Metasurfaces for Far-Field Radiation Pattern Correction of Antennas under Dielectric Seamed-Radomes

A high-index dielectric radome seam is camouflaged with respect to a low-index dielectric radome panel by tuning the seam with carefully engineered metasurfaces. A transmission-line approach is used to model the metasurface-tuned seam and analytically retrieve the corresponding surface impedance, from which the unit-cell design is then tailored. Full-wave simulations and microwave antenna measurements performed on a proof-of-concept prototype validate the undesired scattering suppression effect in the case of normally and obliquely incident transverse electric and transverse magnetic wave illuminations. Robustness of the proposed solution to fabrication tolerances is also reported. The study presents metasurface-tuning as an easily implementable, frequency adjustable, and polarization insensitive solution to reduce the scattering of dielectric mechanical seams and improve the overall transparency performance of radome structures.

Super Strong Wide TM Mie Bandgaps Tolerating Disorders

This study demonstrates the appearance of super intense and wide Mie bandgaps in metamaterials composed of germanium rods in air that tolerate some disordering of rod position and rod radius under transverse magnetic (TM) polarized light waves. Results for Mie bandgap modes TM01 and TM11 tolerate rod-position disordering of 50%, and rod-radius disordering of 34 and 20%, respectively. Using these characteristics of TM11 under position and radius disordering, ultra-narrow straight, L-shaped and crossing waveguides that contain 14, four, and two rows of Ge rods in air are designed. Also, it is shown that TE01 Mie bandgap appear in metamaterials contain high refractive index, and disappear in metamaterials with lower refractive index such as silicon; in contrast, a new phenomenon of intense and broadband TM01, TM11, and TM21 in metamaterials with lower refractive index such as silicon appear. Also, in Si-based metamaterials, TM01 tolerates high rod-position and rod-radius disordering of 50% and 34%, respectively, and TM11 shows robustness to rod-position and rod-radius of 20%. This strong tolerance of disordering of TM modes in silicon and germanium metamaterials opens a new way to design small, high-efficient, and easy-fabricable optical devices for optical integrated circuits.

Sensitivity characterization of polarization operating by embedded reflective grating

In this paper, a novel embedded reflective grating (ERG) is presented to realize bi-function polarization operating at infrared band by finite element analysis (FEM). For transverse electric (TE) polarization, a two-port output (0th and −2nd orders) with an efficiency of more than 47% and excellent uniformity can be obtained. For transverse magnetic (TM) polarization, a high efficiency output of 94.72% can be achieved at the −2th order. The results of the analysis of the electric field intensity distribution, angular and wavelength bandwidths further demonstrate the advantages of the proposed grating. In addition, the tolerance analysis of period and duty cycle prove the feasibility of the grating in practical production.

Stack-based grating for wideband polarization splitter in terahertz

A novel wideband terahertz polarization beam splitter with special diffraction orders working at terahertz band is described in this paper. The polarizer can achieve high diffraction efficiency and uniformity in the 2.50 - 2.56 THz band. Based on rigorous coupled-wave analysis (RCWA) and simulated annealing algorithm, we proposed an efficient algorithm to optimize the polarizer. After calculations, 98.45% single-port high-efficiency reflection for transverse electric (TE) polarization and 42.33%/42.57% highly uniform dual-port beam splitting for transverse magnetic (TM) polarization were finally obtained. In addition, through RCWA and simplified modal method, the electromagnetic field distributions of TE and TM polarizations are shown visually and described quantitatively. Moreover, the results displayed in Sec. 3 prove that the grating possesses the characteristics of relatively large bandwidth and insensitivity to the incident angle. Therefore, the novel scheme in this paper has great reference value for the research of terahertz modulation devices and the integration of terahertz communication systems.

Rapid and Highly Sensitive Detection of C-Reaction Protein Using Robust Self-Compensated Guided-Mode Resonance BioSensing System for Point-Of-Care Applications

The rapid and sensitive detection of human C-reactive protein (CRP) in a point-of-care (POC) may be conducive to the early diagnosis of various diseases. Biosensors have emerged as a new technology for rapid and accurate detection of CRP for POC applications. Here, we propose a rapid and highly stable guided-mode resonance (GMR) optofluidic biosensing system based on intensity detection with self-compensation, which substantially reduces the instability caused by environmental factors for a long detection time. In addition, a low-cost LED serving as the light source and a photodetector are used for intensity detection and real-time biosensing, and the system compactness facilitates POC applications. Self-compensation relies on a polarizing beam splitter to separate the transverse-magnetic-polarized light and transverse-electric-polarized light from the light source. The transverse-electric-polarized light is used as a background signal for compensating noise, while the transverse-magnetic-polarized light is used as the light source for the GMR biosensor. After compensation, noise is drastically reduced, and both the stability and performance of the system are enhanced over a long period. Refractive index experiments revealed a resolution improvement by 181% when using the proposed system with compensation. In addition, the system was successfully applied to CRP detection, and an outstanding limit of detection of 1.95 × 10−8 g/mL was achieved, validating the proposed measurement system for biochemical reaction detection. The proposed GMR biosensing sensing system can provide a low-cost, compact, rapid, sensitive, and highly stable solution for a variety of point-of-care applications.

Rigorous accounting diffraction on non-plane gratings irradiated by non-planar waves

The modified boundary integral equation method (MIM) is considered a rigorous theoretical application for the diffraction of cylindrical waves by arbitrary profiled plane gratings, as well as for the diffraction of plane/non-planar waves by concave/convex gratings. This study investigates two-dimensional (2D) diffraction problems of the filiform source electromagnetic field scattered by a plane lamellar grating and of plane waves scattered by a similar cylindrical-shaped grating. Unlike the problem of plane wave diffraction by a plane grating, the field of a localised source does not satisfy the quasi-periodicity requirement. Fourier transform is used to reduce the solution of the problem of localised source diffraction by the grating in the whole region to the solution of the problem of diffraction inside one Floquet channel. By considering the periodicity of the geometry structure, the problem of Floquet terms for the image can be formulated so that it enables the application of the MIM developed for plane wave diffraction problems. Accounting of the local structure of an incident field enables both the prediction of the corresponding efficiencies and the specification of the bounds within which the approximation of the incident field with plane waves is correct. For 2D diffraction problems of the high-conductive plane grating irradiated by cylindrical waves and the cylindrical high-conductive grating irradiated by plane waves, decompositions in sets of plane waves/sections are investigated. The application of such decomposition, including the dependence on the number of plane waves/sections and radii of the grating and wave front shape, was demonstrated for lamellar, sinusoidal and saw-tooth grating examples in the 0th & –1st orders as well as in the transverse electric and transverse magnetic polarisations. The primary effects of plane wave/section partitions of non-planar wave fronts and curved grating shapes on the exact solutions for 2D and three-dimensional (conical) diffraction problems are discussed.

Performance Analysis of ZigBeePRO Network Using the Shortest Path Algorithm for Distributed Renewable Generation

The communication requirement for integrating Distributed Renewable Generation (DRG) into Smart Grid (SG) is not strict, where the reliability and critical demand of data delivery are compromised due to the low-data rate and power of ZigBee. However, the presence of various dielectric constant materials in the DRG can cause transmission impairments of the electromagnetic wave. In this paper, we have analysed the performance of the ZigBeePRO network by applying the shortest path algorithm while delivering energy data from the solar DRG to the SG. The DRG architecture is created by considering a real test-bed of 35 kW solar DRG at Universiti Putra Malaysia (UPM). The numbers of nodes are calculated from specifications of the ZigBeePRO enabled Waspmote embedded board, inverters, and electrical parameters of a Photovoltaic (PV) module. The results of the obtained propagation path loss model indicate that the Transverse Electric (TE) and Transverse Magnetic (TM) polarizations are proportional to the loss of the propagation path at different incident angles (α); however, an exception is observed for the TM polarization at α = 55 o. Due to this polarization effect, the brick-built type cabin at the DRG site is a consequence of a higher propagation path loss than the Iron (III)-made cabin. The other performance parameters, including network throughput, data loss, and ZigBeePRO collision, are also evaluated.