scholarly journals Selection of Machining Parameters Using a Correlative Study of Cutting Tool Wear in High-Speed Turning of AISI 1045 Steel

2018 ◽  
Vol 2 (4) ◽  
pp. 66 ◽  
Author(s):  
Luis Hernández González ◽  
Yassmin Seid Ahmed ◽  
Roberto Pérez Rodríguez ◽  
Patricia Zambrano Robledo ◽  
Martha Guerrero Mata
Keyword(s):  
High Speed ◽  
Manufacturing Industry ◽  
Cutting Tool ◽  
Flank Wear ◽  
Machining Parameters ◽  
High Speed Turning ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide

The manufacturing industry aims to produce many high quality products efficiently at low cost, thereby motivating companies to use advanced manufacturing technologies. The use of high-speed machining is increasingly widespread; however, it lacks a deep-rooted knowledge base needed to facilitate implementation. In this paper, response surface methodology (RSM) has been applied to determine the optimum cutting conditions leading to minimum flank wear in high-speed dry turning on AISI 1045 steel. The mathematical models in terms of machining parameters were developed for flank wear prediction using RSM on the basis of experimental results. The high speed turning experiments were carried out with two coated carbide and a cermet inserts using AISI 1045 steel as work material at different cutting speeds and machining times. The models selected for optimization were validated through the Pareto principle. Results showed the GC4215 insert to be the most optimal option, because it did not reach the cutting tool life limit and could be used for the whole range of cutting parameters selected. To quantitatively evaluate the usefulness of the cutting tools, it was proposed the coefficient of use of the tools from the results of the contour graphs. The GC4215 insert showed 100% effectiveness, followed by the GC4225 with 98.4%, and finally, the CT5015 insert with 83%.

High Speed Machining of Hardened AISI 1045 Steel

2016 ◽  
Vol 861 ◽  
pp. 63-68 ◽  
Author(s):  
Xue Ping Zhang ◽  
Shu Biao Wu ◽  
Zhen Qiang Yao ◽  
Li Feng Xi
Keyword(s):  
High Speed ◽  
Shear Bands ◽  
Chip Morphology ◽  
Machining Parameters ◽  
Chip Breaker ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
High Feed ◽  
Serrated Chips ◽  
1045 Steel

Hardened AISI 1045 steel implemented in machine tool spindle was previously ground using grinding operation. This research aims to address the feasibility of hard turning AISI 1045 using PCBN tool with chip breaker under dry condition. Chip morphology, cutting force and temperature were measured, analyzed and correlated with machining parameters. Experimental results demonstrate that serrated chips are generated at high speeds, high feed rate is an assistant to promote serrated chips, and chip breaker can help break chip into acceptable lengths. Cutting forces were characterized with periodic fluctuation along three directions as chips are serrated. Temperature at machined zone can reach as high as 1200°C, which indicates that adiabatic shear bands can be successfully achieved during the machining of hardened AISI 1045 steel without applying lubricants.

Predictive Modeling of Turning Operations Using Response Surface Methodology

2013 ◽  
Vol 307 ◽  
pp. 170-173 ◽  
Author(s):  
Girish Kant ◽  
Vaibhav Rao V ◽  
Kuldip Singh Sangwan
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Cutting Tool ◽  
Machining Parameters ◽  
Turning Operations ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Predicted Values ◽  
Cutting Tool Insert ◽  
1045 Steel

This paper focuses on the development of a predictive model using the measured forces acting on the cutting tool during turning operation of AISI 1045 Steel using a Tungsten Carbide cutting tool insert. On the basis of the experimental results, second order mathematical model is developed in terms of machining parameters by using the Response Surface Methodology (RSM). The results are analyzed statistically and graphically. It has been observed that the predicted values using RSM also follow the same trend as given by the measured values.

scholarly journals FINITE ELEMENT MODELING OF TEMPERATURE FIELDS ON THE CUTTING EDGE IN THE DRY HIGH-SPEED TURNING OF AISI 1045 STEEL

2020 ◽  
Vol 18 (2) ◽  
pp. 205
Author(s):  
Roberto Pérez ◽  
Luis Hernández ◽  
Ana Quesada ◽  
Julio Pino ◽  
Enrique Zayas
Keyword(s):  
Finite Element ◽  
Temperature Field ◽  
High Speed ◽  
Cutting Tools ◽  
Temperature Fields ◽  
High Speed Turning ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Conventional Machining

High-speed turning is an advanced and emerging machining technique that, in contrast to the conventional machining, allows the manufacture of the workpiece with high accuracy, efficiency and quality, with lower production costs and with a considerable reduction in the machining times. The cutting tools used for the conventional machining cannot be employed for high-speed machining due to a high temperature induced in machining and a lower tool life. Therefore, it is necessary to study the influence of high cutting speeds on the temperature distribution in different typologies of cutting tools, with the aim of evaluating their behavior. In this paper, a finite element method modeling approach with arbitrary Lagrangian-Eulerian fully coupled thermal-stress analysis is employed. The research presents the results of different cutting tools (two coated carbide tools and uncoated cermet) effects on average surface temperature fields on the cutting edge in the dry high-speed turning of AISI 1045 steel. The numerical experiments were designed based on different cutting tools like input parameters and different temperature field zones like dependent variables in the dry high-speed turning of AISI 1045 steel. The results indicate that the dry high-speed turning of AISI 1045 steel does not influence significantly the temperature field zones when P10, P15 or P25 inserts are used. Therefore, the use of a dry high-speed turning method, which reduces the amount of lubricant and increases productivity, may represent an alternative to turning to the extent here described.

Investigation of the Effects of Microgrooved Cutting Tool in High Speed Machining of AISI 1045 Steel

2017 ◽  
Author(s):  
Xingbang Chen ◽  
Nick H. Duong ◽  
J. Ma ◽  
Shuting Lei
Keyword(s):  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Contact Length ◽  
High Speed Machining ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Cutting Inserts ◽  
1045 Steel

In this paper, numerical investigation of the effects of microgroove textured cutting tools in high speed machining of AISI 1045 is conducted using Finite Element Method (FEM). Microgrooves are designed and fabricated on the rake face of cemented carbide (WC/Co) cutting inserts. The effects of microgroove width, edge distance (the distance from cutting edge to the first microgroove), and microgroove depth are examined and assessed in terms of main cutting force, thrust force, and tool-chip contact length. It is found that microgrooved cutting tools generate lower cutting force and consequently lower the energy necessary for machining. This research provides insightful guidance for optimizing tool life and reducing energy consumption in high-speed machining of AISI 1045 steel.

Tool Wear Analysis on Multi-Layered Coated Carbide Tools in Face Milling of AISI 1045 Steel

2010 ◽  
Author(s):  
Kyung-Hee Park ◽  
Patrick Y. Kwon
Keyword(s):  
Tool Wear ◽  
Flank Wear ◽  
Face Milling ◽  
Coating Materials ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide ◽  
Coated Carbide Tools ◽  
Layer Coating

Face milling tests on AISI 1045 steel were performed to study the flank wear of multilayered coated carbide tools. The cutting tools were dual (TiN/TiAlN) and triple (TiN/Al2O3/TiCN) layered, coated carbide inserts processed by PVD and CVD respectively. As expected, the depth of cut (DOC) did not play an important role on the development of flank wear while the cutting speed had a significant role in the development of flank wear. Using confocal laser scanning microscopy (CLSM) and wavelet transform, the flank wear evolution was analyzed and abrasive wear was found to be a dominant tool wear mechanism. Adhesion of the work material was also observed after the carbide substrate was exposed. Edge chipping and micro-fracture were additional tool failure modes. After comparing the performance of the two inserts, we concluded that the dual layer coating was superior to the triple layer coating under various cutting conditions mainly due to the benefit coming from the coating processes themselves. It was claimed that the superior performance of the multilayer coating came from preventing the gross crack-induced removal of coating materials by propagating the fracture along the coating interfaces. However, no such observations were found in our milling experiment. Therefore, the hardness of the coating materials is the most important criteria for the development of flank wear.

New Thermal Issues on the Modelling of Tool-Workpiece Interaction: Application to Dry Cutting of AISI 1045 Steel

2011 ◽  
Vol 223 ◽  
pp. 286-295 ◽  
Author(s):  
Cédric Courbon ◽  
Tarek Mabrouki ◽  
Joël Rech ◽  
Denis Mazuyer ◽  
Enrico D'Eramo
Keyword(s):  
Heat Flux ◽  
Hot Spot ◽  
Orthogonal Cutting ◽  
Chip Thickness ◽  
Contact Length ◽  
Dry Cutting ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide

The present work proposes to enhance the thermal interface denition in Finite Element (FE) simulations of machining. A user subroutine has been developed in Abaqus/Explicit © to implement a new experimentally-based heat partition model extracted from tribological tests. A 2D Arbitrary-Lagragian-Eulerian (ALE) approach is employed to simulate dry orthogonal cutting of AISI 1045 steel with coated carbide inserts. Simulation results are compared to experimental ones over a whole range of cutting speeds and feed rates in terms of average cutting forces, chip thickness, tool chip contact length and heat flux. This study emphasizes that heat transfer and temperature distribution in the cutting tool are drastically in uenced by the thermal formulation used at the interface. Consistency of the numerical results such as heat flux transmitted to the tool, peak temperature as well as hot spot location can be denitively improved.

scholarly journals Assessment of CVD- and PVD-Coated Carbides and PVD-Coated Cermet Inserts in the Optimization of Surface Roughness in Turning of AISI 1045 Steel

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5231
Author(s):  
Evandro Paese ◽  
Martin Geier ◽  
Fabiano R. Rodrigues ◽  
Tadeusz Mikolajczyk ◽  
Mozammel Mia
Keyword(s):  
Surface Quality ◽  
Material Removal Rate ◽  
Vapor Deposition ◽  
Material Removal ◽  
Removal Rate ◽  
Controllable Factors ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide

In this study, an experimental and statistic investigation approach based on analysis of variance (ANOVA) and response surface methodology (RSM) techniques was performed to find the significant main effects and two-factor interaction effects and to determine how the controllable factors such as cutting speed, feed rate, depth of cut (DOC), tool nose radius, substrate and coating method of cutting tools influence surface quality in turning of AISI 1045 steel. The first optimal or near-optimal conditions for the quality of the generated surface and the second ones, including maximum material removal rate, were established using the proposed regression equations. The group mean roughness of the turned workpieces was lower from using chemical vapor deposition (CVD)-coated carbide inserts than the group means of other types of inserts; however they could not achieve the specific lowest roughness. The physical vapor deposition (PVD)-coated carbide and cermet inserts achieved the best surface quality when the specific combinations within the range interval of controllable factors were used in the experiment, showing that they may be applied to finish turning processes or even to particular high material removal rate conditions associated with the lowest roughness.

New Experiments on the Temperature Distribution in Drilling

1984 ◽  
Vol 106 (3) ◽  
pp. 242-247 ◽  
Author(s):  
A. Thangaraj ◽  
P. K. Wright ◽  
M. Nissle
Keyword(s):  
Temperature Distribution ◽  
High Speed ◽  
Metal Flow ◽  
High Speed Steel ◽  
Twist Drill ◽  
Temperature Distributions ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Twist Drills

Using metallographic and microhardness techniques, temperature distributions have been determined in twist drills. The methods rely on the fact that certain high speed steel materials exhibit microstructural changes when subjected to temperatures greater than 600°C. Quick-stop specimens have also been obtained to study the metal flow patterns over the drill flutes. These results have been used to comment on the different wear mechanisms that affect the performance of a twist drill. Preliminary results show that bulk plastic flow occurs near the margin of the drill where the temperatures are in the vicinity of 900°C when machining AISI 1045 steel at 40 m/min.

Identification of a Friction Model at the Tool-Chip-Workpiece Interface in Dry Machining of a AISI 1045 Steel With a TiN Coated Carbide Tool

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Hamdi Ben Abdelali ◽  
Cedric Courbon ◽  
Joël Rech ◽  
Wacef Ben Salem ◽  
Abdelwaheb Dogui ◽  
...  
Keyword(s):  
Friction Model ◽  
Carbide Tool ◽  
Dry Machining ◽  
Sliding Velocity ◽  
Partition Model ◽  
Heat Partition ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Coated Carbide

The characterization of frictional phenomena at the tool-chip-workpiece interface in metal cutting remains a challenge. This paper aims at identifying a friction model and a heat partition model at this interface during the dry cutting of an AISI1045 steel with TiN coated carbide tools. A new tribometer, based on a modified pin-on-ring system, has been used in order to reach relevant values of pressures, temperatures, and sliding velocities. Additionally a 3D Arbitrary Lagrangian Eulerian model (A.L.E.) numerical model simulating the frictional test has been developed in order to extract local parameters around the spherical pin, such as average contact pressure, average local sliding velocity, and average contact temperature, from experimental macroscopic measurements. A large range of sliding velocities [0.083–5 m/s] has been investigated. It has been shown that friction coefficient and heat partition coefficient are mainly dependant on local sliding velocity at the interface. Three friction regimes have been identified. These experimental and numerical results provide a better understanding of the tribological phenomena along the tool-chip-workpiece interfaces in dry machining of an AISI 1045 steel with a TiN coated carbide tool. Finally a new friction model and heat partition model has been developed for implementation in a numerical cutting model.

Sign in / Sign up

Export Citation Format

Share Document