scholarly journals A Seismic Strengthening Technique for Reinforced Concrete Columns Using Sprayed FRP

Polymers ◽  
2016 ◽  
Vol 8 (4) ◽  
pp. 107 ◽  
Author(s):  
Kang Lee ◽  
Bang Lee ◽  
Soo Seo
Keyword(s):  
Reinforced Concrete ◽  
Concrete Columns ◽  
Seismic Strengthening ◽  
Reinforced Concrete Columns ◽  
Strengthening Technique

scholarly journals Analysis of the behavior of reinforced concrete columns strengthened with sleeve wedge bolts and a self compacting concrete layer

2015 ◽  
Vol 8 (2) ◽  
pp. 88-99
Author(s):  
M. G. Marques ◽  
A. P. A. R. Liserre ◽  
R. B. Gomes ◽  
G. N. Guimarães
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Concrete Columns ◽  
Concrete Surface ◽  
Self Compacting Concrete ◽  
Reinforced Concrete Columns ◽  
Concrete Layer ◽  
Strength Capacity ◽  
Strengthening Technique

Strengthening of reinforced concrete columns by jacketing is one of the most common structural rehabilitation techniques in Brazil. For adequate performance, it is necessary, among others, to avoid detachment of the new concrete layer (strengthening material) from the old concrete substrate when the strengthened member is again in service conditions. This paper describes the test results of eight reinforced concrete rectangular columns subjected to combined compression and one-axis bending to evaluate the efficiency of using sleeve wedge bolts across the new concrete/old concrete interface to avoid detachment. The strengthening technique, in this case, consists of adding a layer of self-compacting concrete to one face of the column. Two columns tested were monolithic and named PO (original column) e PR (reference column). The other six columns were strengthened using a new 35 mm thick self-compacting concrete layer attached to the column face subjected to highest compressive stresses. Column PO had a 120mm by 250 mm rectangular cross section and its results gave information about column behavior without the use of strengthening. Column PR had a 155mm by 250 mm rectangular cross section and its cross section dimensions matched the strengthened columns but it was cast monolithically. To improve bond conditions between the existing concrete and the new concrete, the concrete surface was roughened and the outermost aggregate was exposed using hydro jetting. Holes along the concrete surface were made to insert the wedge bolts responsible for increasing the bond between the two concrete surfaces. The difference among the six strengthened columns was the position and amount of bolts used. Results indicate that the position and amount of the bolts alters significantly the strength capacity of the columns, since premature rupture by concrete detachment was delayed.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

Sign in / Sign up

Export Citation Format

Share Document