STRIMEK

Alloy Digest ◽  
1984 ◽  
Vol 33 (9) ◽  
Keyword(s):  
Hsla Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
Strip Steel ◽  
Reinforced Plastic ◽  
Low Weight ◽  
Microalloying Elements

Abstract STRIMEK is a Super High-Strength Low-Alloy (HSLA) steel. It is a microalloyed high-strength steel. Its unique properties are obtained in a carefully moniored process where microalloying elements are added and a special type of heat teatment is carried out. Strimek is lighter than an equivalent component of the same strength in low-carbon steel, aluminum or fibreglass-reinforced plastic. It is available in three grades, all of which have the unique combination of high strength, good formability and good weldability. Strimek is recommended where high strength at low weight is needed. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and bend strength. It also includes information on forming, heat treating, machining, and joining. Filing Code: SA-401. Producer or source: Uddeholm Strip Steel AB.

DOMEX 550MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (3) ◽  
Keyword(s):  
Physical Properties ◽  
Hsla Steel ◽  
Steel Structures ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Wide Range ◽  
Hot Rolled ◽  
Earthmoving Machines

Abstract Domex 550MC is a hot-rolled, high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-12.80 mm. The alloy meets or exceeds the requirements of S550MC in EN 10149-2. Applications include a wide range of fabricated components and steel structures, including truck chassis, crane booms, and earthmoving machines. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fatigue. It also includes information on forming, heat treating, and joining. Filing Code: SA-594. Producer or source: SSAB Swedish Steel Inc.

DOMEX 600MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (4) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Hsla Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Hot Rolled ◽  
Earthmoving Machines

Abstract Domex 600MC is a hot-rolled, extra high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-10.00 mm. The alloy meets or exceeds the requirements of S600MC in EN 10149-2. Applications include truck chassis, crane booms, and earthmoving machines. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-598. Producer or source: SSAB Swedish Steel Inc.

DOMEX 500MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Hsla Steel ◽  
Steel Structures ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Wide Range ◽  
Hot Rolled

Abstract Domex 500MC is a hot-rolled, high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-13.00 mm. The alloy meets or exceeds the requirements of S500MC in EN 10149-2. Applications include a wide range of fabricated components and steel structures, including truck chassis and crane booms. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-592. Producer or source: SSAB Swedish Steel Inc.

DOMEX 355MC

Alloy Digest ◽  
2008 ◽  
Vol 57 (10) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Hsla Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Hot Rolled

Abstract Domex 355 MC is a hot-rolled, high-strength low-alloy (HSLA) steel for cold forming operations. The alloy meets or exceeds the requirements of S355MC in EN 10149-2. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-585. Producer or source: SSAB Swedish Steel Inc.

scholarly journals Effect of Aluminum on Microstructure and Mechanical Properties of Weld Metal of Q960 Steel

Crystals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 26
Author(s):  
Zongxuan Zou ◽  
Zhengjun Liu ◽  
Xingyu Ai ◽  
Dan Wu
Keyword(s):  
Tensile Strength ◽  
Weld Metal ◽  
Impact Energy ◽  
Hsla Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Low Carbon ◽  
Cored Wire ◽  
Al Content ◽  
The Impact

High-strength low-alloy (HSLA) steel is used in important steel structural members because of its strength and plastic toughness. Q960 steel is HSLA steel obtained by adding an appropriate amount of alloy elements and quenching and tempering treatment on the basis of ordinary low-carbon steel. This kind of steel has strong hardenability due to the alloy elements added. Cold cracks, embrittlement and softening of the heat-affected zone easily occur after welding. In particular, the low-temperature impact toughness cannot meet the requirements and limits its use. In this paper, self-shielded welding is used to adjust the content of aluminum in flux-cored wire. The relationship between weld metal (WM) microstructure and strength and properties was studied by tensile test and impact test, and the influence mechanism of Al content on weld metal microstructure and properties was analyzed. The results show that when the content of Al is 0.21%, the impact energy at 0 °C~−60 °C is the best, the tensile strength can reach 1035 MPA and the number of pores is small. The size of inclusions in WM is mostly less than 1.0 μm Al2O3 spherical oxide. It can become the center of acicular ferrite (AF) and increase the nucleation probability. However, with the increase of Al content, large irregular AlN inclusions are produced, which reduces the tensile strength and impact energy of the welded joint.

ISPAT INLAND MartINsite

Alloy Digest ◽  
2003 ◽  
Vol 52 (2) ◽  
Keyword(s):  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Low Carbon ◽  
High Carbon ◽  
Ultrahigh Strength Steel ◽  
Spring Steels ◽  
Alloy Steels ◽  
Cold Rolled ◽  
Nonferrous Alloys

Abstract Ispat Inland MartINsite is a low-carbon cold-rolled ultrahigh-strength steel available in four grades with minimum tensile strengths of 900 MPa (130 ksi) (M-130), 1100 MPa (160 ksi) (M-160), 1310 MPa (190 ksi) (M-190), and 1520 MPa (220 psi) (M-220). This steel can be used where high strength and/or lightweight are required and can substitute for high-carbon alloy steels, spring steels, and some nonferrous alloys at significant savings in cost. Electrosite is an electrogalvanized form of M-190. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and bend strength. It also includes information on wear resistance as well as heat treating and surface treatment. Filing Code: CS-62. Producer or source: Ispat Inland Inc. Originally published as Inland MartINsite, October 1976, revised February 2003.

DOMEX 650MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Impact Energy ◽  
Low Temperatures ◽  
Hsla Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Minimum Yield

Abstract Domex 650MC is a high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-10.00 mm. The alloy has a minimum yield strength of 650 MPa. Domex 650 MC with designation D and E meet or exceed the demands for steel S650MC in EN-10149-2 for impact energy at low temperatures. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-599. Producer or source: SSAB Swedish Steel Inc. and SSAB Tunnplat AB.

DOMEX 315 MC

Alloy Digest ◽  
2008 ◽  
Vol 57 (7) ◽  
Keyword(s):  
Fracture Toughness ◽  
Hsla Steel ◽  
High Strength ◽  
Heat Treating ◽  
Grain Structure ◽  
Bend Strength ◽  
Cold Forming ◽  
Fine Grain ◽  
Thermomechanical Rolling ◽  
Hot Rolled

Abstract Domex 315 MC is a hot-rolled, high-strength low-alloy (HSLA) steel with a fine grain structure produced through thermomechanical rolling. It is used for cold-forming operations. The alloy meets or exceeds the requirements of S315MC in EN 10149-2. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-581. Producer or source: SSAB Swedish Steel Inc.

DOMEX 700MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (6) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Impact Energy ◽  
Low Temperatures ◽  
Hsla Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Minimum Yield

Abstract Domex 700MC is a high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-10.00 mm. The alloy has a minimum yield strength of 700 MPa. Domex 700 MC with designation D and E meet and exceed the demands for steel S700 MC in EN-10149-2 for impact energy at low temperatures. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-602. Producer or source: SSAB Swedish Steel Inc. and SSAB Tunnplat AB.

DOMEX 460 MC

Alloy Digest ◽  
2009 ◽  
Vol 58 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Hsla Steel ◽  
Steel Structures ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Cold Forming ◽  
Wide Range ◽  
Hot Rolled

Abstract Domex 460 MC is a hot-rolled, high-strength low-alloy (HSLA) steel for cold forming operations. It is available in thicknesses of 2.00-13.00 mm. The alloy meets or exceeds the requirements of S460MC in EN 10149-2. Applications include a wide range of fabricated components and steel structures. This datasheet provides information on composition, physical properties, tensile properties, and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-591. Producer or source: SSAB Swedish Steel Inc.

Sign in / Sign up

Export Citation Format

Share Document