A review of the methods of calculating stresses due to local loads and local attachments of pressure vessels

1969 ◽  
Keyword(s):  
1981 ◽  
Vol 16 (4) ◽  
pp. 217-226 ◽  
Author(s):  
M A Teixeira ◽  
R D McLeish ◽  
S S Gill

Simplified charts are presented for elastic stress concentration factors due to radial loads and circumferential and longitudinal moments applied to circular branches normal to cylindrical pressure vessels. The charts are based on the procedures given in Appendix G of BS 5500. The assumptions implied in Appendix G and the limitations on the geometrical parameters ro/r and r/t are discussed. A modification to Appendix G is suggested which is slightly more restrictive than at present. Published results for stresses due to local loads on branches in cylindrical vessels are compared with the values given by the charts.


1985 ◽  
Vol 107 (1) ◽  
pp. 51-59
Author(s):  
F. M. G. Wong ◽  
W. J. Craft ◽  
G. H. East

The Fourier solution for thin shell equations models pressure vessels as continuous simply connected surfaces with local loads. The technique allows placement of tractions with combinations of radial, shear, and axial components. Unlike Bijlaard, the solution in this paper includes loads placed at any position along the cylinder. Stiffness and the enhanced load-carrying capacity that internal pressure gives to thin vessels can be simulated. Numerical convergence problems are reduced by an improved displacement-load algorithm, and by use of load sites that allow the circular functions to be compactly grouped. A variety of loading distributions may be analyzed including large and small nozzles near and away from centerlines. Both rectangular and circular attachments are simulated. Through superposition, multiple attachments with their own loads may be examined. The attachments to the vessel may be either rigid or soft. A comparison to analytical results from Bijlaard shows excellent agreement. Comparisons with experimental tests on an API-650 nozzle on a storage tank are in good agreement. Variations between experimental and calculated results are primarily caused by assuming a simply supported base in the calculation, whereas in the experimental test, the base is more nearly fixed.


Author(s):  
T. Imura ◽  
S. Maruse ◽  
K. Mihama ◽  
M. Iseki ◽  
M. Hibino ◽  
...  

Ultra high voltage STEM has many inherent technical advantages over CTEM. These advantages include better signal detectability and signal processing capability. It is hoped that it will explore some new applications which were previously not possible. Conventional STEM (including CTEM with STEM attachment), however, has been unable to provide these inherent advantages due to insufficient performance and engineering problems. Recently we have developed a new 1250 kV STEM and completed installation at Nagoya University in Japan. It has been designed to break through conventional engineering limitations and bring about theoretical advantage in practical applications.In the design of this instrument, we exercised maximum care in providing a stable electron probe. A high voltage generator and an accelerator are housed in two separate pressure vessels and they are connected with a high voltage resistor cable.(Fig. 1) This design minimized induction generated from the high voltage generator, which is a high frequency Cockcroft-Walton type, being transmitted to the electron probe.


2020 ◽  
Vol 64 (1-4) ◽  
pp. 47-55
Author(s):  
Takuma Tomizawa ◽  
Haicheng Song ◽  
Noritaka Yusa

This study proposes a probability of detection (POD) model to quantitatively evaluate the capability of eddy current testing to detect flaws on the inner surface of pressure vessels cladded by stainless steel and in the presence of high noise level. Welded plate samples with drill holes were prepared to simulate corrosion that typically appears on the inner surface of large-scale pressure vessels. The signals generated by the drill holes and the noise caused by the weld were examined using eddy current testing. A hit/miss-based POD model with multiple flaw parameters and multiple signal features was proposed to analyze the measured signals. It is shown that the proposed model is able to more reasonably characterize the detectability of eddy current signals compared to conventional models that consider a single signal feature.


Sign in / Sign up

Export Citation Format

Share Document