Modeling for Machine Tool Thermal Error Based on Grey Model Preprocessing Neural Network

2011 ◽  
Vol 47 (07) ◽  
pp. 134 ◽  
Author(s):  
Yi ZHANG
Keyword(s):  
Neural Network ◽  
Machine Tool ◽  
Thermal Error ◽  
Grey Model

Research on Thermal Error Modeling of NC Machine Tool Based on BP Neural Networks

2009 ◽  
Vol 626-627 ◽  
pp. 135-140 ◽  
Author(s):  
Qian Jian Guo ◽  
X.N. Qi
Keyword(s):  
Neural Network ◽  
Neural Networks ◽  
Machine Tool ◽  
Ant Colony Algorithm ◽  
Thermal Error ◽  
Error Modeling ◽  
Minimum Problem ◽  
Bp Neural Networks ◽  
Nc Machine Tool ◽  
Nc Machine

Through analysis of the thermal errors affected NC machine tool, a new prediction model based on BP neural networks is presented, and ant colony algorithm is applied to train the weights of neural network model. Finally, thermal error compensation experiment is implemented, and the thermal error is reduced from 35μm to 6μm. The result shows that the local minimum problem of BP neural network is overcome, and the model accuracy is improved.

Prediction of Machine Tool Thermal Error Compensation Based on SVMR and ARM11

2015 ◽  
Vol 740 ◽  
pp. 120-126
Author(s):  
Zhi Peng Zhang ◽  
Kang Liu ◽  
Feng Guo
Keyword(s):  
Neural Network ◽  
Support Vector Machine ◽  
Machine Tool ◽  
Bp Neural Network ◽  
Error Compensation ◽  
Thermal Error ◽  
Support Vector ◽  
Experiment Research ◽  
Further Development ◽  
Thermal Error Compensation

In order to improve the process precision of the machine tool, further development of SVMR was achieved by QT Creator. Support vector machine was applied to the ARM11 development board, SVMR model was online trained and real-time predicted the values of machine tool thermal error. Compared with the widely used BP neural network, this method has the characteristics of high compensation precision and strong generalization ability. Experiment research has proved that the stronger effectiveness and higher accuracy using this method.

Application and Study of Fuzzy Neural Network Theory Based on Takagi-Sugeno Model to Thermal Error Modeling on NC Machine Tool

2013 ◽  
Vol 744 ◽  
pp. 147-152
Author(s):  
Zi Jian Liu ◽  
Zhi Min Yu ◽  
Si Ming Li ◽  
Yan Di Ai
Keyword(s):  
Neural Network ◽  
Machine Tool ◽  
Fuzzy Neural Network ◽  
Thermal Error ◽  
Error Modeling ◽  
Nc Machine Tool ◽  
Fuzzy Neural ◽  
Nc Machine ◽  
Sugeno Model ◽  
Takagi Sugeno

For the degree of thermal deformation nonlinear is high and difficult to predict, fuzzy neural network modeling (FNN) based on Takagi-Sugeno model was applied to the NC machine tool thermal error modeling thus the complete thermal error fuzzy neural network mathematical model on NC machine tool was established and network parameters initialization and learning method were discussed. Thermal error experiment was conducted on large NC gantry rail grinder spindle box system and two independent groups of spindle thermal error data were collected, one was used to establish thermal error fuzzy neural network prediction model and another one was used to verify the prediction accuracy of this model. The test results show that fuzzy neural network model has high prediction accuracy.

Application of Partial Least Squares Neural Network in Thermal Error Modeling for CNC Machine Tool

2008 ◽  
Vol 392-394 ◽  
pp. 30-34 ◽  
Author(s):  
J.H. Shen ◽  
Jian Guo Yang
Keyword(s):  
Neural Network ◽  
Machine Tool ◽  
Least Squares ◽  
Partial Least Squares ◽  
Thermal Error ◽  
Error Modeling ◽  
Neural Network Modeling ◽  
Cnc Machine Tool ◽  
Cnc Machine ◽  
Thermal Error Modeling

This paper presents a partial least squares neural network modeling method for CNC machine tool thermal errors. This method uses the neural network learning rule to obtain the PLS parameters instead of the traditional linear method in partial least squares regression so as to overcome the multicollinearity and nonlinearity problem in thermal error modeling. The basic principle and architecture of PLSNN is described and the new method is applied on the thermal error modeling for a CNC turning center. After model validation with two groups of new testing data and performance comparison with other five different modeling methods, PLSNN performs better than the others with better robustness.

scholarly journals An Unsupervised Regularization and Dropout based Deep Neural Network and Its Application for Thermal Error Prediction

2020 ◽  
Vol 10 (8) ◽  
pp. 2870
Author(s):  
Yang Tian ◽  
Guangyuan Pan
Keyword(s):  
Neural Network ◽  
Prediction Model ◽  
Machine Tool ◽  
Deep Neural Network ◽  
Thermal Error ◽  
Error Modeling ◽  
Error Prediction ◽  
Learning Technology ◽  
Heavy Duty ◽  
Self Organizing

Due to the large size of the heavy duty machine tool-foundation systems, space temperature difference is high related to thermal error, which affects to system’s accuracy greatly. The recent highly focused deep learning technology could be an alternative in thermal error prediction. In this paper, a thermal prediction model based on a self-organizing deep neural network (DNN) is developed to facilitate accurate-based training for thermal error modeling of heavy-duty machine tool-foundation systems. The proposed model is improved in two ways. Firstly, a dropout self-organizing mechanism for unsupervised training is developed to prevent co-adaptation of the feature detectors. In addition, a regularization enhanced transfer function is proposed to further reduce the less important weights of the process and improve the network feature extraction capability and generalization ability. Furthermore, temperature sensors are used to acquire temperature data from the heavy-duty machine tool and concrete foundation. In this way, sample data of thermal error predictive model are repeatedly collected from the same locations at different times. Finally, accuracy of the thermal error prediction model was validated by thermal error experiments, thus laying the foundation for subsequent studies on thermal error compensation.

Sign in / Sign up

Export Citation Format

Share Document