scholarly journals Development and Investigation of an Inexpensive Low Frequency Vibration Platform for Enhancing the Performance of Electrical Discharge Machining Process

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6192
Author(s):  
Abhimanyu Singh Mertiya ◽  
Aman Upadhyay ◽  
Kaustubh Nirwan ◽  
Pravin Pandit Harane ◽  
Ahmad Majdi Abdul-Rani ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Low Frequency ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Low Frequency Vibration ◽  
Debris Removal ◽  
Vibration Assistance ◽  
Discharge Gap

Difficulty in debris removal and the transport of fresh dielectric into discharge gap hinders the process performance of electrical discharge machining (EDM) process. Therefore, in this work, an economical low frequency vibration platform was developed to improve the performance of EDM through vibration assistance. The developed vibratory platform functions on an eccentric weight principle and generates a low frequency vibration in the range of 0–100 Hz. The performance of EDM was evaluated in terms of the average surface roughness (Ra), material removal rate (MRR), and tool wear rate (TWR) whilst varying the input machining parameters viz. the pulse-on-time (Ton), peak current (Ip), vibration frequency (VF), and tool rotational speed (TRS). The peak current was found to be the most significant parameter and contributed by 78.16%, 65.86%, and 59.52% to the Ra, MRR, and TWR, respectively. The low frequency work piece vibration contributed to an enhanced surface finish owing to an improved flushing at the discharge gap and debris removal. However, VF range below 100 Hz was not found to be suitable for the satisfactory improvement of the MRR and reduction of the TWR in an electrical discharge drilling operation at selected machining conditions.

scholarly journals Comparative Study on EDM of Ti-6Al-4V Using Circular and Convex Shaped Electrodes

2018 ◽  
Vol 7 (3.34) ◽  
pp. 256
Author(s):  
S Rajamanickam ◽  
R Palani ◽  
V Sathyamoorthy ◽  
Muppala Jagadeesh Varma ◽  
Shaik Shaik Mahammad Althaf ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Industrial Applications ◽  
Copper Electrode ◽  
Machining Process ◽  
Project Work ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

As on today, Electrical Discharge Machining (EDM) is world famous unconventional machining process for electrically conductive materials. In this project work, Ti-6Al-4V is performed in electrical discharge machining using differently shaped (circular and convex) copper electrode. The machining parameters considered are the pulse on- time, pulse off-time, voltage and current to investigate machining characteristics like material removal rate and tool wear rate. Taguchi method is applied to frame experimental design. Ti-6Al-4V finds wide usage in industrial applications such as marine, aerospace, bio-medical and so on. 

Evaluation of Electrical Discharge Machining Performance on Al (6351)–SiC–B4C Composite

2019 ◽  
pp. 109-124
Author(s):  
Uthayakumar M. ◽  
Suresh Kumar S. ◽  
Thirumalai Kumaran S. ◽  
Parameswaran P.
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Research Work ◽  
Machining Process ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machined Surface ◽  
Output Performance ◽  
B4c Particles

Electrical discharge machining (EDM) process is a non-conventional machining process used for the material which are difficult to machine. In this research work, an attempt has been made to determine the influence of Boron Carbide (B4C) particles on the machinablity of the Al (6351) alloy reinforced with 5 wt. % Silicon Carbide (SiC) Metal Matrix Composite (MMC) through EDM. Influence of machining parameters such as pulse current (I), pulse on time (Ton), duty factor (τ), and gap voltage (V) on affecting the output performance characteristics namely Electrode Wear Ratio (EWR), Surface Roughness (SR) and Power Consumption (PC) which are studied. The result shows that the addition of B4C particles significantly affects the machinablity of the composite, with a contribution of 1.6% on EWR, 3.5% on SR and 19.8% on PC. The crater, recast layer formation, and Heat Affected Zone (HAZ) in the machined surface of the composite are also reported in detail.

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

The surface integrity of ultra-fine grain steel, Electrical discharge machined using Iso-pulse and resistance–capacitance-type generator

2020 ◽  
Vol 234 (4) ◽  
pp. 564-573
Author(s):  
Mohammad S Mahdieh
Keyword(s):  
Surface Integrity ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
High Strength ◽  
Functional Method ◽  
Machining Process ◽  
Machining Parameters ◽  
Fine Grained ◽  
Hardness Tester ◽  
Angular Pressing

Ultra-fine grained materials with high strength and low weight are eventually considered to be used in industries. To produce ultra-fine grained materials, equal channel angular pressing is a functional method, imposing severe plastic deformation on the workpiece. Electrical discharge machining is an indispensable process in manufacturing industrial parts with high accuracy and precision. However, electrical discharge machining has thermo-physical consequences, damaging the surface layers of the workpiece. On the other hand, the ultra-fine grained materials are thermodynamically unstable and tend to microstructural evolution. Thus, electrical discharge machining process affects the ultra-fine grained materials more than coarse grain materials. In this study, the effects of electrical discharge machining on the ultra-fine grained steel were investigated and the undesirable influences of the electrical discharge machining were diminished by adjusting the electrical discharge machining parameters. The ultra-fine grained steel samples were electrical discharge machined in two methods including Iso-pulse (roughing mode and finishing mode) and with resistance–capacitance-type generator. The surface integrity parameters, including thickness and microstructure of the recast layer and heat-affected zone, the cracks density and hardness, which for all three types of samples, were investigated by scanning electron microscopy, optical microscopy, X-ray diffraction technique, and micro-hardness tester. The results show that electrical discharge machining with resistance–capacitance-type generator has the minimum effects on the surface integrity of the ultra-fine grained samples because of the different material removal mechanism of resistance–capacitance-type electrical discharge machining.

Comparative study of low-frequency vibrations assigned to a workpiece in EDM and PMEDM

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040145
Author(s):  
Quang Dung Le ◽  
Huu Phan Nguyen ◽  
Tien Long Banh ◽  
Duc Toan Nguyen
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Low Frequency ◽  
Quality Measures ◽  
Processing Efficiency ◽  
Machined Surface ◽  
Low Frequency Vibration ◽  
Better Than

This study deals about the influence of vibrations incorporated into a workpiece during powder-mixed electrical discharge machining (PMEDM) on quality measures such as material removal rate (MRR), surface roughness [Formula: see text] and microhardness. It has been found that the low-frequency vibration incorporated into the workpiece positively affects the processing efficiency of electrical discharge machining (EDM) and PMEDM. However, the effect of low-frequency vibration in PMEDM has been better than EDM. The higher vibration frequency significantly improves the MRR and [Formula: see text] in PMEDM. The MRR has been improved by 95.89% and with lower [Formula: see text] of 63.2% in PMEDM. The hardness of the machined surface after PMEDM using titanium powder mixed in dielectric liquid was increased approximately two times as compared with conventional EDM.

An Investigation of the Influences of EDM Parameters and Tool Geometries on Radial Overcut for Monel 400 Material with Tungsten Copper Electrode

2015 ◽  
Vol 766-767 ◽  
pp. 908-913
Author(s):  
P. Padmini ◽  
S. Senthamilperarasu ◽  
B. Shanmuganathan ◽  
N.R.R. Anbusagar ◽  
P. Sengottuvel
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dimensional Accuracy ◽  
Copper Electrode ◽  
Machining Process ◽  
Experimental Result ◽  
Machining Parameters ◽  
Radial Overcut ◽  
Monel 400 ◽  
Pulse On Time

Electrical-discharge Machining (EDM) is a nonconventional machining process utilizing an electric spark discharge from the electrode (-) towards the work piece (+) through the dielectric fluid. The Dimensional accuracy in this is very important consideration for the accuracy of the finished product. The objective of this experimental study is to determine parameters that offer the best dimensional accuracy in electrical discharge machining (EDM). Discharge current (A), Pulse On Time (Ton), Pulse Off Time (Toff ) and Circle,Rectangle,Triangle and Square Tool Geometrical Shapes (Geo) are taken as machining parameters. The experimental investigations are carried out on Monel 400 material using Tungsten copper electrode. The response of ROC is considered for improving the machining efficiency. Optimal combination of parameters was obtained Taguchi Optimization technique. The confirmation experiments results shows that the significant improvement in Radial Overcut was obtained. ANOVA have been used to analyze the contribution of individual parameters on ROC. The experimental result demonstrates that the Taguchi method satisfies the practical requirements

Sign in / Sign up

Export Citation Format

Share Document