UNS Z35840

Alloy Digest ◽  
1988 ◽  
Vol 37 (11) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Corrosion And Wear ◽  
Zinc Alloy ◽  
Thin Walled ◽  
Aluminum Copper Alloy ◽  
Lower Material

Abstract UNS No. Z35840 is a zinc-aluminum-copper alloy that offers exceptionally high strength (58,000 to 64,000 psi tensile strength as cast) at modest cost. It performs best in thin-walled castings (down to 0.10 inch) which means reduced weight and lower material costs when castings are redesigned. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as fracture toughness, creep, and fatigue. It also includes information on corrosion and wear resistance as well as forming, heat treating, machining, and surface treatment. Filing Code: Zn-44. Producer or source: Zinc alloy producers.

ZA-27

Alloy Digest ◽  
1977 ◽  
Vol 26 (10) ◽  
Keyword(s):  
Fracture Toughness ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
General Purpose ◽  
Corrosion And Wear ◽  
Heavy Section ◽  
Thin Walled ◽  
Aluminum Copper Alloy ◽  
Lower Material

Abstract ZA-27 is a zinc-aluminum-copper alloy that offers exceptionally high strength (58,000 to 64,000 psi tensile strength as cast) at modest cost. It performs best in thin-walled castings (down to 0.10 inch) which means reduced weight and lower material costs when castings are redesigned. It is similar to the general-purpose ZA-12 alloy (Alloy Digest Zn-31, September 1977) except for its higher strength and elongation, but with higher casting temperatures and poor heavy-section castability. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fracture toughness and creep. It also includes information on corrosion and wear resistance as well as casting, forming, heat treating, machining, and surface treatment. Filing Code: Zn-32. Producer or source: Eastern Alloys Inc.. See also Alloy Digest Zn-50, June 1990.

UNS Z35630

Alloy Digest ◽  
1988 ◽  
Vol 37 (7) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Shear Strength ◽  
High Strength ◽  
Heat Treating ◽  
General Purpose ◽  
Corrosion And Wear ◽  
Zinc Alloy ◽  
Aluminum Castings ◽  
Moderate Cost

Abstract UNS No. Z35630 is a zinc-aluminum-copper foundry alloy recommended for general-purpose castings of high strength at moderate cost. It was designed for use in nonferrous foundries to compete with cast-iron, bronze, brass and aluminum castings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as fracture toughness and fatigue. It also includes information on corrosion and wear resistance as well as casting, forming, heat treating, machining, and surface treatment. Filing Code: Zn-43. Producer or source: Zinc alloy producers.

BALL ROLLED ZINC ALLOY 809

Alloy Digest ◽  
1978 ◽  
Vol 27 (2) ◽  
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Zinc Alloy ◽  
Bend Strength ◽  
Chemical Division ◽  
Aluminum Copper Alloy

Abstract BALL ROLLED ZINC Alloy 809 is a zinc-aluminum-copper alloy that displays maximum strength, hardness and wear resistance among zinc-base alloys. Despite its high strength, it can be machined readily. It does not stain other metals and is used in such applications as keys and tokens. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear and bend strength It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Zn-33. Producer or source: Ball Corporation, Metal and Chemical Division.

ZA-12

Alloy Digest ◽  
1977 ◽  
Vol 26 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Shear Strength ◽  
Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
General Purpose ◽  
Corrosion And Wear ◽  
Aluminum Castings ◽  
Moderate Cost

Abstract ZA-12 is a zinc-aluminum-copper foundry alloy recommended for general-purpose castings of high strength at moderate cost. Its properties are similar to those of cast iron; however, it was designed for use in nonferrous foundries to compete with cast-iron, bronze, brass and aluminum castings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as fracture toughness and fatigue. It also includes information on corrosion and wear resistance as well as casting, forming, heat treating, machining, and surface treatment. Filing Code: Zn-31. Producer or source: Eastern Alloys Inc.. See also Alloy Digest Zn-49, May 1990.

WIELAND-K60

Alloy Digest ◽  
2018 ◽  
Vol 67 (8) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Wear Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Corrosion And Wear

Abstract Wieland K60 is an age hardenable copper alloy combining good electrical and thermal conductivity with high strength. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion and wear resistance as well as heat treating and machining. Filing Code: Cu-878. Producer or source: Wieland Metals Inc..

COPPER ALLOY No. 630

Alloy Digest ◽  
1967 ◽  
Vol 16 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Aluminum Bronze ◽  
Good Corrosion Resistance ◽  
Temperature Performance

Abstract COPPER ALLOY No. 630 is a heat treatable aluminum bronze combining wear resistance with high strength and good corrosion resistance. It is recommended for propellers, pump parts, and valves, gears, shafts and pickling equipment. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-176. Producer or source: Ampco Metal Inc..

ATLANTIC 13B ALLOY

Alloy Digest ◽  
1976 ◽  
Vol 25 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
High Strength ◽  
Heat Treating ◽  
Casting Alloy ◽  
Silicon Bronze ◽  
Thin Walled ◽  
Engineering Corporation ◽  
Bronze Casting

Abstract ATLANTIC 13B Alloy is a silicon bronze casting alloy offering excellent castability and corrosion resistance, good machinability and medium-high strength. It is an all-purpose alloy that is suitable for gears, valve parts and marine fittings. It is especially useful in stress-corrosion environments for thin-walled parts. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Cu-307. Producer or source: Atlantic Casting and Engineering Corporation.

COPPER ALLOY No. 220

Alloy Digest ◽  
1972 ◽  
Vol 21 (4) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Copper Alloy ◽  
Heat Treating ◽  
Zinc Alloy ◽  
Temperature Performance ◽  
Copper Zinc ◽  
Resistance To Stress

Abstract COPPER ALLOY No. 220, previously called Commercial Bronze, 90%, is a copper-zinc alloy having good formability and resistance to stress-corrosion cracking. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fracture toughness. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-254. Producer or source: Brass mills.

COPPER ALLOY No. 260

Alloy Digest ◽  
1971 ◽  
Vol 20 (9) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Zinc Alloy ◽  
Good Corrosion Resistance ◽  
Temperature Performance

Abstract COPPER ALLOY No. 260 is a 70% copper-30% zinc alloy having high strength, excellent ductility, and good corrosion resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as creep and fatigue. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-241. Producer or source: Brass mills.

AMPCOLOY 405

Alloy Digest ◽  
1962 ◽  
Vol 11 (4) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Corrosion And Wear ◽  
Wear Resistant

Abstract Ampcoloy 405 is a high strength, ductile, corrosion and wear resistant copper alloy available in extruded solid bar form for gears, valve seats, marine hardware, etc. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-116. Producer or source: Ampco Metal Inc..

Sign in / Sign up

Export Citation Format

Share Document