scholarly journals Two-Phase Flow Mass Transfer Analysis of Airlift Pump for Aquaculture Applications

Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 226
Author(s):  
Rashal Abed ◽  
Mohamed M. Hussein ◽  
Wael H. Ahmed ◽  
Sherif Abdou
Keyword(s):  
Mass Transfer ◽  
Oxygen Transfer ◽  
Transfer Rate ◽  
Two Phase Flow ◽  
Oxygen Transfer Rate ◽  
Flow Patterns ◽  
Oxygen Mass Transfer ◽  
Phase Flow ◽  
Two Phase ◽  
Airlift Pump

Airlift pumps can be used in the aquaculture industry to provide aeration while concurrently moving water utilizing the dynamics of two-phase flow in the pump riser. The oxygen mass transfer that occurs from the injected compressed air to the water in the aquaculture systems can be experimentally investigated to determine the pump aeration capabilities. The objective of this study is to evaluate the effects of various airflow rates as well as the injection methods on the oxygen transfer rate within a dual injector airlift pump system. Experiments were conducted using an airlift pump connected to a vertical pump riser within a recirculating system. Both two-phase flow patterns and the void fraction measurements were used to evaluate the dissolved oxygen mass transfer mechanism through the airlift pump. A dissolved oxygen (DO) sensor was used to determine the DO levels within the airlift pumping system at different operating conditions required by the pump. Flow visualization imaging and particle image velocimetry (PIV) measurements were performed in order to better understand the effects of the two-phase flow patterns on the aeration performance. It was found that the radial injection method reached the saturation point faster at lower airflow rates, whereas the axial method performed better as the airflow rates were increased. The standard oxygen transfer rate (SOTR) and standard aeration efficiency (SAE) were calculated and were found to strongly depend on the injection method as well as the two-phase flow patterns in the pump riser.

scholarly journals An Experimental Study on the Mass Transfer Rate of Droplets in Annular Two-Phase Flow

2006 ◽  
Vol 49 (2) ◽  
pp. 271-278 ◽  
Author(s):  
Tomio OKAWA ◽  
Naoya SHIMADA ◽  
Akio KOTANI ◽  
Isao KATAOKA
Keyword(s):  
Mass Transfer ◽  
Experimental Study ◽  
Transfer Rate ◽  
Two Phase Flow ◽  
Mass Transfer Rate ◽  
Phase Flow ◽  
Two Phase

Numerical study on gas–liquid two-phase flow and mass transfer in a microchannel

2021 ◽  
Vol 19 (3) ◽  
pp. 295-308
Author(s):  
Jin Zunlong ◽  
Liu Yonghao ◽  
Dong Rui ◽  
Wang Dingbiao ◽  
Chen Xiaotang
Keyword(s):  
Mass Transfer ◽  
Surface Tension ◽  
Slug Flow ◽  
Transfer Rate ◽  
Numerical Study ◽  
Mass Transfer Rate ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
Liquid Plug

Abstract A numerical study of the gas–liquid two-phase flow and mass transfer in a square microchannel with a T-junction is carried out in this work. Through numerical simulation methods, the flow patterns of bubble flow, slug flow and annular flow are determined. By proposing a new flow pattern conversion relationship with different media and different speeds, 100 sets of CO2-water flow patterns and 100 sets of CO2-ethanol flow patterns are obtained. The effects of surface tension on flow pattern, bubble length and liquid plug length are studied. The pressure distribution and pressure drop are analyzed, and mass transfer is obtained through slug flow simulation, and the influencing factors of gas–liquid mass transfer are studied. The results show that the effect of surface tension on the length of the bubble and the length of the liquid plug is completely opposite, the pressure distribution is stepped, and the pressure drop increases with the increase of the gas–liquid velocity. In addition, it was found that the volumetric mass transfer coefficients of the bubble cap and the liquid film gradually decreased with time, and eventually stabilized. The increase in bubble velocity accelerates the mass transfer rate, while the increase in unit cell length slows the mass transfer rate. However, the influence of film thickness and liquid film length on mass transfer varies with time.

scholarly journals Liquid–liquid two-phase flow patterns and mass transfer characteristics in rectangular glass microreactors

2008 ◽  
Vol 63 (16) ◽  
pp. 4035-4044 ◽  
Author(s):  
Anne-Laure Dessimoz ◽  
Laurent Cavin ◽  
Albert Renken ◽  
Lioubov Kiwi-Minsker
Keyword(s):  
Mass Transfer ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
Transfer Characteristics ◽  
Rectangular Glass

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2003 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Micro Channels

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.

Sign in / Sign up

Export Citation Format

Share Document