scholarly journals DEFORMATION AND STABILITY ANALYSIS OF SHALLOW THIN-WALLED CONICAL SHELLS IN CASE OF COMBINED LOAD OF UNIFORM PRESSURE AND CONCENTRATED IN POINT FORCE USING ANSYS SOFTWARE ENVIRONMENT

2020 ◽  
pp. 27-33
Author(s):  
Y.O. Bessmertnyi ◽  
◽  
V.L. Krasovsky ◽  
Keyword(s):  
Stability Analysis ◽  
Point Force ◽  
Uniform Pressure ◽  
Ansys Software ◽  
Software Environment ◽  
Conical Shells ◽  
Combined Load ◽  
Thin Walled

Upgraded Railway Front Searchlight Design Plastic Deformations by its Vibrations with Resonance Frequencies

2016 ◽  
Vol 684 ◽  
pp. 111-119 ◽  
Author(s):  
Stanislav Rafaelevich Abulkhanov ◽  
Dmitrii Sergeevich Goryainov
Keyword(s):  
Natural Frequencies ◽  
Ansys Software ◽  
Software Environment ◽  
Low Frequencies ◽  
Plastic Deformations ◽  
Vibration Resistance ◽  
First Case ◽  
Resonance Frequencies ◽  
The One ◽  
Electric Lamp

Natural frequencies of the four upgraded front searchlight designs were received in ANSYS software environment. In the first case serial front searchlight incandescent electric lamp was replaced by a LED group which was mounted on the one-piece cylinder backing. The second front searchlight design had the backing which was upgraded by a radial ribs and concentric rigidity ferrules. Analyze of the backing deformation character by vibrations with the natural frequencies established a number of design solutions which make it possible to raise front searchlight vibration resistance. By the front searchlight model were established that the natural frequencies of the searchlight with the one-piece backing appertain to the whole range of the train vibrations. Natural frequencies of the backing with perforation, rigidity ferrules, and radial ribs appertain to the low frequencies of the railway locomotive vibrations spectrum. On basis of devised methodology of analyze of the deformation and natural frequencies of the surface carrying a LED group the vibration-proof searchlight design was introduced and researched.

Modeling and accounting of strengthening zones of thin-walled steel profiles in ANSYS

2021 ◽  
pp. 44-51
Author(s):  
Natalya D. Korsun ◽  
◽  
Darya A. Prostakishina
Keyword(s):  
Axial Compression ◽  
Software Modeling ◽  
Ansys Software ◽  
Thin Walled

The article describes the process and reflects the results of modeling a steel thin-walled sigma profile operating under axial compression in the ANSYS software. Modeling is carried out taking into account the zones of hardening of steel along the profile section. The results are analyzed and compared with the results obtained in STARK.

Lobar Buckling of Thin-Walled Cylindrical and Truncated Conical Shells Under External Pressure

1974 ◽  
Vol 18 (04) ◽  
pp. 272-277
Author(s):  
C. T. F. Ross
Keyword(s):  
Finite Element ◽  
Circular Cylinder ◽  
Numerical Solutions ◽  
External Pressure ◽  
Element Solution ◽  
Conical Shells ◽  
Varying Thickness ◽  
Complex Boundary ◽  
Thin Walled ◽  
Unsymmetrical Loading

Numerical solutions have been produced for the asymmetric instability of thin-walled circular cylindrical and truncated conical shells under external pressure. The solutions for the circular cylinder have shown that the assumed buckling configurations of Nash [l]2 and Kaminsky [2] were quite reasonable for fixed ends. Comparison was also made of the finite-element solution of conical shells with other analyses. From these calculations, it was shown that the numerical solutions were superior to the analytical ones, as the former could be readily applied to vessels of varying thickness or those subjected to unsymmetrical loading or with complex boundary conditions.

Analytical and experimental stability analysis of AU4G1 thin-walled tubular workpieces in turning process

2020 ◽  
Vol 234 (6-7) ◽  
pp. 1007-1018 ◽  
Author(s):  
Zied Sahraoui ◽  
Kamel Mehdi ◽  
Moez Ben-Jaber
Keyword(s):  
Stability Analysis ◽  
Feed Rate ◽  
Experimental Studies ◽  
Rake Angle ◽  
Machining Process ◽  
Structural Damping ◽  
Turning Process ◽  
Process Stability ◽  
Thin Walled ◽  
The Stability

The development of the manufacturing-based industries is principally due to the improvement of various machining operations. Experimental studies are important in researches, and their results are also considered useful by the manufacturing industries with their aim to increase quality and productivity. Turning is one of the principal machining processes, and it has been studied since the 20th century in order to prevent machining problems. Chatter or self-excited vibrations represent an important problem and generate the most negative effects on the machined workpiece. To study this cutting process problem, various models were developed to predict stable and unstable cutting conditions. Stability analysis using lobes diagrams became useful to classify stable and unstable conditions. The purpose of this study is to analyze a turning process stability using an analytical model, with three degrees of freedoms, supported and validated with experimental tests results during roughing operations conducted on AU4G1 thin-walled tubular workpieces. The effects of the tubular workpiece thickness, the feed rate and the tool rake angle on the machining process stability will be presented. In addition, the effect of an additional structural damping, mounted inside the tubular workpiece, on the machining process stability will be also studied. It is found that the machining stability process is affected by the tubular workpiece thickness, the feed rate and the tool rake angle. The additional structural damping increases the stability of the machining process and reduces considerably the workpiece vibrations amplitudes. The experimental results highlight that the dynamic behavior of turning process is governed by large radial deformations of the thin-walled workpieces. The influence of this behavior on the stability of the machining process is assumed to be preponderant.

Sign in / Sign up

Export Citation Format

Share Document