scholarly journals Column Separation of Am(III) and Eu(III) by α-Zirconium Phosphate Ion Exchanger in Nitric Acid

2020 ◽  
Vol 4 (1) ◽  
pp. 14
Author(s):  
Elmo W. Wiikinkoski ◽  
Iiro Rautsola ◽  
Junhua Xu ◽  
Risto Koivula

The trivalent lanthanide-actinide separations are a major challenge in reprocessing of nuclear fuels. To achieve this, commonly organic extractants and solvents are utilized in elaborate processes. Here we report a simple new method that can perform a supportive or alternative role. A nanocrystalline α-zirconium phosphate ion exchanger was utilized for Eu(III)/Am(III) column separation. Comprehensive preliminary studies were done using batch experiments to optimize the final separation conditions. The distribution coefficients for Eu were determined as a function of pH (from 0 to 3) and salinity (Na, Sr). The distribution coefficients for Am were determined as a function of pH, and Eu concentration, from 1:40 to 10,000:1 Eu:Am molar ratio. The exchanger always preferred Eu over Am in our experimental conditions. Separation factors (Eu:Am) of up to 400 were achieved in binary Eu-Am solution in pH 1. The breakthrough capacity was determined in dynamic column conditions using Eu: 0.3 meq∙g−1, which is approximately 4% of the theoretical maximum capacity. Two types of hot column separation tests were conducted: (i) binary load (selective Am elution), and (ii) continuous equimolar binary feed. In both cases separation was achieved. In (i), the majority (82% of the recovered 93%) of Am could be purified from Eu with extremely high 99.999% molar purity, while alternatively even more (95% of the recovered 93%) at a lower purity of 99.7 mol %. In (ii), up to 330 L∙kg−1 of the equimolar solution per mass of the exchanger could be treated with Am purity above 99.5 mol % in the total eluate. Alternatively, up to 630 L∙kg−1 above 95 mol %, or up to 800 L∙kg−1 above 90 mol % purities.

2004 ◽  
Vol 69 (8-9) ◽  
pp. 683-688 ◽  
Author(s):  
Jurij Vucina ◽  
Dagoljub Lukic ◽  
Milovan Stoiljkovic

The conditions for the efficient separation of tungsten(VI) and rhenium (VII) on alumina were established. The distribution coefficients K d for tungstate and perrhenate anions, as well as the separation factors ?(? = KdWO42-/Kd ReO4-) were determined using hydrochloric or nitric acid as the aqueous media. Asolution of sodium chloride in the pH range 2?6 was also examined. Under all the tested experimental conditions, alumina is a much better adsorbent for tungsten than for rhenium. The obtained results indicated that the best separation of these two elements is achieved when 0.01? 0.1 mol dm-3HCl or 1.0mol dm-3 HNO3 are used as the aqueous media. If NaCl is used as the aqueous phase, the best separation is achieved with 0.20 mol dm-3 NaCl pH 4?6. Under these experimental conditions, the breakthrough and saturation capacities of alumina for tungsten at pH4 are 17 and 26 mg W/g Al2O3 respectively. With increasing pH, these values decrease. Thus, at pH 6 they are only 4 and 13 mg W/g Al2O3, respectively.


2021 ◽  
Vol 11 (12) ◽  
pp. 5534
Author(s):  
Asmaa M. Abu El-Soad ◽  
Giuseppe Lazzara ◽  
Alexander V. Pestov ◽  
Daria P. Tambasova ◽  
Denis O. Antonov ◽  
...  

Modified halloysite nanotubes (HNTs-Cl) were synthesized by a coupling reaction with (3-chloropropyl) trimethoxysilane (CPTMS). The incorporation of chloro-silane onto HNTs surface creates HNTs-Cl, which has great chemical activity and is considered a good candidate as an active site that reacts with other active molecules in order to create new materials with great applications in chemical engineering and nanotechnology. The value of this work lies in the fact that improving the degree of grafting of chloro-silane onto the HNT’s surface has been accomplished by incorporation of HNTs with CPTMS under different experimental conditions. Many parameters, such as the dispersing media, the molar ratio of HNTs/CPTMS/H2O, refluxing time, and the type of catalyst were studied. The greatest degree of grafting was accomplished by using toluene as a medium for the grafting process, with a molar ratio of HNTs/CPTMS/H2O of 1:1:3, and a refluxing time of 4 h. The addition of 7.169 mmol of triethylamine (Et3N) and 25.97 mmol of ammonium hydroxide (NH4OH) led to an increase in the degree of grafting of CPTMS onto the HNT’s surface.


Catalysts ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 855
Author(s):  
Ahmed Amine Azzaz ◽  
Salah Jellali ◽  
Nasser Ben Harharah Hamed ◽  
Atef El Jery ◽  
Lotfi Khezami ◽  
...  

In the present study, methylene blue (MB) removal from aqueous solutions via the photocatalytic process using TiO2 as a catalyst in the presence of external ultra-violet light (UV) was investigated. The results of adsorption in the absence of UV radiation showed that adsorption reached an equilibrium state at 60 min. The experimental kinetic data were found to be well fitted by the pseudo-second-order model. Furthermore, the isotherm study suggested that dye uptake by TiO2 is a chemisorption process with a maximum retention capacity of 34.0 mg/g. The photodegradation of MB was then assessed under various experimental conditions. The related data showed that dye mineralization decreased when dye concentrations were increased and was favored at high pH values and low salt concentrations. The simultaneous presence of organic and inorganic pollution (Zinc) was also evaluated. The effect of the molar ratio Zn2+/MB+ in the solution at different pH values and NaCl concentrations was also monitored. The corresponding experimental results showed that at low values of Zn2+ in the solution (30 mg/L), the kinetic of the MB removal became faster until reaching an optimum at Zn2+/MB+ concentrations of 60/60 mg/L; it then slowed down for higher concentrations. The solutions’ carbon contents were measured during the degradation process and showed total mineralization after about 5 h for the optimal Zn2+/MB+ condition.


Sign in / Sign up

Export Citation Format

Share Document