scholarly journals Accuracy of 3D Landscape Reconstruction without Ground Control Points Using Different UAS Platforms

Drones ◽  
2020 ◽  
Vol 4 (2) ◽  
pp. 13 ◽  
Author(s):  
Margaret Kalacska ◽  
Oliver Lucanus ◽  
J. Pablo Arroyo-Mora ◽  
Étienne Laliberté ◽  
Kathryn Elmer ◽  
...  
Keyword(s):  
Low Cost ◽  
Ground Control ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Model Errors ◽  
Positional Accuracy ◽  
Ground Control Points ◽  
Digital Elevation ◽  
High Level ◽  
Aerial Systems

The rapid increase of low-cost consumer-grade to enterprise-level unmanned aerial systems (UASs) has resulted in the exponential use of these systems in many applications. Structure from motion with multiview stereo (SfM-MVS) photogrammetry is now the baseline for the development of orthoimages and 3D surfaces (e.g., digital elevation models). The horizontal and vertical positional accuracies (x, y and z) of these products in general, rely heavily on the use of ground control points (GCPs). However, for many applications, the use of GCPs is not possible. Here we tested 14 UASs to assess the positional and within-model accuracy of SfM-MVS reconstructions of low-relief landscapes without GCPs ranging from consumer to enterprise-grade vertical takeoff and landing (VTOL) platforms. We found that high positional accuracy is not necessarily related to the platform cost or grade, rather the most important aspect is the use of post-processing kinetic (PPK) or real-time kinetic (RTK) solutions for geotagging the photographs. SfM-MVS products generated from UAS with onboard geotagging, regardless of grade, results in greater positional accuracies and lower within-model errors. We conclude that where repeatability and adherence to a high level of accuracy are needed, only RTK and PPK systems should be used without GCPs.

scholarly journals Assessing the Accuracy of Digital Surface Models Derived from Optical Imagery Acquired with Unmanned Aerial Systems

Drones ◽  
2019 ◽  
Vol 3 (1) ◽  
pp. 15 ◽  
Author(s):  
Salvatore Manfreda ◽  
Petr Dvorak ◽  
Jana Mullerova ◽  
Sorin Herban ◽  
Pietro Vuono ◽  
...  
Keyword(s):  
3D Model ◽  
Low Cost ◽  
Three Dimensional ◽  
Careful Consideration ◽  
Ground Control ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Earthen Dam ◽  
Ground Control Points ◽  
Aerial Systems

Small unmanned aerial systems (UASs) equipped with an optical camera are a cost-effective strategy for topographic surveys. These low-cost UASs can provide useful information for three-dimensional (3D) reconstruction even if they are equipped with a low-quality navigation system. To ensure the production of high-quality topographic models, careful consideration of the flight mode and proper distribution of ground control points are required. To this end, a commercial UAS was adopted to monitor a small earthen dam using different combinations of flight configurations and by adopting a variable number of ground control points (GCPs). The results highlight that optimization of both the choice and combination of flight plans can reduce the relative error of the 3D model to within two meters without the need to include GCPs. However, the use of GCPs greatly improved the quality of the topographic survey, reducing error to the order of a few centimeters. The combined use of images extracted from two flights, one with a camera mounted at nadir and the second with a 20° angle, was found to be beneficial for increasing the overall accuracy of the 3D model and especially the vertical precision.

Application of Postprocessing Kinematic Methods with UAS Remote Sensing in Forest Ecosystems

2021 ◽  
Author(s):  
Zachary M Miller ◽  
Joseph Hupy ◽  
Aishwarya Chandrasekaran ◽  
Guofan Shao ◽  
Songlin Fei
Keyword(s):  
Remote Sensing ◽  
Data Collection ◽  
Ground Control ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Gps Technology ◽  
Ground Control Points ◽  
Forested Areas ◽  
Rapid Deployment ◽  
Aerial Systems

Abstract Unmanned Aerial Systems (UAS) serve as an excellent remote-sensing platform to fulfill an aerial imagery data collection niche previously unattainable in forestry by satellites and manned aircraft. However, for UAS-derived data to be spatially representative, a precise network of ground control points (GCP) is often required, which can be tedious and limit the logistical benefits of UAS rapid deployment capabilities, especially in densely forested areas. Therefore, methods for efficient data collection without GCPs are highly desired in UAS remote sensing. Here, we demonstrate the use of postprocessing kinematic (PPK) technology to obtain subcentimeter precision in datasets of forested areas without the need for placing GCPs. We evaluated two key measures, positional variability and time efficiency, of the PPK technology by comparing them to traditional GCP methods. Results show that PPK displays consistently higher positional precision than traditional GCP approaches. Moreover, PPK surveys and processing take less time to complete than traditional GCP methods and require fewer logistical steps, especially in image acquisition. The time and resource savings with PPK as compared to GCP processing are undeniable. We conclude that PPK technology provides a practical means to produce precise aerial forest surveys. Study Implications Unmanned Aerial Systems (UAS) have enormous potential for lowering costs and streamlining practices in the forestry management and research community. Despite this potential, however, UAS forestry applications have been limited in scope and precision because of a reliance on using ground-based GPS technology to survey ground control points (GCP), which are time intensive and require an open view of the sky. Such a need for a ground-based GCP survey, along with forest canopy serving to limit and scatter incoming GPS signals, diminishes the potential for rapid deployment and precision mapping offered by UAS. Fortunately, Postprocessing-Kinematic (PPK) GPS technology lowers these barriers by providing the means to seamlessly gather highly precise UAS imagery without needing to conduct time-intensive ground-based surveys. This study compares the precision and time-effectiveness between traditional GCP marker surveys and PPK correction methods.

scholarly journals THE INFLUENCE OF GROUND CONTROL POINTS CONFIGURATION AND CAMERA CALIBRATION FOR DTM AND ORTHOMOSAIC GENERATION USING IMAGERY OBTAINED FROM A LOW-COST UAV

2020 ◽  
Vol V-1-2020 ◽  
pp. 239-244
Author(s):  
M. V. Y. Garcia ◽  
H. C. Oliveira
Keyword(s):  
Low Cost ◽  
Digital Terrain Model ◽  
Flying Height ◽  
Ground Control ◽  
Optimum Number ◽  
Control Points ◽  
Digital Products ◽  
Positional Accuracy ◽  
Terrain Model ◽  
Ground Control Points

Abstract. Technological improvement of Unmanned Aerial Vehicles (UAVs) and computer vision algorithms, such as Structured-from-Motion (SfM) and Multi-view Stereo (MVS) have provided the possibility for high-resolution mapping and high-density point cloud generation using low-cost equipment and sensors. Orthomosaics and Digital Terrain Model (DTM) are the main digital products considering mapping purposes. Their quality is directly related to the sensors boarded on the UAV and data processing. Ground Control Points (GCPs) are used in the process of indirect georeferencing and also to model the lens distortions. The number of GCPs used in this process affects the positional accuracy of the final products. This study aims to determine the optimum number of GCPs to achieve high accuracy orthomosaics and DTM. To obtain this optimum number, an area of 3.85 ha was mapped with a low-cost UAV DJI Phantom 4 Advanced at 31 m flying height, lateral and longitudinal overlap of 90% and 80%, respectively, and using 22 checkpoints for quality assessment. For the experiments, different configuration were used both for the number of GCPs and for the use of self-calibration process or pre-calibrated camera IOP (Interior Orientation Parameters). The results show that for the flight configuration used in this work and for the mentioned UAV, a total of 5 GCPs, with pre-calibrated camera IOP, yields an accuracy of 0.023 m for X, 0.031 m for Y and 0.033 m for Z.

scholarly journals LOW-COST UAS PHOTOGRAMMETRY FOR ROAD INFRASTRUCTURES’ INSPECTION

2020 ◽  
Vol XLIII-B2-2020 ◽  
pp. 1145-1150
Author(s):  
L. Pinto ◽  
F. Bianchini ◽  
V. Nova ◽  
D. Passoni
Keyword(s):  
Low Cost ◽  
Laser Scanner ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
The Past ◽  
Ground Control Points ◽  
General Rules ◽  
Aerial Systems ◽  
Cloud Of Points ◽  
Non Destructive

Abstract. All over the world, road infrastructures are getting closer to their life cycle and need to be constantly inspected: a consistent number of bridges are structurally deficient, and the risk of collapse can no longer be excluded. In contrast with the past, the interest in structure durability has recently grown rapidly. In order to make bridges durable, it is necessary to carry out ordinary maintenance, preceded by inspection activities, which can be traditionally divided in two categories: destructive and non-destructive (NDT). All the NDT inspections (visual, IR thermography, GPR) can be conducted by using UAS (Unmanned Aerial Systems), a technology that makes bridges inspections quicker, cheaper, objective and repeatable. This study presents the visual inspection and survey of two bridges by using a UAS DJI Mavic 2 Pro, equipped with a 20Mpixel Hasselblad camera that records 60fps 4K video and a 10bit radiometric resolution. Starting from the acquired data, a 3D model of each structure was built by using Structure from Motion (SfM) principles and software. To validate the two models, each of them characterized by a centimetric accuracy, the UAS camera generated cloud of points and was co-registered with the point cloud of a terrestrial laser-scanner using Ground Control Points (GCPs). To make this, CloudCompare comparison software was used; the plugin M3C2 automatically calculates the distance between the points of two compared clouds. Finally, some general rules concerning the UAS main characteristics for inspection of bridges and software for data processing are proposed.

Detecting Geo-Positional Bias in Imagery Collected Using Small UASs

2021 ◽  
Vol 87 (9) ◽  
pp. 631-638
Author(s):  
Jonathan B. Thayn ◽  
Aaron M. Paque ◽  
Megan C. Maher
Keyword(s):  
Global Positioning System ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Positional Accuracy ◽  
Directional Bias ◽  
Unequal Variances ◽  
Ground Control Points ◽  
Positional Bias ◽  
Global Positioning ◽  
Aerial Systems

Statistical methods for detecting bias in global positioning system (<small>GPS</small>) error are presented and applied to imagery collected using three common unmanned aerial systems (<small>UASs</small>). Imagery processed without ground control points (<small>GCPs</small>) had horizontal errors of 1.0–2.5 m; however, the errors had unequal variances, significant directional bias, and did not conform to the expected statistical distribution and so should be considered unreliable. When <small>GCPs</small>were used, horizontal errors decreased to less than 5 cm, and the errors had equal variances, directional uniformity, and they conformed to the expected distribution. The analysis identified a longitudinal bias in some of the reference data, which were subsequently excluded from the analysis. Had these data been retained, the estimates of positional accuracy would have been unreliable and inaccurate. These results strongly suggest that examining <small>GPS</small> data for bias should be a much more common practice.

scholarly journals Determining the Suitable Number of Ground Control Points for UAS Images Georeferencing by Varying Number and Spatial Distribution

2020 ◽  
Vol 12 (5) ◽  
pp. 876 ◽  
Author(s):  
Valeria-Ersilia Oniga ◽  
Ana-Ioana Breaban ◽  
Norbert Pfeifer ◽  
Constantin Chirila
Keyword(s):  
Coordinate System ◽  
High Precision ◽  
Random Distribution ◽  
Low Cost ◽  
Local Coordinate System ◽  
Point Clouds ◽  
Ground Control ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Ground Control Points

Currently, products that are obtained by Unmanned Aerial Systems (UAS) image processing based on structure-from-motion photogrammetry (SfM) are being investigated for use in high precision projects. Independent of the georeferencing process being done directly or indirectly, Ground Control Points (GCPs) are needed to increase the accuracy of the obtained products. A minimum of three GCPs is required to bring the results into a desired coordinate system through the indirect georeferencing process, but it is well known that increasing the number of GCPs will lead to a higher accuracy of the final results. The aim of this study is to find the suitable number of GCPs to derive high precision results and what is the effect of GCPs systematic or stratified random distribution on the accuracy of the georeferencing process and the final products, respectively. The case study involves an urban area of about 1 ha that was photographed with a low-cost UAS, namely, the DJI Phantom 3 Standard, at 28 m above ground. The camera was oriented in a nadiral position and 300 points were measured using a total station in a local coordinate system. The UAS images were processed using the 3DF Zephyr software performing a full BBA with a variable number of GCPs i.e., from four up to 150, while the number and the spatial location of check points (ChPs) was kept constant i.e., 150 for each independent distribution. In addition, the systematic and stratified random distribution of GCPs and ChPs spatial positions was analysed. Furthermore, the point clouds and the mesh surfaces that were automatically derived were compared with a terrestrial laser scanner (TLS) point cloud while also considering three test areas: two inside the area defined by GCPs and one outside the area. The results expressed a clear overview of the number of GCPs needed for the indirect georeferencing process with minimum influence on the final results. The RMSE can be reduced down to 50% when switching from four to 20 GCPs, whereas a higher number of GCPs only slightly improves the results.

scholarly journals Accuracy Assessment on Unmanned Aerial System Derived Digital Surface Models

2018 ◽  
Author(s):  
Salvatore Manfreda ◽  
Petr Dvorak ◽  
Jana Mullerova ◽  
Sorin Herban ◽  
Pietro Vuono ◽  
...  
Keyword(s):  
3D Model ◽  
Accuracy Assessment ◽  
Low Cost ◽  
Cost Effective ◽  
Careful Consideration ◽  
Ground Control ◽  
Unmanned Aerial Systems ◽  
Control Points ◽  
Earthen Dam ◽  
Ground Control Points

Small unmanned aerial systems (UAS) represent a cost-effective strategy for topographic surveys. These low-cost drones can provide useful information for 3D reconstruction even if they are equipped with a low-quality navigation system. To ensure the production of high-quality topographic models, careful consideration of flight mode and proper distribution of ground control points is required. To this end a commercial drone has been adopted to monitor a small earthen dam using different combinations of flight configurations and adopting a variable number of ground control points (GCPs). Results highlighted that both choice and combination of flight plans can reduce the relative error of the 3D model up to a few meters without the need of including GCPs. The use of GCPs allows the quality of topographic survey to be greatly improved, reducing error to the order of a few centimeters. In particular, the combined use of images extracted from two flights, one with a camera mounted at nadir and the second with a 20&deg; angle, proves extremely beneficial to increase the overall accuracy of the 3D model and especially of the vertical precision.

scholarly journals Glacier topography and elevation changes from Pléiades very high resolution stereo images

2014 ◽  
Vol 8 (5) ◽  
pp. 4849-4883 ◽  
Author(s):  
E. Berthier ◽  
C. Vincent ◽  
E. Magnússon ◽  
Á. Þ. Gunnlaugsson ◽  
P. Pitte ◽  
...  
Keyword(s):  
Field Measurements ◽  
Ground Control ◽  
European Alps ◽  
Control Points ◽  
Mass Balances ◽  
Ground Control Points ◽  
Digital Elevation ◽  
Stereo Imagery ◽  
Elevation Changes ◽  
Very High

Abstract. In response to climate change, most glaciers are losing mass and hence contribute to sea-level rise. Repeated and accurate mapping of their surface topography is required to estimate their mass balance and to extrapolate/calibrate sparse field glaciological measurements. In this study we evaluate the potential of Pléiades sub-meter stereo imagery to derive digital elevation models (DEMs) of glaciers and their elevation changes. Our five validation sites are located in Iceland, the European Alps, the Central Andes, Nepal and Antarctica. For all sites, nearly simultaneous field measurements were collected to evaluate the Pléiades DEMs. For Iceland, the Pléiades DEM is also compared to a Lidar DEM. The vertical biases of the Pléiades DEMs are less than 1 m if ground control points (GCPs) are used, but reach up to 6 m without GCPs. Even without GCPs, vertical biases can be reduced to a few decimetres by horizontal and vertical co-registration of the DEMs to reference altimetric data on ice-free terrain. Around these biases, the vertical precision of the Pléiades DEMs is ±1 m and even ±0.5 m on the flat glacier tongues (1-sigma confidence level). We also demonstrate the high potential of Pléiades DEMs for measuring seasonal, annual and multi-annual elevation changes with an accuracy of 1 m or better. The negative glacier-wide mass balances of the Argentière Glacier and Mer de Glace (−1.21 ± 0.16 and −1.19 ± 0.16 m.w.e. yr−1, respectively) are revealed by differencing SPOT5 and Pléiades DEMs acquired in August 2003 and 2012 demonstrating the continuing rapid glacial wastage in the Mont-Blanc area.

scholarly journals A Framework for Multiple Ground Target Finding and Inspection Using a Multirotor UAS

Sensors ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 272 ◽  
Author(s):  
Ajmal Hinas ◽  
Roshan Ragel ◽  
Jonathan Roberts ◽  
Felipe Gonzalez
Keyword(s):  
Target Detection ◽  
Low Cost ◽  
Target Position ◽  
Position Estimation ◽  
Quality Data ◽  
Unmanned Aerial Systems ◽  
Modular Software ◽  
Ground Target ◽  
High Level ◽  
Aerial Systems

Small unmanned aerial systems (UASs) now have advanced waypoint-based navigation capabilities, which enable them to collect surveillance, wildlife ecology and air quality data in new ways. The ability to remotely sense and find a set of targets and descend and hover close to each target for an action is desirable in many applications, including inspection, search and rescue and spot spraying in agriculture. This paper proposes a robust framework for vision-based ground target finding and action using the high-level decision-making approach of Observe, Orient, Decide and Act (OODA). The proposed framework was implemented as a modular software system using the robotic operating system (ROS). The framework can be effectively deployed in different applications where single or multiple target detection and action is needed. The accuracy and precision of camera-based target position estimation from a low-cost UAS is not adequate for the task due to errors and uncertainties in low-cost sensors, sensor drift and target detection errors. External disturbances such as wind also pose further challenges. The implemented framework was tested using two different test cases. Overall, the results show that the proposed framework is robust to localization and target detection errors and able to perform the task.

Sign in / Sign up

Export Citation Format

Share Document