Analysis of Human Body Injury by Non-penetrating Ballistic Impact Using a Finite Element Model of the Head and Neck

2017 ◽  
Vol 41 (1) ◽  
pp. 1-6
Author(s):  
Moon Jeong Kang ◽  
Young Nam Jo ◽  
Jeawook Chae ◽  
Hong Hee Yoo
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Head And Neck ◽  
Human Body ◽  
Element Model ◽  
Ballistic Impact

Experimentally validated predictive finite element modeling of the V0-V100 probabilistic penetration response of a Kevlar fabric against a spherical projectile

2018 ◽  
Vol 9 (4) ◽  
pp. 504-524 ◽  
Author(s):  
Gaurav Nilakantan
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Modeling ◽  
Element Model ◽  
Ballistic Impact ◽  
Impact Testing ◽  
Woven Fabric ◽  
Projectile Impact ◽  
Element Modeling ◽  
The Impact

This work presents the first fully validated and predictive finite element modeling framework to generate the probabilistic penetration response of an aramid woven fabric subjected to ballistic impact. This response is defined by a V0-V100 curve that describes the probability of complete fabric penetration as a function of projectile impact velocity. The exemplar case considered in this article comprises a single-layer, fully clamped, plain-weave Kevlar fabric impacted at the center by a 0.22 cal spherical steel projectile. The fabric finite element model comprises individually modeled three-dimensional warp and fill yarns and is validated against the experimental material microstructure. Sources of statistical variability including yarn strength and modulus, inter-yarn friction, and precise projectile impact location are mapped into the finite element model. A series of impact simulations at varying projectile impact velocities is executed using LS-DYNA on the fabric models, each comprising unique mappings. The impact velocities and outcomes (penetration, non-penetration) are used to generate the numerical V0-V100 curve which is then validated against the experimental V0-V100 curve obtained from ballistic impact testing and shown to be in excellent agreement. The experimental data and its statistical analysis used for model input and validation, namely, the Kevlar yarn tensile strengths and moduli, inter-yarn friction, and fabric ballistic impact testing, are also reported.

A Comparative Study of the Human Body Finite Element Model Under Blast Loadings

2012 ◽  
Author(s):  
X. G. Tan ◽  
R. Kannan ◽  
Andrzej J. Przekwas
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Human Body ◽  
Material Properties ◽  
Complex Geometry ◽  
Blast Loading ◽  
Element Model ◽  
Stress Wave Propagation ◽  
Brain Response ◽  
Time Step

Until today the modeling of human body biomechanics poses many great challenges because of the complex geometry and the substantial heterogeneity of human body. We developed a detailed human body finite element model in which the human body is represented realistically in both the geometry and the material properties. The model includes the detailed head (face, skull, brain, and spinal cord), the skeleton, and air cavities (including the lung). Hence it can be used to accurately acquire the stress wave propagation in the human body under various loading conditions. The blast loading on the human surface was generated from the simulated C4 blast explosions, via a novel combination of 1-D and 3-D numerical formulations. We used the explicit finite element solver in the multi-physics code CoBi for the human body biomechanics. This is capable of solving the resulting large system containing millions of unknowns in an extremely scalable fashion. The meshes generated for these simulations are of good quality. This enables us to employ relatively large time step sizes, without resorting to the artificial time scaling treatment. In order to study the human body dynamic response under the blast loading, we also developed an interface to apply the blast pressure loading on the external human body surface. These newly developed models were used to conduct parametric simulations to find out the brain biomechanical response when the blasts impact the human body. Under the same blast loading we also show the differences of brain response when having different material properties for the skeleton, the existence of other body parts such as torso.

Finite-Element Modelling of Ballistic Impact of Plain-Woven Aramid Fabric

2014 ◽  
Vol 553 ◽  
pp. 769-773 ◽  
Author(s):  
E.A. Flores-Johnson ◽  
J.G. Carrillo ◽  
R.A. Gamboa ◽  
Lu Ming Shen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Modelling ◽  
Permanent Deformation ◽  
Element Model ◽  
Ballistic Impact ◽  
Elastic Model ◽  
Numerical Predictions ◽  
Aramid Fabric ◽  
The Finite Element Model

In this work, a 3D finite-element model of the ballistic impact of a multi-layered plain-woven aramid fabric style 720 (Kevlar®129 fibre, 1420 denier, 20×20 yarns per inch) impacted by a 6.7-mm spherical projectile was built at the mesoscale in Abaqus/Explicit by modelling individual crimped yarns. Material properties and yarn geometry for the model were obtained from reported experimental observations. An orthotropic elastic model with a failure criterion based on the tensile strength of the yarns was used. Numerical predictions were compared with available experimental data. It was found that the finite-element model can reproduce the physical experimental observations, such as the straining of primary yarns and pyramidal-shaped deformation after perforation. The permanent deformation of fabric targets predicted by the numerical simulations was compared with available experimental results. It was found that the model fairly predicted the permanent deformation with a difference of about 21% when compared with experiments.

Chest Deflection vs. Chest Acceleration as Injury Indicator in Front Impact Simulations Using Full Human Body Finite Element Model

2009 ◽  
Author(s):  
Raed E. El-Jawahri ◽  
Jesse S. Ruan ◽  
Stephen W. Rouhana ◽  
Saeed D. Barbat
Keyword(s):  
Finite Element ◽  
Plastic Strain ◽  
Finite Element Model ◽  
Human Body ◽  
Element Model ◽  
Von Mises Stress ◽  
Head Acceleration ◽  
Blunt Impact ◽  
Von Mises ◽  
Impact Simulations

The Ford Motor Company Human Body Finite Element Model (FHBM) was validated against rib dynamic tension and 3-point bending tests. The stress-strain and moment-strain data from the tension and bending simulations respectively were compared with human rib specimen test data. The model used represented a 50th percentile adult male. It was used to compare chest deflection and chest acceleration as thoracic injury indicator in blunt impact and belted occupants in front sled impact simulations. A 150 mm diameter of 23.4 kg impactor was used in the blunt impact simulations with impact speeds of 2, 4, and 8 m/s. In the Front sled impact simulations, single-step acceleration pulses with peaks of 10, 20, and 30 g were used. The occupants were restrained by 3-point belt system, however neither pretensioner nor shoulder belt force limiter were used. The external force, head acceleration, chest deflection, chest acceleration, and the maximum values of Von Mises stress and plastic strain were the model outputs. The results showed that the external contact force, head acceleration, chest deflection, and chest acceleration in the blunt impact simulations varied between 1.5–7 kN, 5–28 g, 18–80 mm, and 8–40 g respectively. The same responses varied between 7–24 kN, 13–40 g, 15–50 mm, and 16–46 g respectively in the front sled impact simulations. The maximum Von Mises stress and plastic strain were 50–127 MPa, and 0.04–2% respectively in the blunt impact simulations and 72–134 MPa, and 0.13–3% respectively in the sled impact simulations.

scholarly journals Biomechanics Of Human Lumbar Spine (L3 To L5) With Degenerative Disc Disease Using Finite Element Model

2019 ◽  
Vol 8 (6) ◽  
pp. 4609-4614
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Finite Element Model ◽  
Disc Degeneration ◽  
Human Body ◽  
Lumbar Disc ◽  
Element Model ◽  
Human Spine ◽  
Human Lumbar Spine ◽  
Normal Human

Human spine is one of the complex structure of the human body. It provides the link between upper and lower extremities of the human body. It is estimated that at least 30% of people in the middle age group from thirty to fifty years have some degree of disc degeneration. Disc degeneration disease can affect the quality of life and in certain individual it can cause severe chronic pain if left untreated. The low back pain associated with lumbar disc degeneration is usually generated from two causes which are abnormal motion instability and inflammation. Abnormal motion instability occurs when the annulus fibrosus are worn down and cannot absorb stress on the human spine effectively resulting in changes in movements along the vertebral segment. To understand lumbar disc problem, a thorough knowledge of the biomechanics of the normal human lumbar spine and a disc degenerated lumbar spine is of great importance. In this study, Computed tomography image of a 33 year old male is used. A three dimensional (3D) human lumbar spine (L3 to L5) is created and validated with literature. The finite element model was modified to degenerated disc and studied the biomechanics of the lumbar spine. Comparison of the biomechanics of normal human lumbar spine is done with the human lumbar spine with disc degeneration for different range of motion and different loads. The result shows that the pressure generated on degenerated disc is greater than normal disc. This work can be implemented and used for designing implants and also for intervertebral disc related analysis

Sign in / Sign up

Export Citation Format

Share Document