scholarly journals Investigation into effects/Investigating the effects of titanium powder concentrations mixed in dielectric fluid on material machining removal and surface roughness of SKD61 steel after electrical discharge machining by reverse electrode polarity

2015 ◽  
Vol 18 (2) ◽  
pp. 43-51
Author(s):  
Long Tien Banh ◽  
Cuong Ngo ◽  
Phan Huu Nguyen
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Material Removal ◽  
Titanium Powder ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Electrode Polarity ◽  
Edm Process

Electrical discharge machining (EDM) has found widespread applications in tool , mold and aerospace industries. Therefore, enhancement of the quality of the EDM process has become a major research concern. In this paper, the effect of various titanium powder concentrations on the Material Removal Rate (MRR), tool wear rate (TWR), surface roughness (Ra) in powder mixed electrical discharge machining (PMEDM) have been studied. The workpiece is SKD61steel and electrode made from copper with reverse polarity were used in experimental study. The results showed that titanium powder mixed into the dielectric fluid of EDM can enhance MRR without increasing TWR and Ra.

Surfactant and graphite powder–assisted electrical discharge machining of titanium alloy

2016 ◽  
Vol 231 (4) ◽  
pp. 641-657 ◽  
Author(s):  
Murahari Kolli ◽  
Adepu Kumar
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Recast Layer ◽  
Dielectric Fluid ◽  
Recast Layer Thickness

Surfactant and graphite powder–assisted electrical discharge machining was proposed and experiments were performed on titanium alloy in this investigation. Analysis was carried out to observe changes in dielectric fluid behaviour, material removal rate, surface roughness, recast layer thickness, surface topography and energy-dispersive X-ray spectroscopy. It was found out that the addition of surfactant to dielectric fluid (electrical discharge machining oil + graphite powder) improved the material removal rate and surface roughness. It was noticed to have reduced the recast layer thickness and agglomeration of graphite and sediment particles. Biface material migrations between the electrode and the workpiece surface were identified, and migration behaviour was powerfully inhibited by the mixing of surfactant. Surfactant added into dielectric fluid played an important role in the discharge gap, which increased the conductivity, and suspended debris particles in dielectric fluid reduced the abnormal discharge conditions of the machine and improved the overall machining efficiency.

A Study on Influence of Input Parameters on Surface Roughness in PMEDM Cylindrical Shaped Parts

2021 ◽  
Vol 1018 ◽  
pp. 65-70
Author(s):  
Tran Thi Hong ◽  
Bui Thanh Danh ◽  
Nguyen Van Cuong ◽  
Le Hong Ky ◽  
Nguyen Hong Linh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dielectric Fluid ◽  
Carbide Powder ◽  
Improve Quality ◽  
Input Parameters ◽  
Edm Process ◽  
Optimum Input

In electrical discharge machining (EDM) powder material can be mixed into the dielectric fluid to improve quality of machining surface of components. Therefore, finding suitable input parameters of this process becomes an important task. This paper presents a methodology to find the optimum input factors of the EDM process when adding nanosilicon carbide powder into the dielectric fluid for processing cylindrical shaped parts. In this research, the Taguchi method was used for experiment design in order to investigate the effect of the input parameters on the surface roughness. Also, optimum input factors for minimum surface roughness (RS) was proposed. The result from the deviation of SRbetween the analysis and the experiment demonstrates that the optimum input parameters are helpful to predict the value of surface roughness. Therefore, this can increase the economic and technical effectiveness in EDM process.

Parametric Optimization of PMEDM Process with Chromium Powder Suspended Dielectric for Minimum Surface Roughness and Maximum MRR

2011 ◽  
Vol 383-390 ◽  
pp. 3202-3206 ◽  
Author(s):  
Rajiv Kumar Garg ◽  
Kuldeep Ojha
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Material Removal ◽  
Parametric Optimization ◽  
Nickel Powder ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Chromium Powder ◽  
Average Current

In this article, parametric optimization for material removal rate (MRR) and surface roughness (SR) study on the powder mixed electrical discharge machining (PMEDM) of EN-8 steel has been carried out. Response surface methodology (RSM) has been used to plan and analyze the experiments. Average current, duty cycle, diameter of electrode and concentration of micro-nickel powder added into dielectric fluid of EDM were chosen as process parameters to study the PMEDM performance in terms of MRR and SR. Experiments have been performed on newly designed experimental setup developed in laboratory. Most important parameters affecting selected performance measures have been identified and effects of their variations have been observed.

Study on Finishing Cut with Dry WEDM

2006 ◽  
Vol 532-533 ◽  
pp. 273-276 ◽  
Author(s):  
Tong Wang ◽  
Xin Fu Zhang ◽  
Xue Fang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Lower Surface ◽  
Wire Electrical Discharge Machining ◽  
Dry Wedm

Utilizing gas as the dielectric instead of dielectric liquid has enabled the development of dry wire electrical discharge machining (WEDM) technology for finishing cut. This paper studies on the surface quality of tool steel with WEDM method, which is conducted in gas to improve the accuracy of finishing cut, and compares the surface quality in atmosphere and in water. Experiment results showed that Low-Speed WEDM in atmosphere offers advantages such as better straightness, lower surface roughness and shorter gap length, but WEDM in atmosphere has poorer material removal rate than conventional WEDM in water. It was also found the removal rate in atmosphere can be improved by increasing the wire winding speed.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Investigation of the Spark Cycle Effect on Material Removal Rate in Wire Electrical Discharge Machining

Manufacturing ◽  
2003 ◽  
Author(s):  
Scott F. Miller ◽  
Albert J. Shih
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Short Circuit ◽  
Wire Electrical Discharge Machining ◽  
Time Duration ◽  
Edm Process

The development of new, advanced engineering materials and the needs for precise and flexible prototype and low-volume production have made wire electrical discharge machining (EDM) an important manufacturing process to meet such demand. This research investigates the effect of spark on-time duration and spark on-time ratio, two important EDM process parameters, on the material removal rate (MRR) and surface integrity of four types of advanced material: porous metal foams, metal bond diamond grinding wheels, sintered Nd-Fe-B magnets, and carbon-carbon bipolar plates. An experimental procedure was developed. During the wire EDM, five types of constraints on the MRR due to short circuit, wire breakage, machine slide speed limit, and spark on-time upper and lower limits have been identified. An envelope of feasible EDM process parameters is created and compared across different work-materials. Applications of such process envelope to select process parameters for maximum MRR and for machining of micro features are presented.

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Analysis of MRR and TWR on OHNS Die Steel with Different Electrodes Using Electrical Discharge Machining

2016 ◽  
Vol 22 ◽  
pp. 112-120 ◽  
Author(s):  
S. Nallusamy
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Work Piece ◽  
Tool Wear Rate

Electrical Discharge Machining is a machining method primarily used for hard metals or those that are impossible to be machined with traditional techniques. The experimental investigation of material removal rate and tool wear rate during machining of oil hardened non-shrinking steel with brass and copper electrodes using EDM machine was carried out in this paper. This investigation presents the analysis and evaluation of heat affected zones and surface finish of the work piece using different tool electrodes and varying the machine parameters. The commercial grade kerosene oil has been used as dielectric fluid. The effect of various important EDM parameters such as discharge current (Ip) 2 to12A, pulse duration (Ton and Toff) and sparking voltage (V) of 80±5% have been used to yield the response in terms of Material Removal Rate (MRR) and Tool Wear Rate (TWR). Further a detailed analysis of the heat affected regions was also been carried out by using scanning electron microscopy.

Sign in / Sign up

Export Citation Format

Share Document