scholarly journals Direct Plasmonic Solar Cell Efficiency Dependence on Spiro-OMeTAD Li-TFSI Content

Nanomaterials ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 3329
Author(s):  
Xinjian Geng ◽  
Mohamed Abdellah ◽  
Robert Bericat Vadell ◽  
Matilda Folkenant ◽  
Tomas Edvinsson ◽  
...  

The proliferation of the internet of things (IoT) and other low-power devices demands the development of energy harvesting solutions to alleviate IoT hardware dependence on single-use batteries, making their deployment more sustainable. The propagation of energy harvesting solutions is strongly associated with technical performance, cost and aesthetics, with the latter often being the driver of adoption. The general abundance of light in the vicinity of IoT devices under their main operation window enables the use of indoor and outdoor photovoltaics as energy harvesters. From those, highly transparent solar cells allow an increased possibility to place a sustainable power source close to the sensors without significant visual appearance. Herein, we report the effect of hole transport layer Li-TFSI dopant content on semi-transparent, direct plasmonic solar cells (DPSC) with a transparency of more than 80% in the 450–800 nm region. The findings revealed that the amount of oxidized spiro-OMeTAD (spiro+TFSI−) significantly modulates the transparency, effective conductance and conditions of device performance, with an optimal performance reached at around 33% relative concentration of Li-TFSI concerning spiro-OMeTAD. The Li-TFSI content did not affect the immediate charge extraction, as revealed by an analysis of electron–phonon lifetime. Hot electrons and holes were injected into the respective layers within 150 fs, suggesting simultaneous injection, as supported by the absence of hysteresis in the I–V curves. The spiro-OMeTAD layer reduces the Au nanoparticles’ reflection/backscattering, which improves the overall cell transparency. The results show that the system can be made highly transparent by precise tuning of the doping level of the spiro-OMeTAD layer with retained plasmonics, large optical cross-sections and the ultrathin nature of the devices.

Author(s):  
Muhammad Hassan Yousuf ◽  
Faisal Saeed ◽  
Haider Ali Tauqeer

Copper indium gallium selenide (CIGS) is an inexpensive material that has the potential to dominate the next-generation photovoltaic (PV) industry. Here we detail computational investigation of CIGS solar cell with encouragement of adopting cuprous dioxide (Cu2O) as a Hole Transport Layer (HTL) for efficient fabricated CIGS solar cells. Although Cu2O as a HTL has been studied earlier for perovskite and other organic/inorganic solar cell yet no study has been detailed on potential application of Cu2O for CIGS solar cells. With the proposed architecture, recombination losses are fairly reduced at the back contact and contribute to enhanced photo-current generation. With the introduction of Cu2O, the overall cell efficiency is increased to 26.63%. The wide-band of Cu2O pulls holes from the CIGS absorber which allows smoother extraction of holes with experiencing lesser resistance. Further, it was also inferred that, HTL also improves the quantum efficiency (QE) for photons with large wavelengths thus increases the cell operating spectrum.


2020 ◽  
Vol 5 (1) ◽  
pp. 27
Author(s):  
Abdelkader Hima

Solar cells based on organic-inorganic perovskites (PVK) are the subject of several researches in laboratories around the world. One of the most promising hybrid perovskite is the methylammonium lead tri-iodide MAPbI3 that is suitable for sun light harvesting. But the MAPbI3 is a toxic material, so in this paper is proposed another nature friendly candidate which is the methylammonium tin tri-iodide MASnI3. The proposed material is inserted into an n-i-p heterojunction solar cell which structure is electron transport layer (ETL)/PVK/hole transport layer (HTL). The used HTL is the PEDOT: PSS in combination with one of two ETLs which are the PCBM and the IGZO. Simulation efforts using 1D SCAPS was carried. It is found that IGZO ETL based solar cell yields a higher power conversion efficiency (PCE) compared with PCBM ETL based solar cell in the same thickness.   


2013 ◽  
Vol 14 (12) ◽  
pp. 3180-3185 ◽  
Author(s):  
Je-Hong Choi ◽  
Hak-Jong Choi ◽  
Ju-Hyeon Shin ◽  
Hyeong-Pil Kim ◽  
Jin Jang ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document