scholarly journals Constitutive Model and Flow Behavior of B1500HS High-Strength Steel During the Hot Deformation Process

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 64 ◽  
Author(s):  
Li ◽  
Duan ◽  
Yao ◽  
Guan ◽  
Yang
Keyword(s):  
Flow Stress ◽  
Constitutive Model ◽  
Hot Deformation ◽  
High Strength Steel ◽  
Deformation Behavior ◽  
Flow Behavior ◽  
Constitutive Models ◽  
High Strength ◽  
Stress Strain ◽  
Comparison Results

Hot compression tests were carried out on a Gleeble-3800 thermal mechanical simulator in the temperature range from 700 to 900 °C and strain rate range from 0.005 to 10 s−1 to investigate the hot deformation behavior of B1500HS high-strength steel. Softening mechanisms of B1500HS high-strength steel under different deformation conditions were analyzed according to the characteristics of flow stress–strain curves. By analyzing and processing the experimental data, the values of steady flow stress, saturated stress, dynamic recovery (DRV) softening coefficient, and other factors were solved and these parameters were expressed as functions of Zener–Hollomon factors. Based on the dislocation density theory and the kinetic model of dynamic recrystallization (DRX), constitutive models corresponding to different softening mechanisms were established. The flow stress–strain curves of B1500HS predicted by a constitutive model are in good agreement with the experimental results and the correlation coefficient is . The comparison results indicate that the constitutive models can accurately reflect the deformation behavior of B1500HS high-strength steel under different conditions.

The Constitutive Model for High Temperature Flow Behavior of SiC/6168Al Composite

2015 ◽  
Vol 1089 ◽  
pp. 37-41
Author(s):  
Jiang Wang ◽  
Sheng Li Guo ◽  
Sheng Pu Liu ◽  
Cheng Liu ◽  
Qi Fei Zheng
Keyword(s):  
Constitutive Model ◽  
Hot Deformation ◽  
Flow Behavior ◽  
Type Equation ◽  
Strain Rate Range ◽  
Compression Tests ◽  
Stress Strain ◽  
Hollomon Parameter ◽  
Proposed Model ◽  
Relationship Of

The hot deformation behavior of SiC/6168Al composite was studied by means of hot compression tests in the temperature range of 300-450 °C and strain rate range of 0.01-10 s-1. The constitutive model was developed to predict the stress-strain curves of this composite during hot deformation. This model was established by considering the effect of the strain on material constants calculated by using the Zenter-Hollomon parameter in the hyperbolic Arrhenius-type equation. It was found that the relationship of n, α, Q, lnA and ε could be expressed by a five-order polynomial. The stress-strain curves obtained by this model showed a good agreement with experimental results. The proposed model can accurately describe the hot flow behavior of SiC/6168Al composite, and can be used to numerically analyze the hot forming processes.

Constitutive Modeling for Flow Stress Behavior of Nimonic 80A Superalloy During Hot Deformation Process

2016 ◽  
Vol 35 (3) ◽  
pp. 327-336 ◽  
Author(s):  
Sendong Gu ◽  
Liwen Zhang ◽  
Chi Zhang ◽  
Wenfei Shen
Keyword(s):  
Flow Stress ◽  
Constitutive Model ◽  
Hot Deformation ◽  
Critical Strain ◽  
Volume Fraction ◽  
Constitutive Models ◽  
Avrami Equation ◽  
Peak Strain ◽  
Compression Tests ◽  
Nimonic 80A

AbstractThe hot deformation characteristics of nickel-based alloy Nimonic 80A were investigated by isothermal compression tests conducted in the temperature range of 1,000–1,200°C and the strain rate range of 0.01—5 s–1on a Gleeble-1500 thermomechanical simulator. In order to establish the constitutive models for dynamic recrystallization (DRX) behavior and flow stress of Nimonic 80A, the material constantsα,nand DRX activation energyQin the constitutive models were calculated by the regression analysis of the experimental data. The dependences of initial stress, saturation stress, steady-state stress, dynamic recovery (DRV) parameter, peak strain, critical strain and DRX grain size on deformation parameters were obtained. Then, the Avrami equation including the critical strain for DRX and the peak strain as a function of strain was established to describe the DRX volume fraction. Finally, the constitutive model for flow stress of Nimonic 80A was developed in DRV region and DRX region, respectively. The flow stress values predicted by the constitutive model are in good agreement with the experimental ones, which indicates that the constitutive model can give an accurate estimate for the flow stress of Nimonic 80A under the deformation conditions.

scholarly journals Constitutive Analysis on High-Temperature Flow Behavior of 3Cr-1Si-1Ni Ultra-High Strength Steel for Modeling of Flow Stress

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 42 ◽  
Author(s):  
Bingwang Lei ◽  
Gaoqiang Chen ◽  
Kehong Liu ◽  
Xin Wang ◽  
Xiaomei Jiang ◽  
...  
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Strain Rate ◽  
Constitutive Equations ◽  
High Strength Steel ◽  
Flow Behavior ◽  
High Strength ◽  
Strain Dependence ◽  
Constitutive Analysis ◽  
Ultra High Strength Steel

High-temperature plastic flow is the underlying process that governs the product quality in many advanced metal manufacturing technologies, such as extrusion, rolling, and welding. Data and models on the high-temperature flow behavior are generally desired in the design of these manufacturing processes. In this paper, quantitative constitutive analysis is carried out on 3Cr-1Si-1Ni ultra-high strength steel, which sheds light on the mathematic relation between the flow stress and the thermal-mechanical state variables, such as temperature, plastic strain, and strain rate. Particularly, the hyperbolic-sine equation in combination with the Zener-Hollomon parameter is shown to be successful in representing the effect of temperature and strain rate on the flow stress of the 3Cr-1Si-1Ni steel. It is found that the flow stress of the 3Cr-1Si-1Ni steel is significantly influenced by strain. The strain-dependence on flow stress is not identical at different temperatures and strain rates. In the constitutive model, the influence of strain in the constitutive analysis is successfully implemented by introducing strain-dependent constants for the constitutive equations. Fifth-order polynomial equations are employed to fit the strain-dependence of the constitutive constant. The proposed constitutive equations which considers the compensation of strain is found to accurately predict flow stress of the 3Cr-1Si-1Ni steel at the temperatures ranging from 800 °C to 1250 °C, strain rate ranging from 0.01/s to 10/s, and strain ranging from 0.05 to 0.6.

Hot Deformation Behavior and Constitutive Modeling of Alloy 800H Considering Effectsof Strain

2017 ◽  
Vol 36 (5) ◽  
pp. 467-475
Author(s):  
Rui Luo ◽  
Qi Zheng ◽  
Zhending Tang ◽  
Yongquan Yao ◽  
Guifang Xu ◽  
...  
Keyword(s):  
Flow Stress ◽  
Constitutive Model ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Testing Machine ◽  
Experimental Result ◽  
Strain Rates ◽  
Hot Deformation Behavior ◽  
Alloy 800H ◽  
Strain Dependent

AbstractHigh-temperature single-pass compression experiments were conducted on alloy 800H using a Gleeble 3500 thermal-mechanical simulation testing machine, and hot deformation behaviors at temperatures of 1,000–1,150 °C and strain rates of 0.01–1 s–1 were investigated. The results revealed that dynamic recrystallization (DRX) behavior occurred more easily under deformation conditions with relatively low strain rates and high deformation temperatures. By taking the influence of strain on the hot deformation behavior into consideration, a strain-dependent hyperbolic sine constitutive model was constructed. Based on this revised constitutive model, flow stress during deformation was predicted. The linear relation between the predicted value and the experimental result was as high as 0.99648, and the absolute average relative error was 2.019 %. Thus, it was demonstrated that the strain-dependent analysis provided a constitutive model that was able to precisely predict flow stress under experimental conditions.

scholarly journals Hot Deformation Behavior and Constitutive Modeling of H13-Mod Steel

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 846 ◽  
Author(s):  
Changmin Li ◽  
Yuan Liu ◽  
Yuanbiao Tan ◽  
Fei Zhao
Keyword(s):  
Constitutive Equation ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
High Strain ◽  
Flow Behavior ◽  
Peak Stress ◽  
Strain Rates ◽  
Hot Deformation Behavior ◽  
Stress Strain

The H13-mod steel optimized by composition and heat treatment has reached the performance index of the shield machine hob. The hot deformation behavior of the H13-mod steel was investigated by compression tests in the temperature range from 900 to 1150 °C and the strain rate range from 0.01 to 10 s−1. The true stress-strain curve showed that the rising stress at the beginning of deformation was mainly caused by work hardening. After the peak stress was attained, the curve drop and the flow softening phenomenon became more obvious at low strain rates. The flow behavior of the H13-mod steel was predicted by a strain-compensated Arrhenius-type constitutive equation. The relationship between the material constant in the Arrhenius-type constitutive equation and the true strain was established by a sixth-order polynomial. The correlation coefficient between the experimental value and the predicted value reached 0.987, which indicated that the constitutive equation can accurately estimate the flow stress during the deformation process. A good linear correlation was achieved between the peak stress (strain), critical stress (strain) and the Zener‒Hollomon parameters. The processing maps of the H13-mod steel under different strains were established. The instability region was mainly concentrated in the high-strain-rate region; however, the microstructure did not show any evidence of instability at high temperatures and high strain rates. Combined with the microstructure and electron backscattered diffraction (EBSD) test results under different deformations, the optimum hot working parameters were concluded to be 998–1026 °C and 0.01–0.02 s−1 and 1140–1150 °C and 0.01–0.057 s−1.

scholarly journals Determining Hot Deformation Behavior of an Advance High Strength Steel (AHSS) by Means of Dynamic Processing Maps

2019 ◽  
Vol 59 (1) ◽  
pp. 176-185 ◽  
Author(s):  
Xiang Gao ◽  
Démian Ruvalcaba ◽  
Lu Han ◽  
HongXiang Li ◽  
Begoña Santillana ◽  
...  
Keyword(s):  
Hot Deformation ◽  
High Strength Steel ◽  
Deformation Behavior ◽  
High Strength ◽  
Processing Maps ◽  
Hot Deformation Behavior ◽  
Dynamic Processing

Modeling of Flow Stress for one New Kind of Metastable β Titanium Alloy at High Temperature

2011 ◽  
Vol 311-313 ◽  
pp. 716-721
Author(s):  
Zhe Jun Wang ◽  
Hong Fu Qiang ◽  
Xue Ren Wang
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Flow Stress ◽  
Constitutive Model ◽  
Flow Behavior ◽  
Accurate Estimate ◽  
Compression Tests ◽  
Stress Strain ◽  
Nonlinear Constitutive Equation ◽  
Peak Value

Based on the characteristics of the flow stress curves for one new kind of metastable Ti2448 titanium alloy from isothermal hot compression tests, the constitutive model was developed to describe the relation between flow stress and strain, strain rate, deformation temperature completely. During this process, the flow behavior of alloy at high temperature undergo flow softening caused by dynamic recovery (DRV) was modeled by the adopted hyperbolic sine function based on the unified viscoplasticity theory, the further drop in flow stress after the peak value in stress-strain curves was assumed to be caused by temperature rise and the constitutive model was modified accordingly. Additionally, the material constants were determined by optimization strategies, which is a new method to solve the nonlinear constitutive equation. The stress-strain curves predicted by the developed constitutive model well agree with experimental results, which confirms that the developed constitutive model gives an accurate estimate of the flow stress of Ti2448 titanium alloy and can provide an effect method to model the flow behavior of metastable titanium alloy at high temperature.

Sign in / Sign up

Export Citation Format

Share Document