Effects of Non-Axisymmetric Volute On Rotating Stall in the Vaneless Diffuser of Centrifugal Compressors

Rotating stall is an important unstable flow phenomenon that leads to performance degradation and limits the stability boundary in centrifugal compressors. The volute is one of the sources inducing non-axisymmetric flows in centrifugal compressors, which has an important effect on compressors' aerodynamic performance. However, the influence of volute on rotating stall is unclear. Therefore, the effects of volute on rotating stall behavior have been explored in this paper by experiments and numerical simulations. The frequency of the rotating stall captured by the experiments is 43.9% of the impeller passing frequency, while it is 44.7% of IPF calculated from the numerical results, which proves the accuracy and capability of the numerical method in this work to study the rotating stall behavior. The flow fields from CFD simulations further reveal that one stall cell initializing in a particular location deforms into several stall cells while rotating along the circumferential direction and becomes much smaller in a specific location during the evolution process, and finally, it is suppressed in another specific location as a result of the distorted flow field caused by the volute. By optimizing volute geometry to reduce the distortion of the flow field, it is expected that the rotating stall can be weakened or suppressed, which is helpful to extend the stable operating range of centrifugal compressors.

Aeroelastic aspects of Axial Compressor Stage with Self-Recirculating Casing Treatment

For successful implementation of casing treatment designs in axial compressors, apart from the stall margin improvement benefits, aeroelasticity also plays a major role. This manuscript addresses the not often discussed aeroelastic aspects of a new discrete type of passive Self-Recirculating Casing Treatment (RCT) designed for a transonic axial compressor stage. Experiments are carefully designed for synchronized measurement of the unsteady fluidic disturbances and vibrations during rotating stall for compressor with baseline solid casing and Self-RCT. The modal characteristics of the axial compressor rotor-disk assembly are studied experimentally and numerically. Experimentally it is observed that the rotating stall cells excite the blades in their fundamental mode in a compressor with baseline solid casing at the stall flow condition. In contrast, there is no excitation of the blades in the compressor with self-recirculating casing treatment at the same solid casing stall flow condition. Also, the self-recirculating casing treatment compared to the solid casing can significantly reduce the overall vibration levels of the blades that are excited at the stall flow condition. The casing treatment is able to alter the flow field near the tip region of the rotor blade, and hence influencing the forcing function of the rotating cantilever blades to have the aeroelastic benefit.

Numerical Analysis of a Novel Twin-Impeller Centrifugal Compressor

Centrifugal compressors are widely used in many industrial fields such as automotive, aviation, aerospace. However, these turbomachines suffer instability phenomenon when the flow rate is too high or too low, called rotating stall and surge. These phenomena cause the operation failure, pressure fluctuations and vibrations of the thorough system. Numerous mechanical solutions have been presented to minimize these instabilities and expand the operating range towards low-flow rates like active control of the flow path, variable inlet guide vane and casing treatment. Currently, our team has developed a novel compressor composed of a twin-impeller powered by autonomous systems. We notice the performance improvement and instabilities suppression of this compressor experimentally. In this paper, an active control method is introduced by controlling the speed and rotation direction of the impellers to expand the operating range. A CFD study is then conducted to analysis flow morphology and thermodynamic characteristics based on the experimental observations at three special points. Numerical results and experimental measurements of compressor maps are consistent.

INVESTIGATION ON MODE CHARACTERISTICS OF ROTATING INSTABILITY AND ROTATING STALL IN AN AXIAL COMPRESSOR

Rotating instability (RI) and rotating stall (RS) are two types of aerodynamic instability in axial compressors. The former features the side-by-side peaks below the blade passing frequency (BPF) in frequency spectra, and the latter represents one or more stall cells rotating in the compressor. This paper presents an experimental on the nearfield pressure and farfield acoustic characteristics of RI phenomenon in a low-speed axial compressor rotor, which endures both RI and RS at several working conditions. In order to obtain the high-order modes of RI and other aerodynamic instability, a total of 9 or 20 Kulites are circumferentially mounted on the casing wall to measure the nearfield pressure fluctuation using a mode order calibration method. Meantime in the farfield 16 microphones are planted to measure the acoustic mode order using the compressive sensing method. Through calibration the experiments acquire the mode orders generated by RI and the interaction between RI and BPF, which is higher than the number of transducers. As for RS, the mode decomposition shows a mode order of 1, indicating one single stall cell rotating in the compressor. This experiment also shows that amplitude of RI modes is decreased when RS occurs, but RS modes and RI modes will both be enhanced if the flow rate is further reduced. This experiment reveals that RI experiences three stages of “strengthen-weaken-strengthen”, and hence RI may not be regarded only as “prestall” disturbance.

Experimental Investigation of Rotating Instability in an Axial Compressor with a Steady Swirl Distortion Inlet

In this paper, an experimental study was carried out on the rotating instability in an axial compressor subjected to inlet steady paired swirl distortion. In order to deepen the understanding of the rotating stall mechanism under inlet steady paired swirl distortion, the dynamic-wall static pressure near the rotor tip was monitored to characterize the flow in the rotor tip region at different circumferential stations. In the experiment, the dynamic characteristics of the rotor tip flow field at a stable operating point and during the process from the stable point to complete stall were measured. The results indicated that for the compressor with a 2 mm rotor tip clearance, the inlet paired swirl distortion induced rotating instability (RI) near the stall point, causing the compressor to enter stall in advance. Compared with the RI intensity of the clean inlet, the distortion with a swirling blade stagger angle (αst) of ±20° increased the RI intensity up to 69.8%, while for αst equal to ±40°, the RI intensity increased at most by 135.8%. As the rotor tip clearance increased to 3 mm, the co-rotating swirl in the paired swirl distortion inhibited the appearance of RI, while the counter-rotating part aggravated the development of RI. At the beginning, the process of the compressor rotating stall involved the alternation of short-scale disturbance and long-scale disturbance. The co-rotating swirl weakened the perturbation propagated from the counter-rotating swirl sector. Once the inhibition was no longer present, the short-scale disturbance rapidly developed into a long-scale disturbance and then entered the rotating stall.

A Method of Stall and Surge Prediction in Axial Compressors Based On Three-Dimensional Body-Force Model

The occurrence of stall and surge in axial compressors has a great impact on the performance and reliability of aero-engines. Accurate and efficient prediction of the key features during these events has long been the focus of engine design processes. In this paper, a new body-force model that can capture the three-dimensional and unsteady features of stall and surge in compressors at a fraction of time required for URANS computations is proposed. To predict the rotating stall characteristics, the deviation of local airflow angle from the blade surface is calculated locally during the simulation. According to this local deviation, the computational domain is divided into stalled and forward flow regions, and the body-force field is updated accordingly; to predict the surge characteristics, the local airflow direction is used to divide the computational domain into reverse flow regions and forward flow regions. A single-stage axial compressor and a three-stage axial compressor are used to verify the proposed model. The results show that the method is capable of capturing stall and surge characteristics correctly. Compared to the traditional fully three-dimensional URANS method (fRANS), the simulation time for multi-stage axial compressors is reduced by 1 to 2 orders of magnitude.

Experimental and Numerical Analysis of a Compressor Stage under Flow Distortion

On many occasions, fan or compressor stages have to face azimuthal flow distortion at inlet, which affects their performance and stability. These flow distortions can be caused by external events or by some particular geometrical features. The aim of this work is to propose a joined numerical and experimental analysis of the flow behavior in a single axial compressor stage under flow distortion. The distortions are generated by different grids that are placed upstream to the rotor. Experimentally, the flow analysis is based on the measurements obtained by a series of unsteady pressure sensors flush-mounted at the casing of the machine rotor. URANS computations are conducted using the elsA software. The flow distortion is simulated by a drop of stagnation pressure ratio at the inlet boundary condition. The study is focusing first on the ability of a pressure drop, imposed as an inlet boundary condition in CFD, to reproduce accurately the effect of a flow distortion. The analysis is conducted using singular value decomposition (SVD) and dynamic mode decomposition (DMD). A special attention is then paid, on the experimental level, to the arising of rotating stall, from the onset of the instability up to completely developed stall cells.

Gas Turbine Aerodynamics Improvement Via a Design of Intelligent Fractional Control

Gas turbines are complex processes characterized by the instability and uncertainty of various sources. The range of useful operating in an axial compressor which is part of a turbine gas is limited by aerodynamic instabilities that are surge and rotating stall. This paper presents two intelligent fractional order sliding mode controllers. At first, a robust sliding fractional surface form is proposed to deal with hazardous phenomena which limit compression systems performance, and speed transitions, which can lead to temporary stall development, pressure drop at the output, degrade the effective operation of compressors and consequently gas turbines. Second, to reduce the chattering/fluctuation in control, a fuzzy logic and finite time criterion are used as switching control at the reaching phase in the sliding mode control. Additionally, the controller gains are obtained by offline multi-objective Particle swarm optimization (MOPSO) search. Finally, the surge and rotating stall of a Variable Speed Axial Compressor (VSAC) in a gas turbine are investigated under the system nonlinearities and also in presence of an external disturbance and perturbations. The simulation results signify the performance of the two MOPSO-based fractional sliding mode controllers.