scholarly journals Improving the Conversion of Biomass in Catalytic Pyrolysis via Intensification of Biomass—Catalyst Contact by Co-Pressing

Catalysts ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 805
Author(s):  
Ishaka Muhammad ◽  
George Manos

Biomass pyrolysis is a promising technology for fuel and chemical production from an abundant renewable source. It takes place usually in two stages; non-catalytic pyrolysis with further catalytic upgrading of the formed pyrolysis oil. The direct catalytic pyrolysis of biomass reduces the pyrolysis temperature, increase the yield to target products and improves their quality. However, in such one-stage process the contact between biomass and solid catalyst particles is poor leading to an excessively high degree of pure thermal pyrolysis reactions. The aim of this study was to enhance the catalyst-biomass contact via co-pressing of biomass and catalyst particles as a pre-treatment method. Catalytic pyrolysis of biomass components with HY and USY zeolites was studied using thermogravimetric analysis (TGA), as well as experiments in a pyrolysis reactor. The liquid and coke yields were characterized using gas chromatography, and TGA respectively. The TGA results showed that the degradation of the co-pressed cellulose occurred at lower temperatures compared to the pure thermal degradation, as well as catalytic degradation of non-pretreated cellulose. All biomass components produced better results using the co-pressing method, where the liquid yields increased while coke/char yields decreased. Bio-oil from catalytic pyrolysis of cellulose with HY catalyst mainly produced heavier fractions, while in the presence of USY catalyst medium fraction was mainly produced within the gasoline range. For hemicellulose catalytic pyrolysis, the catalysts had similar effects in enhancing the lighter fraction, but specifically, HY showed higher selectivity to middle fraction while USY has produced higher percentage of lighter fraction. Using with both catalysts, co-pressing had the best effect of eliminating the heavier fraction and improving the gasoline range fraction. Spent catalyst from co-pressed sample had lower concentrations of coke/char components due to the shorter residence times of volatiles, which suppresses the occurrence of secondary reactions leading to coke/char formations.

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Sensho Honma ◽  
Toshimitsu Hata ◽  
Takashi Watanabe

The influence of catalysts on the compositions of char and pyrolysis oil obtained by pyrolysis of wood biomass with pulse current heating was studied. The effects of catalysts on product compositions were analyzed using GC-MS and TEM. The compositions of some aromatic compounds changed noticeably when using a metal oxide species as the catalyst. The coexistence or dissolution of amorphous carbon and iron oxide was observed in char pyrolyzed at 800°C with Fe3O4. Pyrolysis oil compositions changed remarkably when formed in the presence of a catalyst compared to that obtained from the uncatalyzed pyrolysis of wood meal. We observed a tendency toward an increase in the ratio of polyaromatic hydrocarbons in the pyrolysis oil composition after catalytic pyrolysis at 800°C. Pyrolysis of biomass using pulse current heating and an adequate amount of catalyst is expected to yield a higher content of specific polyaromatic compounds.


2013 ◽  
Vol 204 ◽  
pp. 170-178 ◽  
Author(s):  
Mi-Jin Jeon ◽  
Jong-Ki Jeon ◽  
Dong Jin Suh ◽  
Sung Hoon Park ◽  
Young Jin Sa ◽  
...  

Author(s):  
E Y. Wang ◽  
J. T. Cherian ◽  
A. Madsen ◽  
R. M. Fisher

Many steel parts are electro-plated with chromium to protect them against corrosion and to improve their wear-resistance. Good adhesion of the chrome plate to the steel surface, which is essential for long term durability of the part, is extremely dependent on surface preparation prior to plating. Recently, McDonnell Douglas developed a new pre-treatment method for chrome plating in which the steel is anodically etched in a sulfuric acid and hydrofluoric acid solution. On carbon steel surfaces, this anodic pre-treatment produces a dark, loosely adhering material that is commonly called the “smut” layer. On stainless steels and nickel alloys, the surface is only darkened by the anodic pre-treatment and little residue is produced. Anodic pre-treatment prior to hard chrome plating results in much better adherence to both carbon and alloy steels.We have characterized the anodic pre-treated steel surface and the resulting “smut” layer using various techniques including electron spectroscopy for chemical analysis (ESCA) on bulk samples and transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS) on stripped films.


2021 ◽  
Vol 121 ◽  
pp. 255-264
Author(s):  
Honggang Fan ◽  
Jing Gu ◽  
Yazhuo Wang ◽  
Haoran Yuan ◽  
Yong Chen ◽  
...  

BioResources ◽  
2015 ◽  
Vol 10 (3) ◽  
Author(s):  
Ze Wang ◽  
Siwei Liu ◽  
Weigang Lin ◽  
Wenli Song

Sign in / Sign up

Export Citation Format

Share Document