flow is redistributed around the intake separation and enters the rotor midspan with high Mach numbers. Sweeping the fan upstream reduced the effective intake length, which increased the inlet relative Mach number and amplified choking losses. ii): Rotor-separation interaction (RSI): the rotor tip experiences low mass flow inside the separation, which increases the pressure rise across the casing to a point where the boundary layer separates. The swept fan diffused the casing streamtube, causing the casing separation to increase in size and persist in the passage for longer. High RSI loss indicated the swept fan was operating closer to the rotating stall point.

scholarly journals Power reduction and the radial limit of stall delay in revolving wings of different aspect ratio

2015 ◽  
Vol 12 (105) ◽  
pp. 20150051 ◽  
Author(s):  
Jan W. Kruyt ◽  
GertJan F. van Heijst ◽  
Douglas L. Altshuler ◽  
David Lentink
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Angle Of Attack ◽  
Radial Distance ◽  
Leading Edge ◽  
High Angle ◽  
High Angle Of Attack ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Low Aspect Ratio Wings

Airplanes and helicopters use high aspect ratio wings to reduce the power required to fly, but must operate at low angle of attack to prevent flow separation and stall. Animals capable of slow sustained flight, such as hummingbirds, have low aspect ratio wings and flap their wings at high angle of attack without stalling. Instead, they generate an attached vortex along the leading edge of the wing that elevates lift. Previous studies have demonstrated that this vortex and high lift can be reproduced by revolving the animal wing at the same angle of attack. How do flapping and revolving animal wings delay stall and reduce power? It has been hypothesized that stall delay derives from having a short radial distance between the shoulder joint and wing tip, measured in chord lengths. This non-dimensional measure of wing length represents the relative magnitude of inertial forces versus rotational accelerations operating in the boundary layer of revolving and flapping wings. Here we show for a suite of aspect ratios, which represent both animal and aircraft wings, that the attachment of the leading edge vortex on a revolving wing is determined by wing aspect ratio, defined with respect to the centre of revolution. At high angle of attack, the vortex remains attached when the local radius is shorter than four chord lengths and separates outboard on higher aspect ratio wings. This radial stall limit explains why revolving high aspect ratio wings (of helicopters) require less power compared with low aspect ratio wings (of hummingbirds) at low angle of attack and vice versa at high angle of attack.

On the Vortex Breakdown Phenomenon in High Angle of Attack Flows Over Delta Wing Geometries

2014 ◽  
Author(s):  
Eric D. Robertson ◽  
Varun Chitta ◽  
D. Keith Walters ◽  
Shanti Bhushan
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
High Angle ◽  
High Angle Of Attack ◽  
Eddy Simulation ◽  
Wing Model

Using computational methods, an investigation was performed on the physical mechanisms leading to vortex breakdown in high angle of attack flows over delta wing geometries. For this purpose, the Second International Vortex Flow Experiment (VFE-2) 65° sweep delta wing model was studied at a root chord Reynolds number (Recr) of 6 × 106 at various angles of attack. The open-source computational fluid dynamics (CFD) solver OpenFOAM was used in parallel with the commercial CFD solver ANSYS® FLUENT. For breadth, a variety of classic closure models were applied, including unsteady Reynolds-averaged Navier-Stokes (URANS) and detached eddy simulation (DES). Results for all cases are analyzed and flow features are identified and discussed. The results show the inception of a pair of leading edge vortices originating at the apex for all models used, and a region of steady vortical structures downstream in the URANS results. However, DES results show regions of massively separated helical flow which manifests after vortex breakdown. Analysis of turbulence quantities in the breakdown region gives further insight into the mechanisms leading to such phenomena.

Sign in / Sign up

Export Citation Format

Share Document