{111}<110> Orientation Induced Anisotropy of Shape Memory Effect in NiTiNb Pipe Joints

This work aims to clarify the influence of texture type and intensity on the shape memory effect (SME) in NiTiNb shape memory alloy (SMA) pipe joints, especially revealing the causes for the anisotropy of SME via texture changes. Three NiTiNb rods with different intensities of the {111}<110> texture were fabricated, and their microstructures, crystalline orientation distribution functions and inverse pole figures were obtained by X-ray diffraction and electron backscatter diffraction measurements. Simultaneously, the SME was characterized by inner-diameter recoverability of the corresponding pipe joints. For a given intensity of the {111}<110> texture, the SME of the NiTiNb pipe joints strongly depended on the expansion direction due to {111}<110> orientation-induced anisotropy of SME. In addition, both the SME and anisotropy of NiTiNb pipe joints increased with the increased intensity of the {111}<110> texture. Therefore, a suitable expansion direction and strong texture intensity should be considered for high SME in NiTiNb pipe joints.

Download Full-text

Fe-Mn-Si Based Shape Memory Alloys

MRS Proceedings ◽

10.1557/proc-246-309 ◽

1991 ◽

Vol 246 ◽

Cited By ~ 18

Author(s):

H. Otsuka

Keyword(s):

Shape Memory Alloys ◽

Shape Memory ◽

Shape Memory Effect ◽

Thermomechanical Treatment ◽

Memory Effect ◽

Room Temperature ◽

Steel Pipe ◽

Original Shape ◽

Ε Martensite ◽

Pipe Joints

AbstractFe-Mn-Si based alloys are non-thermoelastic shape memory alloys which utilize the stress-induced transformation from γ austenite to ε martensite. After these shape memory alloys are deformed at room temperature, they recover their original shape when heated to 473K or higher. Fe-Mn-Si based alloys contain 15% to 33% Mn, 5% to 6% Si, 0% to 13% Cr, and 0% to 10% Ni in weight. Mn and Si are indispensable for the development of shape memory effect (SME). The amounts of these elements require to be adjusted so that the Neel temperature (TN) lies lower than Ms temperature and the Ms lies just below room temperature. Though the volume of stress-induced martensite is only 20 to 30%, a thermomechanical treatment called “training” has made it possible for the alloy to recover from a tensi le deformation exceeding 3%. Today, the use of the shape memory al loys for steel pipe joints is being studied. They have already been put into practical use for an auxiliary bicycle part to clamp the frame.

Download Full-text

Tensile Failure of 55-Nitinol Wire

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100113858 ◽

1975 ◽

Vol 33 ◽

pp. 46-47

Author(s):

F. I. Grace

Keyword(s):

Shape Memory ◽

Shape Memory Effect ◽

Memory Effect ◽

Stoichiometric Composition ◽

Tensile Failure ◽

Initial State ◽

Initial Shape ◽

Nitinol Wire ◽

Cscl Type ◽

Shear Transformation

An interest in NiTi alloys with near stoichiometric composition (55 NiTi) has intensified since they were found to exhibit a unique mechanical shape memory effect at the Naval Ordnance Laboratory some twelve years ago (thus refered to as NITINOL alloys). Since then, the microstructural mechanisms associated with the shape memory effect have been investigated and several interesting engineering applications have appeared.The shape memory effect implies that the alloy deformed from an initial shape will spontaneously return to that initial state upon heating. This behavior is reported to be related to a diffusionless shear transformation which takes place between similar but slightly different CsCl type structures.

Download Full-text