1250-kilovolt scanning transmission electron microscope

1984 ◽  
Vol 42 ◽  
pp. 624-625
Author(s):  
T. Imura ◽  
S. Maruse ◽  
K. Mihama ◽  
M. Iseki ◽  
M. Hibino ◽  
...  
Keyword(s):  
High Voltage ◽  
Electron Probe ◽  
Scanning Transmission Electron Microscope ◽  
Pressure Vessels ◽  
Practical Applications ◽  
Voltage Generator ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
New Applications ◽  
High Voltage Generator

Ultra high voltage STEM has many inherent technical advantages over CTEM. These advantages include better signal detectability and signal processing capability. It is hoped that it will explore some new applications which were previously not possible. Conventional STEM (including CTEM with STEM attachment), however, has been unable to provide these inherent advantages due to insufficient performance and engineering problems. Recently we have developed a new 1250 kV STEM and completed installation at Nagoya University in Japan. It has been designed to break through conventional engineering limitations and bring about theoretical advantage in practical applications.In the design of this instrument, we exercised maximum care in providing a stable electron probe. A high voltage generator and an accelerator are housed in two separate pressure vessels and they are connected with a high voltage resistor cable.(Fig. 1) This design minimized induction generated from the high voltage generator, which is a high frequency Cockcroft-Walton type, being transmitted to the electron probe.

A Comparison of Scanning and Fixed Beam High Voltage Electron Microscopy

1973 ◽  
Vol 31 ◽  
pp. 6-7
Author(s):  
J. M. Cowley
Keyword(s):  
Electron Microscopy ◽  
High Voltage ◽  
Scanning Transmission Electron Microscope ◽  
Recording Time ◽  
High Voltage Electron Microscopy ◽  
Voltage Electron ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
High Voltage Supply ◽  
Fixed Beam

Since the theoretical advantage of high voltage microscopy in terms of improved resolution has not yet been achieved, the justification for the building of high voltage microscopes has been mainly the possibility of studying thicker specimens plus the observation of some radiation damage and some relativistic n-beam dynamical diffraction effects. For most of these purposes the scanning mode of transmission electron microscopy has clear advantages.As in the case of the fixed beam instrument (FBI), the limitation on resolution of the scanning transmission electron microscope (STEM) for ideal thin specimens is determined largely by instabilities of the high voltage supply and lens currents and by mechanical instabilities. In this respect the STEM suffers from the disadvantage that the point-by-point recording of the image involves a greater recording time and hence greater sensitivity to long term instabilities.

The High Resolution Scanning Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 316-317
Author(s):  
A. V. Crewe
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
High Vacuum ◽  
Scanning Transmission Electron Microscope ◽  
Ultra High Vacuum ◽  
Resolving Power ◽  
Imaging Characteristics ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
The Moment

The high resolution STEM is now a fact of life. I think that we have, in the last few years, demonstrated that this instrument is capable of the same resolving power as a CEM but is sufficiently different in its imaging characteristics to offer some real advantages.It seems possible to prove in a quite general way that only a field emission source can give adequate intensity for the highest resolution^ and at the moment this means operating at ultra high vacuum levels. Our experience, however, is that neither the source nor the vacuum are difficult to manage and indeed are simpler than many other systems and substantially trouble-free.

Resolution Attainable With the Present Day STEM

1973 ◽  
Vol 31 ◽  
pp. 230-231 ◽  
Author(s):  
J. S. Wall ◽  
J. P. Langmore ◽  
H. Isaacson ◽  
A. V. Crewe
Keyword(s):  
Spherical Aberration ◽  
Focal Length ◽  
Incident Beam ◽  
Scanning Transmission Electron Microscope ◽  
Aperture Size ◽  
Magnetic Lens ◽  
Peak Intensity ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Half Angle

The scanning transmission electron microscope (STEM) constructed by the authors employs a field emission gun and a 1.15 mm focal length magnetic lens to produce a probe on the specimen. The aperture size is chosen to allow one wavelength of spherical aberration at the edge of the objective aperture. Under these conditions the profile of the focused spot is expected to be similar to an Airy intensity distribution with the first zero at the same point but with a peak intensity 80 per cent of that which would be obtained If the lens had no aberration. This condition is attained when the half angle that the incident beam subtends at the specimen, 𝛂 = (4𝛌/Cs)¼

Enhancement of Contrast in the CEM and STEM Using Bumpy Specimens and Employing the “Dappled Field” Mode of Operation

1974 ◽  
Vol 32 ◽  
pp. 552-553 ◽  
Author(s):  
L. Gandolfi ◽  
J. Reiffel
Keyword(s):  
Operating Mode ◽  
Scanning Transmission Electron Microscope ◽  
Dark Field ◽  
Specimen Preparation ◽  
Field Mode ◽  
Preparation Methods ◽  
Scanning Transmission Electron ◽  
Transmission Electron ◽  
Mode Of Operation ◽  
Scanning Transmission

Calculations have been performed on the contrast obtainable, using the Scanning Transmission Electron Microscope, in the observation of thick specimens. Recent research indicates a revival of an earlier interest in the observation of thin specimens with the view of comparing the attainable contrast using both types of specimens.Potential for biological applications of scanning transmission electron microscopy has led to a proliferation of the literature concerning specimen preparation methods and the controversy over “to stain or not to stain” in combination with the use of the dark field operating mode and the same choice of technique using bright field mode of operation has not yet been resolved.

Development of 200 kV Scanning-Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 410-411
Author(s):  
H. Koike ◽  
S. Sakurai ◽  
K. Ueno ◽  
M. Watanabe
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Scanning Transmission Electron Microscope ◽  
The Other ◽  
Morphological Observation ◽  
Magnetic Domains ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Backscattered Electron ◽  
Increasing Demand

In recent years, there has been increasing demand for higher voltage SEMs, in the field of surface observation, especially that of magnetic domains, dislocations, and electron channeling patterns by backscattered electron microscopy. On the other hand, the resolution of the CTEM has now reached 1 ∼ 2Å, and several reports have recently been made on the observation of atom images, indicating that the ultimate goal of morphological observation has beem nearly achieved.

A Magnetic Spectrometer for a Scanning Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 436-437
Author(s):  
A. Kosiara ◽  
J. W. Wiggins ◽  
M. Beer
Keyword(s):  
Scanning Transmission Electron Microscope ◽  
Magnetic Spectrometer ◽  
Fringe Field ◽  
Curvature Radius ◽  
Magnetic Pole ◽  
Quadrupole Field ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Under Construction ◽  
Image Position

A magnetic spectrometer to be attached to the Johns Hopkins S. T. E. M. is under construction. Its main purpose will be to investigate electron interactions with biological molecules in the energy range of 40 KeV to 100 KeV. The spectrometer is of the type described by Kerwin and by Crewe Its magnetic pole boundary is given by the equationwhere R is the electron curvature radius. In our case, R = 15 cm. The electron beam will be deflected by an angle of 90°. The distance between the electron source and the pole boundary will be 30 cm. A linear fringe field will be generated by a quadrupole field arrangement. This is accomplished by a grounded mirror plate and a 45° taper of the magnetic pole.

To What Extent are Inelastically Scattered Electrons Useful in the Stem?

1973 ◽  
Vol 31 ◽  
pp. 286-287 ◽  
Author(s):  
H. Rose
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Electron Correlation ◽  
Quantum Noise ◽  
Collection Efficiency ◽  
Scanning Transmission Electron Microscope ◽  
Electron Cloud ◽  
Scanning Time ◽  
Transmission Electron ◽  
Scanning Transmission

The scanning transmission electron microscope offers the possibility of utilizing inelastically scattered electrons. Use of these electrons in addition to the elastically scattered electrons should reduce the scanning time (dose) Which is necessary to keep the quantum noise below a certain level. Hence it should lower the radiation damage. For high resolution, Where the collection efficiency of elastically scattered electrons is small, the use of Inelastically scattered electrons should become more and more favorable because they can all be detected by means of a spectrometer. Unfortunately, the Inelastic scattering Is a non-localized interaction due to the electron-electron correlation, occurring predominantly at the circumference of the atomic electron cloud.

SEM Examination of a Used Diamond Knife

1971 ◽  
Vol 29 ◽  
pp. 452-453
Author(s):  
J. Temple Black
Keyword(s):  
Electron Microscope ◽  
High Voltage ◽  
High Magnification ◽  
Metallic Materials ◽  
Wide Spread ◽  
Thin Sections ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Scanning Electron ◽  
Diamond Knife

Since its introduction by Fernandez-Moran, the diamond knife has gained wide spread usage as a common material for cutting of thin sections of biological and metallic materials into thin films for examination in the transmission electron microscope. With the development of high voltage E.M. and scanning transmission E.M., microtomy applications will become increasingly important in the preparation of specimens. For those who can afford it, the diamond knife will thus continue to be an important tool to accomplish this effort until a cheaper but equally strong and sharp tool is found to replace the diamond, glass not withstanding.In Figs. 1 thru 3, a first attempt was made to examine the edge of a used (β=45°) diamond knife by means of the scanning electron microscope. Because diamond is conductive, first examination was tried without any coating of the diamond. However, the contamination at the edge caused severe charging during imaging. Next, a thin layer of carbon was deposited but charging was still extensive at high magnification - high voltage settings. Finally, the knife was given a light coating of gold-palladium which eliminated the charging and allowed high magnification micrographs to be made with reasonable resolution.

Sign in / Sign up

Export Citation Format

Share Document