Exploration of Two-Phase Flow Structures in an Aluminum Nozzle of an Aerated-Liquid Injector Using X-Ray Fluorescence Techniques

2020 ◽  
Author(s):  
Kuo-Cheng Lin ◽  
Alan Kastengren ◽  
Campbell D. Carter
2020 ◽  
Vol 32 (11) ◽  
pp. 113310 ◽  
Author(s):  
Guangjian Zhang ◽  
Ilyass Khlifa ◽  
Kamel Fezzaa ◽  
Mingming Ge ◽  
Olivier Coutier-Delgosha

1996 ◽  
Vol 464 ◽  
Author(s):  
E. H. Kawamoto ◽  
Po-Zen Wong

ABSTRACTWe have carried out x-ray radiography and computed tomography (CT) to study two-phase flow in 3-D porous media. Air-brine displacement was imaged for drainage and imbibition experiments in a vertical column of glass beads. By correlating water saturation Sw with resistance R, we find that there is a threshold saturation S* ≈ 0.2, above which R(SW) ∼ Sw−2, in agreement with the empirical Archie relation. This holds true for both drainage and imbibition with littlehysteresis, provided that Sw remains above S*. Should Sw drop below S* during drainage, R(Sw) rises above the Archie prediction, exhibiting strong hysteresis upon reimbibition. This behavior suggests a transition in the connectivity of the water phase near S*, possibly due to percolation effects.


2007 ◽  
Vol 27 (Supplement1) ◽  
pp. 109-110
Author(s):  
Junichi UEMATSU ◽  
Kazuya ABE ◽  
Xiaoran YU ◽  
Tatsuya HAZUKU ◽  
Masaki OSHIMA ◽  
...  

2021 ◽  
Author(s):  
Mingming Ge ◽  
Guangjian Zhang ◽  
Navid Nematikourabbasloo ◽  
Kamel Fezzaa ◽  
Olivier Coutier-Delgosha

Hydrodynamic cavitation is a complex two-phase flow phenomenon involving mass and heat transfer between liquid and vapor. It occurs in many widely-used hydraulic machines, such as pumps and marine propellers, and often leads to undesired effects like material erosion, noise, and vibration. To control these detrimental effects, the visualization of two-phase flow morphology inside the opaque cavity is a crucial point to improve the physical and numerical models of cavitation. The major challenge in experimental measurements of cavitating flow fields is the fact that multiple scattering and a direct reflection of visible light from phase boundaries make the flow optically opaque. In recent years, unlike traditional local measurements using various probes, the development of the third-generation synchrotron radiation sources promotes the application of Xray phase-contrast imaging, which enables clear visualization of boundaries between phases with different refractive indices. In this study, the partial cavity is formed in a convergent-divergent (Venturi) channel with a small contraction ratio where the relatively stable cavitation regime can be sustained in a wide range of cavitation numbers. The experiment performed at Advanced Photon Source (APS) of Argonne uses the short high-flux X-ray pulses emitted from synchrotron sources to capture fast dynamic events and minimize motion blur. The internal two-phase structures and bubble development dynamics inside the quasi-stable sheet cavitation can be identified. Aside from the detailed illustration of two-phase morphology, X-ray phase-contrast images were also used to perform velocimetry by tracking either seeded particles or phase interfaces inside the opaque regions. Through appropriate postprocessing to the recorded X-ray images of cavitation, the time resolved velocity and void fraction fields are obtained simultaneously. These unprecedented experimental data will be further explored in understanding fluid mechanics underneath the cavity, estimating slip velocity between fluid-vapor interactions, and reconstructing pressure fields for compressible flows.


Author(s):  
Kenichi Katono ◽  
Jun Nukaga ◽  
Takuji Nagayoshi ◽  
Kenichi Yasuda

We have been developing a void fraction distribution measurement technique using the three-dimensional (3D) time-averaged X-ray CT (computed tomography) system to understand two-phase flow behavior inside a fuel assembly for BWR (boiling water reactor) thermal hydraulic conditions of 7.2 MPa and 288 °C. Unlike CT images of a normal standstill object, we can obtain 3D CT images that are reconstructed from time-averaged X-ray projection data of the intermittent two-phase flow. We measured the 3D void fraction distribution in a vertical square (5 × 5) rod array that simulated a BWR fuel assembly in the air-water test. From the 3D time-averaged CT images, we confirmed that the void fraction at the center part of the channel box was higher than that near the channel box wall, and the local void fraction at the central region of a subchannel was higher than that at the gap region of the subchannel. A comparison of the volume-averaged void fractions evaluated by the developed X-ray CT system with those evaluated by a differential pressure transducer in a void fraction range from 0.05 to 0.40 showed satisfactory agreement within a difference of 0.03.


Sign in / Sign up

Export Citation Format

Share Document