INDUSTEEL MARS 380

Alloy Digest ◽  
2021 ◽  
Vol 70 (3) ◽  
Keyword(s):  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
Ballistic Protection

Abstract Industeel Mars 380 (earlier known as Industeel Mars 190) is a low-carbon, Ni-Cr-Mo-V-B, alloy protection steel that is used in the quenched and tempered condition (typical hardness = 380 HBW). It is used as rolled homogeneous armor for ballistic protection and evaluation of armor-defeating ammunition. This datasheet provides information on composition, hardness, and bend strength. It also includes information on forming, heat treating, machining, and joining. Filing Code: SA-869. Producer or source: Industeel France.

SANDVIK PRESSURFECT

Alloy Digest ◽  
2015 ◽  
Vol 64 (1) ◽  
Keyword(s):  
High Pressure ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Direct Injection ◽  
Heat Treating ◽  
Gasoline Direct Injection ◽  
Fuel System ◽  
Bend Strength ◽  
Low Carbon ◽  
Steel Company

Abstract Sandvik Pressurfect is an austenitic chromium-nickel stainless steel with low carbon content used for high-pressure gasoline direct injection (GDI) fuel system. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and bend strength. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: SS-1195. Producer or source: Sandvik Steel Company.

ISPAT INLAND MartINsite

Alloy Digest ◽  
2003 ◽  
Vol 52 (2) ◽  
Keyword(s):  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
High Carbon ◽  
Ultrahigh Strength Steel ◽  
Spring Steels ◽  
Alloy Steels ◽  
Cold Rolled ◽  
Nonferrous Alloys

Abstract Ispat Inland MartINsite is a low-carbon cold-rolled ultrahigh-strength steel available in four grades with minimum tensile strengths of 900 MPa (130 ksi) (M-130), 1100 MPa (160 ksi) (M-160), 1310 MPa (190 ksi) (M-190), and 1520 MPa (220 psi) (M-220). This steel can be used where high strength and/or lightweight are required and can substitute for high-carbon alloy steels, spring steels, and some nonferrous alloys at significant savings in cost. Electrosite is an electrogalvanized form of M-190. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and bend strength. It also includes information on wear resistance as well as heat treating and surface treatment. Filing Code: CS-62. Producer or source: Ispat Inland Inc. Originally published as Inland MartINsite, October 1976, revised February 2003.

NIROSTA 4461

Alloy Digest ◽  
2002 ◽  
Vol 51 (3) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Intergranular Corrosion ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
Austenitic Alloy ◽  
Intergranular Corrosion Resistance

Abstract NIROSTA 4461 is a low-carbon chromium-nickel austenitic alloy with molybdenum and titanium. It has good corrosion and intergranular corrosion resistance. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and bend strength. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-847. Producer or source: ThyssenKrupp Nirosta GmbH.

SSAB RAMOR 500

Alloy Digest ◽  
2021 ◽  
Vol 70 (8) ◽  
Keyword(s):  
Tensile Properties ◽  
Heat Treating ◽  
Bend Strength ◽  
Nickel Chromium ◽  
Ballistic Protection

Abstract SSAB Ramor 500 is a nickel-chromium-molybdenum-boron, alloy protection steel that is used in the quenched condition (hardness = 490–560 HBW) for ballistic protection. This datasheet provides information on composition, hardness, tensile properties, and bend strength. It also includes information on forming, heat treating, and joining. Filing Code: SA-875. Producer or source: SSAB AB.

BETHSTAR 50

Alloy Digest ◽  
2003 ◽  
Vol 52 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Physical Properties ◽  
Steel Plate ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
Low Sulfur ◽  
Minimum Yield

Abstract BethStar 50 steel plate is a high-strength product with a 345 MPa (50 ksi) minimum yield strength. It contains low carbon and low sulfur and has outstanding toughness, weldability, and formability. It provides options for off-highway equipment. This datasheet provides information on composition, physical properties, microstructure, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-520. Producer or source: Bethlehem Lukens Plate.

STRIMEK

Alloy Digest ◽  
1984 ◽  
Vol 33 (9) ◽  
Keyword(s):  
Hsla Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
Strip Steel ◽  
Reinforced Plastic ◽  
Low Weight ◽  
Microalloying Elements

Abstract STRIMEK is a Super High-Strength Low-Alloy (HSLA) steel. It is a microalloyed high-strength steel. Its unique properties are obtained in a carefully moniored process where microalloying elements are added and a special type of heat teatment is carried out. Strimek is lighter than an equivalent component of the same strength in low-carbon steel, aluminum or fibreglass-reinforced plastic. It is available in three grades, all of which have the unique combination of high strength, good formability and good weldability. Strimek is recommended where high strength at low weight is needed. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and bend strength. It also includes information on forming, heat treating, machining, and joining. Filing Code: SA-401. Producer or source: Uddeholm Strip Steel AB.

SSAB ARMOX 500T

Alloy Digest ◽  
2021 ◽  
Vol 70 (4) ◽  
Keyword(s):  
Tensile Properties ◽  
Heat Treating ◽  
Low Carbon ◽  
Nickel Chromium ◽  
Ballistic Protection

Abstract SSAB Armox 500T is a low-carbon, nickel-chromium-molybdenum-boron, alloy protection steel that is used in the quenched and tempered condition (typical hardness = 500 HBW) for ballistic protection. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on heat treating, machining, and joining. Filing Code: SA-870. Producer or source: SSAB AB.

B&W IRON

Alloy Digest ◽  
1968 ◽  
Vol 17 (8) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Physical Properties ◽  
Magnetic Permeability ◽  
Electric Motor ◽  
Low Carbon Steel ◽  
Heat Treating ◽  
Magnetic Characteristics ◽  
Low Carbon ◽  
High Magnetic Permeability

Abstract B and W IRON is a thoroughly killed, low carbon steel having a combination of ductility, toughness and high magnetic permeability. It is recommended for applications where good magnetic characteristics are of primary significance, such as in the manufacture of electric motor and generator housings. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Fe-35. Producer or source: Babcock & Wilcox Company.

WIELAND-K32

Alloy Digest ◽  
2005 ◽  
Vol 54 (1) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Electrical Engineering ◽  
Heat Treating ◽  
Power Cables ◽  
Bend Strength ◽  
Thermal Conductivities

Abstract Wieland-K32 is a nondeoxidized copper with acceptable electrical and thermal conductivities. It is often called electrolytic tough pitch copper. Typical applications include wrapping strip for power cables and for coaxial telephone cables in electrical engineering. This datasheet provides information on composition, physical properties, elasticity, and bend strength. It also includes information on corrosion resistance as well as heat treating and joining. Filing Code: CU-728. Producer or source: Wieland Metals Inc.

NICROFER 5923 HMo-ALLOY 59

Alloy Digest ◽  
1993 ◽  
Vol 42 (5) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Face Centered Cubic ◽  
Low Carbon ◽  
High Alloy ◽  
Temperature Performance ◽  
Cubic Structure ◽  
Face Centered

Abstract NICROFER 5923 hMo, often called Alloy 59, was developed with extra low carbon and silicon contents and with a high alloy level of molybdenum to optimize its corrosion resistance. Nicrofer 5923hMo has a face-centered cubic structure. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on high temperature performance as well as forming, heat treating, and joining. Filing Code: Ni-430. Producer or source: VDM Technologies Corporation.

Sign in / Sign up

Export Citation Format

Share Document