Study on the Arrangement of Baffles Attenuating Blast Waves inside Tunnels

2012 ◽  
Vol 204-208 ◽  
pp. 1380-1384 ◽  
Author(s):  
Hong Qin Lu ◽  
Wei Qing Liu ◽  
Tong Zhao

Explosion inside the entrance of a tunnel may produce strong blast wave in the tunnel. Taking effective measures to attenuate the air blast wave is very important. Numerical simulations were done on explosion inside the entrance of a tunnel in three different cases, no baffles, symmetrical baffles and stagger baffles arranged along the tunnel. It is found that the arrangement of baffles can attenuate the air blast wave effectively. The best arrangement of baffles is given and it is a reference for tunnel protective design and study.

2018 ◽  
Vol 910 ◽  
pp. 78-83 ◽  
Author(s):  
Yuta Sugiyama ◽  
Tomotaka Homae ◽  
Kunihiko Wakabayashi ◽  
Tomoharu Matsumura ◽  
Yoshio Nakayama

This paper investigates explosions in a straight square tube in order to understand the mitigation effect of water on blast waves that emerge outside. Numerical simulations are used to assess the effect of water that is put inside the tube. The water reduces the peak overpressure outside, which agrees well with the experimental data. The increases in the kinetic and internal energies of the water are estimated, and the internal energy transfer at the air/water interface is shown to be an important factor in mitigating the blast wave in the present numerical method.


2018 ◽  
Vol 2018 ◽  
pp. 1-18 ◽  
Author(s):  
Hrvoje Draganić ◽  
Damir Varevac

Results of numerical simulations of explosion events greatly depend on the mesh size. Since these simulations demand large amounts of processing time, it is necessary to identify an optimal mesh size that will speed up the calculation and give adequate results. To obtain optimal mesh sizes for further large-scale numerical simulations of blast wave interactions with overpasses, mesh size convergence tests were conducted for incident and reflected blast waves for close range bursts (up to 5 m). Ansys Autodyn hydrocode software was used for blast modelling in axisymmetric environment for incident pressures and in a 3D environment for reflected pressures. In the axisymmetric environment only the blast wave propagation through the air was considered, and in 3D environment blast wave interaction and reflection of a rigid surface were considered. Analysis showed that numerical results greatly depend on the mesh size and Richardson extrapolation was used for extrapolating optimal mesh size for considered blast scenarios.


1981 ◽  
Vol 71 (6) ◽  
pp. 1731-1741
Author(s):  
I. N. Gupta ◽  
R. A. Hartenberger

Abstract An analysis of seismic field data from surface shots in two radically different geologic environments shows significantly different seismic phases at the two sites. At the first site, which has a layered sedimentary section, five distinct phases are observed: the P-wave first arrival; a complex wave train consisting of higher mode Rayleigh waves; a precursor to air-blast wave; the air blast wave; and the air-coupled Rayleigh waves. Records from the second site, overlying an unlayered mass of igneous rocks, show only three distinct seismic phases: the P-wave first arrival; a simple wave train of fundamental-mode Rayleigh and Love waves; and an air blast wave. Peak ground velocity, based on the average of the three largest amplitudes in the surface waves preceding the air blast wave, scales well with yield for both sites. Measurements of peak ground velocity may be used to estimate yields of explosive charges at either site within a factor of about 2 if the source distance is known. The scaling relationship appears to be valid over a wide range of yields and site geological conditions.


1958 ◽  
Vol 1 (2) ◽  
pp. 95 ◽  
Author(s):  
Everett F. Cox
Keyword(s):  

2021 ◽  
Author(s):  
Sunil Sutar ◽  
Shailesh Ganpule

The response of the brain to the explosion induced primary blast waves is actively sought. Over the past decade, reasonable progress has been made in the fundamental understanding of bTBI using head surrogates and animal models. Yet, the current understanding of how blast waves interact with the human is in nascent stages, primarily due to lack of data in humans. The biomechanical response in human is critically required so that connection to the aforementioned bTBI models can be faithfully established. Here, using a detailed, full-body human model, we elucidate the biomechanical cascade of the brain under a primary blast. The input to the model is incident overpressure as achieved by specifying charge mass and standoff distance through ConWep. The full-body model allows to holistically probe short- (<5 ms) and long-term (200 ms) brain biomechanical responses. The full-body model has been extensively validated against impact loading in the past. In this work, we validate the head model against blast loading. We also incorporate structural anisotropy of the brain white matter. Blast wave human interaction is modeled using a conventional weapon modeling approach. We demonstrate that the blast wave transmission, linear and rotational motion of the head are dominant pathways for the biomechanical loading of the brain, and these loading paradigms generate distinct biomechanical fields within the brain. Blast transmission and linear motion of the head govern the volumetric response, whereas the rotational motion of the head governs the deviatoric response. We also observe that blast induced head rotation alone produces a diffuse injury pattern in white matter fiber tracts. Lastly, we find that the biomechanical response under blast is comparable to the impact event. These insights will augment laboratory and clinical investigations of bTBI and help devise better blast mitigation strategies.


1963 ◽  
Author(s):  
C. Wilton ◽  
N.R. Wallace ◽  
K. Kaplan
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document