scholarly journals Aseptic Packaging – A Novel Technology to the Food Industry

2019 ◽  
Vol Volume-3 (Issue-3) ◽  
pp. 307-310
Author(s):  
Sanjana M. C. ◽  
Hemegowda R. ◽  
Sushma R. E. ◽  
Author(s):  
Alka Mishra ◽  
Subir Kumar Chakraborty ◽  
Manoj Kumar Tripathi

Aims: To reduce the microbial load on cut-carrot surface using 390 nm Light Emiting Diode ( LED) illumination Place and Duration of Study: Agro-Produce Processing Division, ICAR Central Institute of Agricultural Engineering, India between August, 2017 to November, 2019 Methodology: Samples were collected from local market from India and LED treatment was given to samples and microbial analysis was conducted using spread plate method. Results: The effect of 390 nm LEDs on cut-carrot surface has been evaluated in this study. The effect of dosage was found significant (p<0.05) for reducing bacterial and fungal load. Significant bacterial and fungal reduction was observed from 20 min of treatment till 3 h. Maximum inactivation of 28.4 % of bacteria and 24.1 % of fungus were detected at 3 h of exposure. These results demonstrated the potential of 390 nm LEDs as surface decontamination technology for cut-fruits and vegetables. Conclusion: 390 nm LED illumination can be a suitable and eco-friendly novel technology for surface decontamination of cut fruits and vegetables in the food industry.


Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 2148
Author(s):  
Carolina Rodrigues ◽  
Victor Gomes Lauriano Souza ◽  
Isabel Coelhoso ◽  
Ana Luísa Fernando

Intelligent food packaging is emerging as a novel technology, capable of monitoring the quality and safety of food during its shelf-life time. This technology makes use of indicators and sensors that are applied in the packaging and that detect changes in physiological variations of the foodstuffs (due to microbial and chemical degradation). These indicators usually provide information, e.g., on the degree of freshness of the product packed, through a color change, which is easily identified, either by the food distributor and the consumer. However, most of the indicators that are currently used are non-renewable and non-biodegradable synthetic materials. Because there is an imperative need to improve food packaging sustainability, choice of sensors should also reflect this requirement. Therefore, this work aims to revise the latest information on bio-based sensors, based on compounds obtained from natural extracts, that can, in association with biopolymers, act as intelligent or smart food packaging. Its application into several perishable foods is summarized. It is clear that bioactive extracts, e.g., anthocyanins, obtained from a variety of sources, including by-products of the food industry, present a substantial potential to act as bio-sensors. Yet, there are still some limitations that need to be surpassed before this technology reaches a mature commercial stage.


Author(s):  
Jean Fincher

An important trend in the food industry today is reduction in the amount of fat in manufactured foods. Often fat reduction is accomplished by replacing part of the natural fat with carbohydrates which serve to bind water and increase viscosity. It is in understanding the roles of these two major components of food, fats and carbohydrates, that freeze-fracture is so important. It is well known that conventional fixation procedures are inadequate for many food products, in particular, foods with carbohydrates as a predominant structural feature. For some food science applications the advantages of freeze-fracture preparation procedures include not only the avoidance of chemical fixatives, but also the opportunity to control the temperature of the sample just prior to rapid freezing.In conventional foods freeze-fracture has been used most successfully in analysis of milk and milk products. Milk gels depend on interactions between lipid droplets and proteins. Whipped emulsions, either whipped cream or ice cream, involve complex interactions between lipid, protein, air cell surfaces, and added emulsifiers.


2019 ◽  
Vol 13 (3) ◽  
pp. 5653-5664
Author(s):  
M. S. M. Al-Jethelah ◽  
H. S. Dheyab ◽  
S. Khudhayer ◽  
T. K. Ibrahim ◽  
A. T. Al-Sammarraie

Latent heat storage has shown a great potential in many engineering applications. The utilization of latent heat storage has been extended from small scales to large scales of thermal engineering applications. In food industry, latent heat has been applied in food storage. Another potential application of latent heat storage is to maintain hot beverages at a reasonable drinking temperature for longer periods. In the present work, a numerical calculation was performed to investigate the impact of utilizing encapsulated phase change material PCM on the temperature of hot beverage. The PCM was encapsulated in rings inside the cup. The results showed that the encapsulated PCM reduced the coffee temperature to an acceptable temperature in shorter time. In addition, the PCM maintained the hot beverage temperature at an acceptable drinking temperature for rational time.


1998 ◽  
Author(s):  
Peter A. Williams ◽  
Glyn O. Phillips
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document