scholarly journals Nanofluid Convective Heat Transfer Enhancement Elliptical Tube inside Circular Tube under Turbulent Flow

2018 ◽  
Vol 23 (4) ◽  
pp. 78
Author(s):  
Suad Danook ◽  
Qusay Jasim ◽  
Adnan Hussein
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Transfer Rate ◽  
Circular Tube ◽  
Uniform Heat Flux ◽  
Governing Equations ◽  
Transfer Enhancement ◽  
Enhance Heat Transfer ◽  
Electrical Heater ◽  
Volume Method

Heat transfer enhancement employing an elliptical tube inside a circular tube to increase the heat transfer rate without increasing in pressure drop is investigated. The flow rate inside the narrow is in the range of Reynolds number 10,000 to 100,000. Commercial software is used to solve the governing equations (continuity, momentum, and energy) by adopting a finite volume method (FVM). The electrical heater is connected around the circular tube to apply uniform heat flux (3000 W/m2) as a boundary condition. The volume concentrations are in the range of 0.25% to 1% with different TiO2 nanoparticle diameters in the range of 27 nm to 50 nm dispersed in water. The results indicate that the elliptical annulus tube can enhance heat transfer and friction factor by approximately 19% and 6% than the circular tube respectively. Results show that the heat transfer enhancement is significantly increasing as the volume concentrations increase and the nanoparticles size diameter decrease.

scholarly journals Heat transfer enhancement with elliptical tube under turbulent flow TiO2-water nanofluid

2016 ◽  
Vol 20 (1) ◽  
pp. 89-97 ◽  
Author(s):  
Adnan Hussein ◽  
R.A. Bakar ◽  
K. Kadirgama ◽  
K.V. Sharma
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Transfer Rate ◽  
Circular Tube ◽  
Uniform Heat Flux ◽  
Transfer Enhancement ◽  
Enhance Heat Transfer ◽  
Electrical Heater ◽  
Fluent Software ◽  
Volume Method

Heat transfer and friction characteristics were numerically investigated, employing elliptical tube to increase the heat transfer rate with a minimum increase of pressure drop. The flow rate of the tube was in a range of Reynolds number between 10000 and 100000. FLUENT software is used to solve the governing equation of CFD (continuity, momentum and energy) by means of a finite volume method (FVM). The electrical heater is connected around the elliptical tube to apply uniform heat flux (3000 W/m2) as a boundary condition. Four different volume concentrations in the range of 0.25% to 1% and different TiO2 nanoparticle diameters in the range of 27 nm to 50 nm, dispersed in water are utilized. The CFD numerical results indicate that the elliptical tube can enhance heat transfer and friction factor by approximately 9% and 6% than the circular tube respectively. The results show that the Nusselt number and friction factor increase with decreasing diameters but increasing volume concentrations of nanoparticles.

CFD simulation of heat transfer enhancement in circular tube with twisted tape insert by using nanofluids

2020 ◽  
Vol 21 ◽  
pp. 572-577 ◽  
Author(s):  
A. Natarajan ◽  
R. Venkatesh ◽  
S. Gobinath ◽  
L. Devakumar ◽  
K. Gopalakrishnan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Cfd Simulation ◽  
Circular Tube ◽  
Twisted Tape ◽  
Transfer Enhancement

Heat transfer enhancement in microchannels using ribs and secondary flows

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Karthikeyan Paramanandam ◽  
Venkatachalapathy S. ◽  
Balamurugan Srinivasan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Secondary Flows ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to study the flow and heat transfer characteristics of microchannel heatsinks with ribs, cavities and secondary channels. The influence of length and width of the ribs on heat transfer enhancement, secondary flows, flow distribution and temperature distribution are examined at different Reynolds numbers. The effectiveness of each heatsink is evaluated using the performance factor. Design/methodology/approach A three-dimensional solid-fluid conjugate heat transfer numerical model is used to study the flow and heat transfer characteristics in microchannels. One symmetrical channel is adopted for the simulation to reduce the computational cost and time. Flow inside the channels is assumed to be single-phase and laminar. The governing equations are solved using finite volume method. Findings The numerical results are analyzed in terms of average Nusselt number ratio, average base temperature, friction factor ratio, pressure variation inside the channel, temperature distribution, velocity distribution inside the channel, mass flow rate distribution inside the secondary channels and performance factor of each microchannels. Results indicate that impact of rib width is higher in enhancing the heat transfer when compared with its length but with a penalty on the pressure drop. The combined effects of secondary channels, ribs and cavities helps to lower the temperature of the microchannel heat sink and enhances the heat transfer rate. Practical implications The fabrication of microchannels are complex, but recent advancements in the additive manufacturing techniques makes the fabrication of the design considered in this numerical study feasible. Originality/value The proposed microchannel heatsink can be used in practical applications to reduce the thermal resistance, and it augments the heat transfer rate when compared with the baseline design.

Design of a Microfin Array Heat Sink Using Flow-Induced Vibration to Enhance the Heat Transfer Rate in the Laminar Flow Regime

2001 ◽  
Author(s):  
Jeung Sang Go ◽  
Geunbae Lim ◽  
Hayong Yun ◽  
Sung Jin Kim ◽  
Inseob Song
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Heat Transfer Enhancement ◽  
Flow Regime ◽  
Heat Transfer Rate ◽  
Heat Sink ◽  
Transfer Rate ◽  
Transfer Enhancement ◽  
Air Velocity ◽  
Flow Induced Vibration

Abstract This paper presented design guideline of the microfin array heat sink using flow-induced vibration to increase the heat transfer rate in the laminar flow regime. Effect of the flow-induced vibration of a microfin array on heat transfer enhancement was investigated experimentally by comparing the thermal resistances of the microfin array heat sink and those of a plain-wall heat sink. At the air velocities of 4.4m/s and 5.5 m/s, an increase of 5.5% and 11.5% in the heat transfer rate was obtained, respectively. The microfin flow sensor also characterized the flow-induced vibration of the microfin. It was determined that the microfin vibrates with the fundamental natural frequency regardless of the air velocity. It was also shown that the vibrating displacement of the microfin is increased with increasing air velocity and then saturated over a certain value of air velocity. Based on the numerical analysis of the temperature distribution resulted from microfin vibration and experimental results, a simple heat transfer model (heat pumping model) was proposed to understand the heat transfer mechanism of a microfin array heat sink. Under the geometric and structural constraints, the maximum heat transfer enhancement was obtained at the intersection of the minimum thickness of the microfin and constraint of the bending angle.

Heat Transfer Characteristics of a Circular Channel Inserted Metallic Wire With High Porosity

2010 ◽  
Author(s):  
Mitsutoshi Tendo ◽  
Tetsuaki Takeda
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Enhancement ◽  
Circular Tube ◽  
Copper Wire ◽  
Heat Transfer Surface ◽  
High Porosity ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Metallic Wire

There are several methods for heat transfer enhancement. For example, there are attaching various fins on the heat transfer surface, processing the surface roughly, inserting twisted tape, and so on. These methods increase heat transfer coefficient or area by manufacturing of the heat transfer surface. However, it has to take into consideration the deterioration of the structure strength by attaching the fins on the tube surface with the design of the heat exchanger. The objective of this study is to clarify characteristics of heat transfer and pressure drop in the channel inserted metallic wire with high porosity. A heat transfer experiment has been performed using a horizontal circular tube to obtain the heat transfer characteristics in the channel inserted copper wire. This paper describes the heat transfer and flow characteristics of a heat exchanger tube filled with a high porous material. Fine copper wire (diameter: 0.5 mm) was inserted in a circular tube dominated by thermal conduction and forced convection. Working fluid was air. Hydraulic equivalent diameter was cited as the characteristic length in Nusselt number and Reynolds number. From the results obtained in this experiment, it was found that an amount of heat transfer in the tube with the copper wire was larger than that without one. An effectiveness of heat transfer enhancement increased with the temperature of the heated wall. The amount of heat transfer in the circular tube inserted copper wire, which has 0.993–0.998 of porosity, increased about 15% comparing with the tube having a smooth wall surface under the condition of the constant heat flux and lower than 170°C of the wall temperature.

Sign in / Sign up

Export Citation Format

Share Document