scholarly journals Heat transfer rates in hot shell, cold tube inclined baffled small shell, and tube heat exchanger using CFD and experimental approach

2021 ◽  
Vol 9 (4B) ◽  
Author(s):  
Devanand D. Chillal ◽  
◽  
Uday C. Kapale ◽  
N.R. Banapurmath ◽  
T. M. Yunus Khan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Liquid Flow ◽  
Cfd Analysis ◽  
Transfer Coefficients ◽  
Transfer Rates ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Shell And Tube ◽  
Cold Liquid

The work presented is an effort to realize the changes occurring for convective coefficients of heat transfer in STHX fitted with inclined baffles. Effort has been undertaken using Fluent, a commercially available CFD code ona CAD model of small STHX with inclined baffles with cold liquid flowing into the tubes and hot liquid flowing in the shell. Four sets of CFD analysis have been carried out. The hot liquid flow rate through shell compartments varied from 0.2 kg/sec to 0.8 kg/sec in steps of 0.2 kg/sec, while keeping the cold liquid flow condition in tube at 0.4 kg/sec constant. Heat transfer rates, compartment temperatures, and overall heat transfer coefficients, for cold liquid and hot liquid, were studied. The results given by the software using CFD approach were appreciable and comparatively in agreement with the results available by the experimental work, which was undertaken for the same set of inlet pressure conditions, liquid flow rates, and inlet temperatures of liquid for both hot and cold liquids. The experimental output results were also used to validate the results given by the CFD software. The results from the CFD analysis were further used to conclude the effect of baffle inclination on heat duty. The process thus followed also helped realize the effects of baffle inclination on convective heat transfer coefficient of the liquid flow through the shell in an inclined baffle shell and tube heat exchanger. The temperature plots for both cold and hot liquid were also generated for understanding the compartmental temperature distributions inclusive of the inlet and outlet compartments. The heat duty for a heat exchanger has been found to increase with the increase in baffle inclinations from zero degree to 20 degrees. Likewise, the convective heat transfer coefficients have also been found to increase with the increase in baffle inclinations.

Shell-and-Tube Side Heat Transfer Augmentation by the Use of Wall Radiation in a Crossflow Shell-and-Tube Heat Exchanger

1984 ◽  
Vol 106 (4) ◽  
pp. 735-742 ◽  
Author(s):  
Y. Yamada ◽  
M. Akai ◽  
Y. Mori
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Room Temperature ◽  
Heat Transfer Performance ◽  
Transfer Coefficients ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Heat Transfer Augmentation ◽  
Hot Gas ◽  
Shell And Tube

The heat transfer performance of a crossflow shell-and-tube heat exchanger for high-temperature use in which heat transfer is augmented by the use of wall radiation in both shell and tube sides, is studied. Radiation plates are inserted in the shell side, and twisted cross-tapes in the tube side. Overall heat transfer coefficients are measured to be about a maximum 80 percent larger than those without radiation, where the inlet temperatures of the hot gas range up to 800 °C, while those of the cold gas are about room temperature. Analytical results agree well with experimental results, and an approximate calculation procedure is found to be simple and accurate enough for practical use.

Internal, Shellside Heat Transfer and Pressure Drop Characteristics for a Shell and Tube Heat Exchanger

1985 ◽  
Vol 107 (2) ◽  
pp. 345-353 ◽  
Author(s):  
E. M. Sparrow ◽  
J. A. Perez
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Thermal Loading ◽  
Compartment Pressure ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Shell And Tube

Per-tube heat transfer coefficients and per-compartment and intracompartment pressure drops were measured on the shell side of a shell and tube heat exchanger. The main focus of the work was to determine the response of these quantities to variations in the size of the baffle window; the Reynolds number was also varied parametrically. The pressure measurements showed that the fluid flow is fully developed downstream of the first compartment of the heat exchanger and that the per-compartment pressure drop is constant in the fully developed regime. Within a compartment, the pressure drop in the upstream half is much larger than that in the downstream half. The per-tube heat transfer coefficients vary substantially within a given compartment (on the order of a factor of two), giving rise to a nonuniform thermal loading of the tubes. Row-average and compartment-average heat transfer coefficients were also evaluated. The lowest row-average coefficients were those for the first and last rows in a compartment, while the highest coefficient is that for the row just upstream of the baffle edge. It was demonstrated that the per-tube heat transfer coefficients are streamwise periodic for a module consisting of two consecutive compartments.

Performance of Heat Exchanger with Nanofluids

2021 ◽  
Vol 1021 ◽  
pp. 160-170
Author(s):  
Amer Hameed Majeed ◽  
Yasmin Hamed Abd
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Flow Rate ◽  
Hot Water ◽  
Transfer Coefficients ◽  
Maximum Enhancement ◽  
Transfer Rates ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Cold Fluid

The effect of adding nanomaterial of aluminum oxide (Al2O3), titanium oxide (TiO2) and zirconium oxide (ZrO2) in different concentrations of 0.25, 0.5, 0.75, 1.0, and 1.25 g/L to the cold fluid (water) turbulently flowing with different flow rates of 75, 100, 125, 150, and 175 L/min in tube side countercurrently to hot water flowing with a constant flow rate of 60 L/min in the shell side of shell and tube heat exchanger on the heat transfer rates and overall heat transfer coefficients are experimentally studied. It is found that the addition of nanomaterials gives rise to outlet cold (nano) fluids temperatures causing to enhancement averagely 7.74, 11.25, and 17.38 percent for ZrO2, TiO2, and Al2O3 respectively in heat transfer rate and averagely 12.72, 19.47, and 28.71 percent for ZrO2, TiO2, and Al2O3 respectively in overall heat transfer coefficients. The maximum enhancement values in heat transfer rates and in overall heat transfer coefficients are attained at a flow rate of 150 L/min of cold fluid.

scholarly journals Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets

Energies ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 3276 ◽  
Author(s):  
Jan Wajs ◽  
Michał Bajor ◽  
Dariusz Mikielewicz
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Waste Heat ◽  
Experimental Studies ◽  
Convection Heat Transfer ◽  
Test Facility ◽  
Experimental Investigations ◽  
Transfer Coefficients ◽  
Tube Heat Exchanger ◽  
Shell And Tube

In this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level in the described heat exchanger was done through the comparison with a shell-and-tube exchanger of a classical design. The thermal-hydraulic characteristics of both units were the subjects of comparison. They were constructed for the identical thermal conditions, i.e., volumetric flow rates of the working media and the media temperatures at the inlets to the heat exchanger. The experimental studies of both heat exchangers were conducted on the same test facility. An increase in the heat transfer coefficients values for the minijets heat exchanger was observed in comparison with the reference one, whereas the generated minijets caused greater hydraulic resistance. Experimentally confirmed intensification of heat transfer on the air side, makes the proposed minijets heat exchanger application more attractive, for the waste heat utilization systems from gas sources.

Experimental Study and Genetic-Algorithm-Based Correlation on Shell-Side Heat Transfer and Flow Performance of Three Different Types of Shell-and-Tube Heat Exchangers

2006 ◽  
Vol 129 (9) ◽  
pp. 1277-1285 ◽  
Author(s):  
Qiu-wang Wang ◽  
Gong-nan Xie ◽  
Bo-tao Peng ◽  
Min Zeng
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Shell Side ◽  
Heat Transfer Coefficients ◽  
Friction Factors ◽  
Shell And Tube

The heat transfer and pressure drop of three types of shell-and-tube heat exchangers, one with conventional segmental baffles and the other two with continuous helical baffles, were experimentally measured with water flowing in the tube side and oil flowing in the shell side. The genetic algorithm has been used to determine the coefficients of correlations. It is shown that under the identical mass flow, a heat exchanger with continuous helical baffles offers higher heat transfer coefficients and pressure drop than that of a heat exchanger with segmental baffles, while the shell structure of the side-in-side-out model offers better performance than that of the middle-in-middle-out model. The predicted heat transfer rates and friction factors by means of the genetic algorithm provide a closer fit to experimental data than those determined by regression analysis. The predicted corrections of heat transfer and flow performance in the shell sides may be used in engineering applications and comprehensive study. It is recommended that the genetic algorithm can be used to handle more complicated problems and to obtain the optimal correlations.

Sign in / Sign up

Export Citation Format

Share Document