scholarly journals CFD study of Convective Heat Transfer of Water Flow Through Micro-Pipe with Mixed Constant Wall Temperature and Heat Flux Wall Boundary Conditions

CFD letters ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 13-26
Author(s):  
Amjad Ali Pasha ◽  
Meshal Nuwaym Al-Harbi ◽  
Surfarazhussain S. Halkarni ◽  
Nazrul Islam ◽  
D. Siva Krishna Reddy ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boundary Conditions ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Constant Wall Temperature ◽  
Constant Property ◽  
Wall Boundary ◽  
Wall Boundary Conditions ◽  
Flow Through

The dissipation of heat in tiny engineering systems can be achieved with fluid flow through micro pipes. They have the advantage of less volume to large surface ratio convective heat transfer. There are deep-rooted analytical relations for convective heat transfer available for fluid flow through macro size pipes. But differences exist between the convective heat transfer for fluid flow through macro and micro pipes. Therefore, there is a good scope of work in micro convection heat transfer to study the mechanism of fundamental flow physics. There have been studies with either constant heat flux wall boundary conditions or constant wall temperature boundary conditions with constant and variable property flows. In this article, first, the numerical simulations are validated with the experimental data for 2D axisymmetric conventional pipe with pipe diameter of 8 mm is taken with laminar, steady, and single-phase water flows with constant wall heat flux boundary condition of 1 W/cm2. The computed Nusselt number is compared to the experimental results at different Reynolds numbers of 1350, 1600 and 1700. In the next study, three-dimensional micropipe laminar flow is studied numerically using water with an inlet velocity of 3 m/s and pipe diameter of 100 µm. The mixed wall boundary conditions with upper half pipe surface subjecting to constant wall temperature of 313 K and lower half surface subjecting to 100 W/cm2 are used in the simulations. The focus of research would be to consider the effect of temperature-dependent properties like thermal conductivity, viscosity, specific heat, and density (a combined effect we call it as variable properties) on micro-pipe flow characteristics like Nusselt number at mixed wall boundary conditions and compare it with the constant property flows. The conventional pipe showed no significant difference with variable and constant property flows with different Reynolds numbers. On contrary the flow through 3D micropipe shows that the Nusselt number with variable property flows is less as compared to the constant property flows.

scholarly journals The Effect of Inclination on Natural Convective Heat Transfer from a Slender Cuboid

Processes ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 1668
Author(s):  
Abdulrahim Kalendar ◽  
Yousuf Alhendal ◽  
Shafqat Hussain ◽  
Patrick Oosthuizen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Rayleigh Number ◽  
Boundary Conditions ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Vertical Axis ◽  
Surface Boundary ◽  
Nusselt Numbers ◽  
The Mean

A numerical study was undertaken of the naturally occurring laminar convective heat transfer from a slender cuboid with a relatively narrow cross-section (square) and an exposed top surface. The cuboid was perpendicularly placed on an adiabatic flat base plate and two types of surface boundary conditions were considered. The slender cuboid was inclined relative to the vertical axis at angles ranging from 0 to 180 degrees. The flow was considered symmetrical along the vertical axis of the slender cuboid. The equations governing the system were numerically solved in terms of dimensionless variables using FLUENT software. From the results obtained, mean Nusselt numbers over the slender cuboid were calculated using parameters such as: the Rayleigh number for heat flux, Ra*; the Rayleigh number, Ra; the slender cuboid dimensionless width, i.e., the ratio of the width to the height of the heated slender cuboid, W = w/h; and the position of the slender cuboid relative to the vertical, φ. Simulation results were produced for the boundary conditions of constant temperature, constant heat flux, and for Pr = 0.7. The effects of these parameters on the mean Nusselt number for the combined and for the individual surfaces of the slender cuboid are presented and the mean Nusselt numbers are correlated.

Analysis of flow and heat transfer over stretching/shrinking and porous surfaces

2021 ◽  
pp. 875608792110258
Author(s):  
Azhar Ali ◽  
Dil Nawaz Khan Marwat ◽  
Aamir Ali
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Current Model ◽  
Uniform Heat Flux ◽  
Similarity Transformations ◽  
Flow And Heat Transfer ◽  
Special Cases ◽  
Porous Surfaces

Flows and heat transfer over stretching/shrinking and porous surfaces are studied in this paper. Unusual and generalized similarity transformations are used for simplifying governing equations. Current model includes all previous cases of stretched/shrunk flows with thermal effects discussed so far. Moreover, we present three different cases of thermal behavior (i) prescribed surface temperature (ii) Variable/uniform convective heat transfer at plat surface and (iii) prescribed variable/uniform heat flux. Stretching/shrinking velocity Uw(x), porosity [Formula: see text], heat transfer [Formula: see text], heat flux [Formula: see text] and convective heat transfer at surface are axial coordinate dependent. Boundary layer equations and boundary conditions are transformed into nonlinear ODEs by introducing unusual and generalized similarity transformations for the variables. These simplified equations are solved numerically. Final ODEs represent suction/injection, stretching/shrinking, temperature, heat flux, convection effects and specific heat. This current problem encompasses all previous models as special cases which come under the scope of above statement (title). The results of classical models are scoped out as a special case by assigning proper values to the parameters. Numerical result shows that the dual solutions can be found for different possible values of the shrinking parameter. A stability analysis is accomplished and apprehended in order to establish a criterion for determining linearly stable and physically compatible solutions. The significant features and diversity of the modeled equations are scrutinized by recovering the previous problems of fluid flow and heat transfer from a uniformly heated sheet of variable (uniform) thickness with variable (uniform) stretching/shrinking and injection/suction velocities.

Scalable Heat Transfer Characterization on Film Cooled Geometries Based on Discrete Green’s Functions

2020 ◽  
Author(s):  
Jorge Saavedra ◽  
Venkat Athmanathan ◽  
Guillermo Paniagua ◽  
Terrence Meyer ◽  
Doug Straub ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flat Plate ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Green's Functions ◽  
Green’S Functions ◽  
Numerical Procedure ◽  
Local Heat Transfer ◽  
Sensitivity Matrix

Abstract The aerothermal characterization of film cooled geometries is traditionally performed at reduced temperature conditions, which then requires a debatable procedure to scale the convective heat transfer performance to engine conditions. This paper describes an alternative engine-scalable approach, based on Discrete Green’s Functions (DGF) to evaluate the convective heat flux along film cooled geometries. The DGF method relies on the determination of a sensitivity matrix that accounts for the convective heat transfer propagation across the different elements in the domain. To characterize a given test article, the surface is discretized in multiple elements that are independently exposed to perturbations in heat flux to retrieve the sensitivity of adjacent elements, exploiting the linearized superposition. The local heat transfer augmentation on each segment of the domain is normalized by the exposed thermal conditions and the given heat input. The resulting DGF matrix becomes independent from the thermal boundary conditions, and the heat flux measurements can be scaled to any conditions given that Reynolds number, Mach number, and temperature ratios are maintained. The procedure is applied to two different geometries, a cantilever flat plate and a film cooled flat plate with a 30 degree 0.125” cylindrical injection orifice with length-to-diameter ratio of 6. First, a numerical procedure is applied based on conjugate 3D Unsteady Reynolds Averaged Navier Stokes simulations to assess the applicability and accuracy of this approach. Finally, experiments performed on a flat plate geometry are described to validate the method and its applicability. Wall-mounted thermocouples are used to monitor the surface temperature evolution, while a 10 kHz burst-mode laser is used to generate heat flux addition on each of the discretized elements of the DGF sensitivity matrix.

Convective Heat Transfer Performance of FC-72 in a Pin-Finned Channel

2008 ◽  
Author(s):  
Liang-Han Chien ◽  
S.-Y. Pei ◽  
T.-Y. Wu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Flow Rate ◽  
Smooth Surface ◽  
Heat Transfer Performance ◽  
Fluid Temperature ◽  
Transfer Performance ◽  
Finned Surface

This study investigates the influence of the heat flux and mass velocity on convective heat transfer performance of FC-72 in a rectangular channel of 20mm in width and 2 mm in height. The heated side has either a smooth surface or a pin-finned surface. The inlet fluid temperature is maintained at 30°C. The total length of the test channel is 113 mm, with a heated length of 25mm. The flow rate varies between 80 and 960 ml/min, and the heat flux sets between 18 and 50 W/cm2. The experimental results show that the controlling variable is heat flux instead of flow rate because of the boiling activities in FC-72. At a fixed flow rate, the pin-finned surface yields up to 20% higher heat transfer coefficient and greater critical heat flux than those of a smooth surface.

Sign in / Sign up

Export Citation Format

Share Document