Plastic Deformation Analysis of Thin-walled Tube Bending under Internal Pressure

2012 ◽  
Vol 48 (14) ◽  
pp. 78 ◽  
Author(s):  
Lan HU
Keyword(s):  
Plastic Deformation ◽  
Internal Pressure ◽  
Deformation Analysis ◽  
Tube Bending ◽  
Thin Walled Tube ◽  
Thin Walled

Springback Angle and Plastic Elongation Prediction of Thin-Walled Tube Bending by FEM

2012 ◽  
Vol 152-154 ◽  
pp. 456-461 ◽  
Author(s):  
W.J. Dan ◽  
W.G. Zhang
Keyword(s):  
Plastic Deformation ◽  
Finite Element ◽  
Dimensional Accuracy ◽  
Radius Of Curvature ◽  
Tube Bending ◽  
Bending Angle ◽  
Plastic Elongation ◽  
Thin Walled Tube ◽  
Thin Walled ◽  
Springback Angle

Springback is an inevitable phenomenon while the load is released due to the elastic property after tube bending. This leads to an increase in the radius of curvature and elongation by plastic deformation, a reduction in the bending angle of the bent tube, a decrease in dimensional accuracy and fits with others difficulty. By elastic–plastic finite element methods (FEM), a reasonable simulation model for thin-walled tube bending is established to define the relationships between process parameters and springback angle, plastic deformation. With 210 kinds of models, the results show that: 1) Springback angle and plastic elongation of bending tube are related to bending angle, bending die diameter and tube thickness. 2) Controlling functions for plastic elongation and springback angle in bending tube process are given, which is verified by tube bending experiments.

scholarly journals A New Method of Manufacturing Thin-Walled Tube Made of AZ61 Magnesium Alloy Including Direct Extrusion And Corrugated Equal Channel Angular Extrusion

2021 ◽  
Author(s):  
H-J Hu ◽  
Ou Zhang ◽  
Gang Hu ◽  
Hui Zhao ◽  
Zhongwen OU
Keyword(s):  
Plastic Deformation ◽  
Magnesium Alloy ◽  
Large Scale ◽  
Equal Channel Angular Extrusion ◽  
Process Conditions ◽  
Workpiece Material ◽  
Plastic Deformation Behavior ◽  
Angular Extrusion ◽  
Thin Walled Tube ◽  
Thin Walled

Abstract Due to demand of strong toughness of thin walled tube, and good secondary forming properties and high-precision dimension, New plastic forming method should be researched to achieve a complete filling, uniform deformation and microstructure evolution during forming process.To obtain the deformation mechanisms of a new composite extrusion for thin walled tube fabricated by tube corrugated equal channel angular extrusion has been researched which is shorten as “TC-ECAE” in this paper. Finite element DEFORMTM-3D software to investigate the plastic deformation behavior of magnesium billet during TC-ECAE process has been employed. Computed parameters including workpiece material characteristics and process conditions have been taken into consideration. The pridictions of strains distributions and damage distributions and effective stress distributions and flow velocities distributions and microstructures evolutions have been explored. The results proved that the TC-ECAE process is a forming method for magnesium alloy tube which is suitable for large scale industrial application. The TC-ECAE process would cause serve plastic deformation and improve the dynamic recrystallization of magnesium alloy during TC-ECAE process.

Tube-Bulging Under Internal Pressure and Axial Force

1973 ◽  
Vol 95 (4) ◽  
pp. 219-223 ◽  
Author(s):  
D. M. Woo
Keyword(s):  
Internal Pressure ◽  
Numerical Solution ◽  
Axial Force ◽  
Compressive Load ◽  
Experimental Results ◽  
Longitudinal Stress ◽  
Thin Walled Tube ◽  
Thin Walled ◽  
Tube Bulging

A numerical solution for analysis of the bulging process of a thin-walled tube under internal pressure and axial force is proposed. The solution is applied to a case in which the longitudinal stress resulted from internal pressure and external compressive load is tensile along the whole length of the bulged tube. To verify whether the solution is applicable, theoretical and experimental results on the bulging of copper tubes have been obtained and are compared in this paper.

The Effect of Anisotropy on Thin-Walled Tube Bending

2011 ◽  
Author(s):  
K. Hasanpour ◽  
B. Amini ◽  
M. Poursina ◽  
M. Barati
Keyword(s):  
Tube Bending ◽  
Thin Walled Tube ◽  
Thin Walled

CONTINUUM DAMAGE MECHANICS ANALYSIS OF THIN-WALLED TUBE UNDER CYCLIC BENDING AND INTERNAL CONSTANT PRESSURE

2013 ◽  
Vol 05 (04) ◽  
pp. 1350038 ◽  
Author(s):  
H. YAZDANI ◽  
A. NAYEBI
Keyword(s):  
Internal Pressure ◽  
Damage Mechanics ◽  
Low Cycle Fatigue ◽  
Kinematic Hardening ◽  
Damage Model ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Cyclic Bending ◽  
Thin Walled Tube ◽  
Thin Walled

Ratcheting and fatigue damage of thin-walled tube under cyclic bending and steady internal pressure is studied. Chaboche's nonlinear kinematic hardening model extended by considering the effect of continuum damage mechanics employed to predict ratcheting. Lemaitre damage model [Lemaitre, J. and Desmorat, R. [2005] Engineering Damage Mechanics (Springer-Verlag, Berlin)] which is appropriate for low cyclic loading is used. Also the evolution features of whole-life ratcheting behavior and low cycle fatigue (LCF) damage of the tube are discussed. A simplified method related to the thin-walled tube under bending and internal pressure is used and compared well with experimental results. Bree's interaction diagram with boundaries between shakedown and ratcheting zone is determined. Whole-life ratcheting of thin-walled tube reduces obviously with increase of internal pressure.

Sign in / Sign up

Export Citation Format

Share Document