scholarly journals Comparison of Probabilistically Evaluated COF with the Base Shear Distribution of IBC and Japanese Code

2011 ◽  
Vol 10 (1) ◽  
pp. 187-193
Author(s):  
Mohammad Sharfuddin ◽  
Hideki Idota
Keyword(s):  
Base Shear ◽  
Shear Distribution

3D design of steel structures with considering nonlinear base shear distribution and seismic energy

Structures ◽  
2022 ◽  
Vol 37 ◽  
pp. 82-94
Author(s):  
Masoud Ghamari ◽  
Mohammad Shooshtari ◽  
Hossein Homaei
Keyword(s):  
Steel Structures ◽  
Seismic Energy ◽  
Base Shear ◽  
3D Design ◽  
Shear Distribution

scholarly journals Comparison of Novel Seismic Protection Devices to Attenuate the Earthquake Induced Energy

Actuators ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 73
Author(s):  
Osman Hansu ◽  
Esra Mete Güneyisi
Keyword(s):  
Lateral Displacement ◽  
Time History ◽  
Seismic Protection ◽  
Base Shear ◽  
Seismic Demands ◽  
Nonlinear Time History Analyses ◽  
History Of ◽  
Protection Devices ◽  
Nonlinear Time History ◽  
Better Than

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as innovative seismic protection devices. For this purpose, 4-, 8- and 12-story steel bare frames were designed with 6.5 m equal span length and 4 m story height. Thereafter, they were seismically improved by mounting the VDs and BRBs in three patterns, namely outer bays, inner bays, and all bays over the frame heights. The structures were modeled using SAP 2000 software and evaluated by the nonlinear time history analyses subjected to the six natural ground motions. The seismic responses of the structures were investigated for the lateral displacement, interstory drift, absolute acceleration, maximum base shear, and time history of roof displacement. The results clearly indicated that the VDs and BRBs reduced seismic demands significantly compared to the bare frame. Moreover, the all-bay pattern performed better than the others.

Study on storey shear and base shear for irregular G+3, G+6 structures in seismic zones II and III erected on all three soils

2021 ◽  
Author(s):  
Vanadeep Cotipalli ◽  
T. Srinivas ◽  
Vegiraju Naresh Kumar Varma
Keyword(s):  
Base Shear ◽  
Seismic Zones

scholarly journals Effect of Bottom Geometry on the Natural Sloshing Motion of Water Inside Tanks: An Experimental Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 605
Author(s):  
Antonio Agresta ◽  
Nicola Cavalagli ◽  
Chiara Biscarini ◽  
Filippo Ubertini
Keyword(s):  
Energy Dissipation ◽  
Water Depth ◽  
Shear Force ◽  
Experimental Tests ◽  
Shear Load ◽  
Damping Properties ◽  
Base Shear ◽  
Structure Interaction ◽  
Sloshing Phenomenon ◽  
Key Aspects

The present work aims at understanding and modelling some key aspects of the sloshing phenomenon, related to the motion of water inside a container and its effects on the substructure. In particular, the attention is focused on the effects of bottom shapes (flat, sloped and circular) and water depth ratio on the natural sloshing frequencies and damping properties of the inner fluid. To this aim, a series of experimental tests has been carried out on tanks characterised by different bottom shapes installed over a sliding table equipped with a shear load cell for the measurement of the dynamic base shear force. The results are useful for optimising the geometric characteristics of the tank and the fluid mass in order to obtain enhanced energy dissipation performances by exploiting fluid–structure interaction effects.

scholarly journals Tuned Mass Damper Design for Slender Masonry Structures: A Framework for Linear and Nonlinear Analysis

2021 ◽  
Vol 11 (8) ◽  
pp. 3425
Author(s):  
Marco Zucca ◽  
Nicola Longarini ◽  
Marco Simoncelli ◽  
Aly Mousaad Aly
Keyword(s):  
Nonlinear Analysis ◽  
Linear Time ◽  
Design Procedure ◽  
Time History ◽  
Tuned Mass Damper ◽  
Second Phase ◽  
Masonry Structures ◽  
Base Shear ◽  
Mass Damper ◽  
Linear And Nonlinear

The paper presents a proposed framework to optimize the tuned mass damper (TMD) design, useful for seismic improvement of slender masonry structures. A historical masonry chimney located in northern Italy was considered to illustrate the proposed TMD design procedure and to evaluate the seismic performance of the system. The optimization process was subdivided into two fundamental phases. In the first phase, the main TMD parameters were defined starting from the dynamic behavior of the chimney by finite element modeling (FEM). A series of linear time-history analyses were carried out to point out the structural improvements in terms of top displacement, base shear, and bending moment. In the second phase, masonry's nonlinear behavior was considered, and a fiber model of the chimney was implemented. Pushover analyses were performed to obtain the capacity curve of the structure and to evaluate the performance of the TMD. The results of the linear and nonlinear analysis reveal the effectiveness of the proposed TMD design procedure for slender masonry structures.

The effect of element strength assignment on the torsional response of stiffness-eccentric systems

2013 ◽  
Vol 40 (7) ◽  
pp. 655-662
Author(s):  
George K. Georgoussis
Keyword(s):  
Structural Design ◽  
Shear Force ◽  
Ground Motions ◽  
Building Structures ◽  
Centre Of Mass ◽  
Base Shear ◽  
Structural Behaviour ◽  
Torsional Response ◽  
Building Models ◽  
Storey Building

Building structures of low or medium height are usually designed with a pseudostatic approach using a base shear much lower than that predicted from an elastic spectrum. Given this shear force, the objective of this paper is to evaluate the effect of the element strength assignment (as determined by several building codes) on the torsional response of inelastic single-storey eccentric structures and to provide guidelines for minimizing this structural behaviour. It is demonstrated that the expected torque about the centre of mass (CM) may be, with equal probability, positive (counterclockwise) or negative (clockwise). This result means that the torsional strength should also be provided in equal terms in both rotational directions, and therefore the base shear and torque (BST) surface of a given system must be symmetrical (or approximately symmetrical). In stiffness-eccentric systems, appropriate BST surfaces may be obtained when a structural design is based on a pair of design eccentricities in a symmetrical order about CM, and this is shown in representative single-storey building models under characteristic ground motions.

Sign in / Sign up

Export Citation Format

Share Document